UH5040R - Radio UNIDEN - Free user manual and instructions

USER MANUAL UH5040R UNIDEN

For more exciting new products please visit our website:

Australia: www.uniden.com.au

OWNER'S MANUAL

Introduction 3

Features 3

Preventive Maintenance 4 Troubleshooting 4

Controls / Connectors 5 Indicators 6

Included with Your UH5040R Transceiver 7

Optional Accessories 7

Slide Mount Bracket 8

Mounting the MIC Hanger 10

Operation 11

Turn ON the Power and Set the Volume 11

Setting the Squelch 11 Monitor 12

Selecting a Channel 12

Set the LCD Dimmer 12 Transmitting 13

Call Function 13

Using Repeater Channels 14

Operating the UH5040R in Duplex Mode Scanning 15 15

Open Scan (OS) Mode 16

Group Scan (GS) Mode 17

Programming Scan Channels 18

Selecting the Call tone 18

Busy Channel Lockout 19 Roger Beep 19

Programming the Instant Priority Channel 20

Recalling the Instant Channel 20

CTCSS (Continuous Tone Coded Squelch System) 20

DCS (Digitally Coded Squelch) 20

UHF CB Channel Guidelines 21

UHF CB Channels & Frequencies 22

CTCSS codes table 24

DCS codes table 25

Warranty 26

The Uniden UH5040R is designed to provide you with years of trouble free service. Its rugged components and materials are capable of withstanding harsh environments. Please read this Operating Manual carefully to ensure you gain the optimum performance of the unit.

NOTE

The citizen band radio service is licenced in Australia by ACMA Radio-communications (Citizen Band Radio Stations) Class Licence and in New Zealand by MBIE General User Licence for Citizen Band Radio and operation is subject to conditions contained in those licenses.

Features

• Narrow Band (NB) 80 Channel Radio*
  • Transmission Power 5W
  • Built-in AVS Circuitry ^†
• LCD Display with Backlight/Dimmer
  • Signal Strength Meter
• RF Power Meter
• Instant Channel
  • One touch Instant Channel recalling
• Duplex Capability (from CH01
• CH08 and CH41 - CH48 per channel)
• Group Scan and Priority Channel Watch
• Open Scan
• Scan Channel Memory On/Off separately with Open Scan, Group Scan
  • +12V to +24V DC Power Input
• Rotary Channel Select
• Busy Channel Lock-out Function
  • Roger Beep Function On/Off
• 5 Different Call Tones

• 38 Built-in CTCSS (Continuous Tone Coded Squelch System) and 104 additional DCS (Digital Coded Squelch) codes that are user selectable

• Variable Squelch Level adjust

• Volume Control with Power On/Off Switch

* Refer to p.21 - p.25 for channel information

^ AVS - Automatic Volume Stabilizer detects and manages incoming audio to comparable levels.

Preventive Maintenance

The following system checks should be made every six to twelve months:

• Check the Standing Wave Ratio (SWR).
• Inspect the tightness of all electrical connections.
• Inspect the antenna coaxial cable for wear or breaks on the shielding.
• Inspect the tightness of all screws and other mounting hardware.

Troubleshooting

Should the unit malfunction or perform poorly, follow these procedures: If the transceiver is completely inoperative: Check the power cord and fuse. If there is trouble with receiving: Check the VOLUME control setting. Be sure the SQUELCH is adjusted properly. Possibly the radio is over-squelched.

If there is trouble with transmitting: Check that the transmission line (coaxial cable) is securely connected to the ANTENNA connector. Check that the antenna is fully extended for proper operation. Check that all transmission line (coaxial cable) connections are secure and free of corrosion.

Blackening may occur on the Liquid Crystal Display if the UHF CB Radio has been subjected to extreme high temperature (above 60^ C). This is not a fault. Normal LCD operation resumes when the temperature stabilizes back to standard operating condition ( 0-55^ C).

CHANNEL Uniden TX BUSY INST DUP MON MEM SCAN GS BCL CALL ROGER 88 188 UH5040R VOL SQ ON/OFF MENU ENTER SCAN OS/GS DIM MEM MON DCS/CTCSS DUP MIC 7 10 8 9 2 13 ANT. DC 13.8V DC 27.6V EXT.SP. 14 15 4 5 6 Uniden

1 Liquid Crystal Display (LCD)
2 Rotary Channel Selector
3 On/Off Volume & Squelch
4 Push to Talk (PTT) Switch
5 Call Button
6 Instant Button
7 Menu/Enter - Select Button
8 SCAN - Scan On/Off OS/GS - Open Scan/ Group Scan

9 DIM - Backlight Dimmer
10 MEM - Memory Scan Channels
11 MON - DCS/CTCSS - Monitor and DCS/CTCSS Tone button
12 DUP - Duplex On/Off
13 UHF Antenna Connection
14 External Speaker Jack
15 Power Input (13.8V DC)

1 3 2 4 5 6 7 TX BUSY INST DUP MON MEM SCAN GS BCL CALL ROGER DCSCTCSS S/RF 15 16 14 12 10 9 8 3

1 TX - Transmit
2 MON - Monitor
3 BUSY - Receiving
4 INST - Instant Channel
5 MEM - Memory Scan Channel
6 DCS - Digital Coded Squelch System
7 CTCSS - Continuous Tone Coded Squelch System
8 S/RF - Receive Signal or Transmit RF Power Level Meter

9 188 - DCS/CTCSS Code number
10 88 Channel Number
11 BCL - Busy Channel Lockout
12 ROGER - Roger Beep
13 GS - Group Scan
14 CALL - Call Tone
15 SCAN - Scan Mode
16 DUP - Duplex

Included with your UH5040R Transceiver

Line drawing of a vintage microphone with ventilation grille and stand (no text or symbols)

Standard Microphone Owners Manual Microphone Hanger

Uniden® UH5040R UHF CB Transceiver Owner's MANUAL

Technical line drawing of mechanical components including housing, bolts, and fasteners (no text or symbols)

with Screws/Washers

Technical illustration of a metal bracket with multiple bolt holes and a separate view of bolts (no text or symbols)

Mounting Bracket, Mounting Screws, Washer Stars And Screws

Technical line drawing of a mechanical assembly with bolts and components (no text or symbols)

Slide Mount Bracket, Guide Rails and Screws

Line drawing of a U-shaped cable with two leads and a terminal connector (no text or symbols)

DC Power Cord with fuse

Optional Accessories

• UHF Antenna
• External Speaker
  • DIN Mounting Kit (DMK8990)

Visit the UH5040R page on the website for more information on the availability of optional accessories:

www.uniden.com.au for Australia

How to attach Slide Mount Bracket?

When you unpack the box, ensure that you have the slide mount bracket, guide rails and the screws.

Technical line drawing of a mechanical assembly with exploded view and mounting features (no text or symbols)

Align the guide rails along the side of the base and insert them into the slots provided. Then use the screws to lock them securely in position.

Technical line drawing of an electronic device with ports, buttons, and a display panel (no text or symbols)

Slide the bracket along the guide rails to attach the bracket to the unit.

Mounting the Mic Hanger

The Microphone Hanger comes in two parts. How and where you mount the MIC hanger will determine which parts to use.

Conventional Mounting with Screws

Use the front part of the MIC Hanger only.

Locate a suitable mounting position and mark and drill two 3mm holes.

Fix the MIC Hanger into place with screws.

Front part of the MIC Hanger only. suitable mounting position and mark two 3mm holes. MIC Hanger into place with screws.

Conventional Mounting with Double Sided Tape (not supplied)

High quality Double-Sided tape can be found at good retail stores.

Secure the front and back pieces of the MIC Hanger using the supplied binding screws.

Locate a suitable mounting position.

Apply high quality Double-Sided tape onto the flat area of the MIC Hanger back piece and then press firmly to the mounting position.

Technical line drawing of a mechanical assembly with exploded view (no text or symbols)

Turn on the Power and set the Volume

Turn the unit ON by rotating the volume control clockwise. Set the volume to a desired level.

CHANNEL Uniden UH5040R 01 MENU SCAN DIM MEM MON DUP ON/OFF SQ MIC ENTER OS/GS DCS/CTCSS

Setting the Squelch

Turn the outer ring of the control to adjust the Squelch.

CHANNEL Uniden UH5040R 01 MENU SCAN DIM MEM MON DUP ON/OFF MIC enter OS/GS DCS/CTCSS VOL SQ

NOTE

You must select a channel which is not in use before setting the SQUELCH control. (see below for "Selecting a Channel").

Strong Signals Medium Signals Weak Signals Noise

Think of the squelch control as a gate. If you turn Squelch fully clockwise it raises the 'Squelch gate' so high that no signals get through.

Strong Signals Medium Signals Weak Signals Noise

If you turn the Squelch fully counterclockwise it lowers the 'Squelch Gate' to the extent that all signals get through - weak, medium and strong signals and noise.

Strong Signals Medium Signals Weak Signals Noise

To set the 'Squelch Gate' to the desired level, turn the squelch knob counterclockwise until you hear noise. Then carefully turn the Squelch knob clockwise until the noise fades. Now only strong signals get through.

Monitor

Press [MON] to open the squelch and receive all weak signals. Press [MON] again momentarily to cancel.

CHANNEL Uniden UH5040R 01 VOL SQ ON/OFF MENU SCAN DIM MEM MON DCS/CTCSS ENTER OS/GS

Selecting a Channel

Turn the Rotary Channel Selector to select the desired channel.

CHANNEL Uniden UH5040R 01 MENU SCAN DIM MEM MON DUP ON/OFF VOL SQ MIC ENTER OS/GS DCS/CTCSS

NOTE

For your reference a list of the available channels, corresponding frequencies and guidelines for their use is printed on page 20. For Australia, Channels 05 and 35 are reserved for Emergency Calls.

Set the LCD Dimmer

Press [DIM] to set the LCD backlight dimmer between high and low.

CHANNEL Uniden UH5040R VOL SQ ON/OFF MENU SCAN DIM MEM MON DCS/CTCSS DUP MIC ENTER OS/GS

Transmitting

The UH5040R uses the 80 UHF-CB Channels For your reference a list of the available channels, corresponding frequencies and guidelines for their use and selection is printed on page 20. For Australia, Channels 05 and 35 are reserved for Emergency Calls.

Select the desired channel. Press the microphone's PTT button and speak normally into the microphone. Hold it approx. 7cm from your mouth. Release the PTT button to end the transmission and listen for a reply.

CALL INST PTT- Unidien

Call Function

Press the microphone Call Button. A two second ringing tone will be transmitted. You may select from 5 types of tones (see p.18).

Current regulations require calling tones to be restricted to one transmission per minute. If a second transmission is attempted within one minute then an error tone will sound.

Using Repeater Channels

UHF CB repeaters are used to retransmit or relay your signal. Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions. In normal Simplex operation, your radio transmits on one particular frequency and receives on that same frequency. If there is a barrier that partially blocks your transmitted signal, the probability of another radio receiving the signal is very slim. Hills, tall buildings, metallic structures,...etc tend to act as a screen between radios.

Normal Simplex Operation Transmitting on CH 31 No Signal being Received

Standard Operation without the aid of a Repeater station.

Repeater Station CH 31 CH 01

Operation with the aid of a Repeater Repeater Station (Duplex).

The signal coming from your radio is received by the Repeater Station and the re-transmitted at the same time on another channel. This operation is called "Duplexing".

For example,

CH01 on Duplex Mode will Receive on CH01 but Transmit on CH31

CH02 on Duplex Mode will Receive on CH02 but Transmit on CH32 etc...

If you transmit on CH01 Duplex mode, you are actually transmitting on CH31 the repeater station down-converts your signal and retransmits on CH01.

Operating the UH5040R in Duplex Mode

For this example we are adopting CH01 as the channel being used in your area for repeater use.

Press [DUP] to switch Duplex On. If Duplex is not required - press [DUP] again to switch Duplex off. Only channels 01-08 and channels 41-48 are available for Duplex.

CHANNEL Uniden UH5040R 01 MENU SCAN DIM MEM MON DCS/CTCSS DUP MIC VOL SQ ON/OFF

Check with your local Retailer for information on available repeaters.

Scanning

The UH5040R has a scanning feature that allows you to search for active channels automatically.

Furthermore, the UH5040R is designed to have two types of scanning; Open Scanning (OS) and Group Scanning (GS), to give you flexibility and allow you to use the radio more effectively. Press [SCAN] and Scanning starts. The SCAN icon appears. The scan direction can be changed at any time by rotating the channel selector left or right.

CHANNEL Uniden UH5040R VOL SQ ON/OFF MEN SEN SCAN OS/GS DIM MEM MON DCS/CTCSS DUP MIC

Open Scan (OS) Mode

Allows continuous scanning of all selected channels.

If an active channel is found, scanning will stop on that channel.

If the received signal ceases, the unit will wait 3 seconds for the signal to return, otherwise scanning resumes.

To skip the active channel, press [MEM] momentarily. Scanning resumes. To deactivate SCAN, press [SCAN] or the PTT button on the microphone.

If SCAN is deactivated while on an active channel, the UH5040R will stay on that active channel. If no channels are active, the UH5040R will reinstate the starting channel.

OS Mode is indicated by the absence of the GS icon.

Group Scan (GS) Mode

Allows you to monitor a Priority (Instant) Channel while scanning (Instant Priority channel see p.20).

To use GS Mode Scanning, press [OS/GS]. GS icon appears on the display.

GS Scanning checks the Instant Priority Channel for activity regularly.

If the Priority Channel becomes active the radio will stay on that channel for as long as the signal is present. If the received signal ceases, Priority Scanning continues after 3 seconds.

If scanning stops on a channel which is not a Priority Channel, UH5040R will continue monitoring the Priority Channel for activity while listening to the active one.

To deactivate SCAN, press the [SCAN] button or the PTT button on the microphone.

CHANNEL Uniden UH5040R MENO ENTER SCAN OS/GS DIM MEM MON DCS/CTCSS DUP ON/OFF VOL SQ MIC

If SCAN is deactivated while it is tuned to an active channel, the UH5040R will stay on that active channel.

If none of the channels are active, the UH5040R will reinstate the scan start channel.

If OS/GS Scanning is initiated when there are no channels programmed in OS/GS memory, an error tone will be heard and scanning will not start (see Programming Scan Channels - below).

Programming Scan Channels

Select which Scanning Mode you wish to use - OS or GS.

Select the channel you want to store.

Press [MEM] to store. MEM icon appears and a short tone beep is heard.

To remove the channel from Memory, press [MEM] once more. The MEM icon disappears.

CHANNEL Uniden UH5040R 01 MENU SCAN DIM MEM MON DUP MIC ON/OFF VOL SQ

Selecting the Call tone

Press [MENU] once. Turn the Rotary Channel Selector to change the setting between 1, 2, 3, 4 and 5. Press and hold [MENU] for 3 seconds to store the new setting.

CHANNEL Uniden UH5040R CALL VOL SQ ON/OFF MENU SCAN DIM MEM MON DUP MIC ENTER OS/GS DCS/CTCSS

NOTE

If a button is not pressed within 10 seconds the UH5040R will automatically exit the Menu Mode.

Busy Channel Lockout

If the channel is already in use, you can prevent the UH5040R from transmitting. This is particularly important when using CTCSS.

Press [MENU] twice. Turn the Rotary Channel Selector to display on

Press and hold [MENU] for 3 seconds to store the new setting.

CHANNEL Uniden UH5040R BCL ON VOL SQ ON/OFF MENU ENTER SCAN OS/GS DIM MEM MON DCS/CTCSS DUP MIC

NOTE

If a button is not pressed within 10 seconds the UH5040R will automatically exit the Menu Mode.

Roger Beep

A Roger Beep may be added to the end of transmission.

Press [MENU] 3 times. Turn the Channel Selector to display on

Press and hold [MENU] for 3 seconds to store the new setting.

CHANNEL Uniden UH5040R ROGER ON VOL SQ ON/OFF MENU SCAN DIM MEM MON DUP MIC ENTER OS/GS DCS/CTCSS

NOTE

If a button is not pressed within 10 seconds the UH5040R will automatically exit the Menu Mode.

Programming the Instant Priority Channel

Turn the Rotary Channel Selector to select the Priority Channel you prefer.

Press and hold [INST] button on the microphone for 3 seconds to store the new setting. INST icon appears.

INST Unliven

Recalling the Instant Channel

Momentarily press the [INST] button on the microphone at any time to return to the Instant Channel.

CTCSS (Continuous Tone Coded Squelch System)

Turn the Rotary Channel Selector to the desired channel to use CTCSS.

Press and hold [MON] for 3 seconds. CTCSS icon appears.

Turn the Rotary Channel Selector to select the desired CTCSS code 01 - 38.

Press [MON] once to store the new setting. To turn off CTCSS (or DCS) select the oF code during setting.

CHANNEL Uniden UH5040R 17.01 CTCSS ON/OFF VOL SQ MENU SCAN DIM MEM MON DCS/CTCSS ENTER OS/GS

DCS (Digitally Coded Squelch)

DCS is a digital extension of CTCSS. It provides 104 extra, digitally coded, squelch codes that follow after the 38 CTCSS codes. CTCSS 1-38, followed by DCS 1-99 plus DCS 100-104 (represented by o0-o4 on the display).

Follow the steps for setting a CTCSS code. Turn the Rotary Channel Selector until the DCS codes appear. Press [MON] to set. The DCS icon and code will display.

NOTE

Channels 5 and 35 are used for emergency channels. CTCSS and DCS will not operate on these channels.

NOTE

Always listen on a channel (or observe the receive signal level meter) to ensure it is not already being used before transmitting.

Channels 5 and 35 are used for emergency channels.

CTCSS and DCS will not operate on these channels.

Please follow these guidelines for channel use in Australia:

• Channels 05 and 35 are Emergency Channels.
  • Channel 11 is a Calling Channel.
• Channels 22 and 23 are for telemetry and telecommand applications, channels 61, 62 and 63 are for future use and TX is inhibited on these channels.

General communication is accepted on all other channels with these guidelines:

• Channel 40 - road channel (Australia).
• Channels 01-08 (and 31-38), and Channels 41-48 (and 71-78) are repeater channels.

NOTE

Important information - 80 Channel UHF CB channel expansion

To provide all users additional channel capacity within the UHF CB Band. The ACMA will change the majority of the current wideband 40 channel use to narrowband channel use. This allows for additional channels to be added, up to 80 Channels.

This simply means that the new narrowband radio you have purchased will have more channels than older radios. Please refer to the guidelines above and the channel chart for further channel information.

A list of currently authorised channels can also be obtained from the ACMA website in Australia and the MED website in New Zealand.

Interference / Poor Audio

When a new narrowband radio receives a signal from an older wideband radio the speech may sound loud - however the UH5040R's built-in AVS (Automatic Volume Stabilizer) circuitry will detect and manage incoming audio to comparable levels.

Narrowband radios operating on CH41 - CH80 may encounter interference from a nearby wideband radios transmitting on high power on an adjacent channel (frequency).

When an older wideband radio receives a signal from a new narrowband radio the speech may sound quiet - the wideband radio user simply adjusts their radio volume for best performance.

The above situations are not a fault of the radio but a symptom of mixed wideband and narrowband radios in current use. It is expected that as older wideband radios are phased out this issue will be eliminated.

UHF CB Channels & Frequencies

CH No.	Simplex Mode Transmit / Receive Frequency (MHz)	Duplex Mode Transmit Frequency (MHz)	CH No.	Simplex Mode Transmit / Receive Frequency (MHz)
1 476	425 477.175 (CH31) 2	476.925
2 476	450 477.200 (CH32) 2	476.950 (RX only)
3 476	475 477.225 (CH33) 2	476.975 (RX only)
4 476	500 477.250 (CH34) 2	477.000
5 476	525 477.275 (CH35) 2	477.025
6 476	550 477.300 (CH36) 2	477.050
7 476	575 477.325 (CH37) 2	477.075
8 476	600 477.350 (CH38) 2	477.100
9 476	625 29 477.125
10 476	650 30 477.150
11 476	675 31 477.175
12 476	700 32 477.200
13 476	725 33 477.225
14 476	750 34 477.250
15 476	775 35 477.275
16 476	800 36 477.300
17 476	825 37 477.325
18 476	850 38 477.350
19 476	875 39 477.375
20 476	900 40 477.400

UHF CB Channels & Frequencies

CH No.	Simplex Mode Transmit / Receive Frequency (MHz)	Duplex Mode Transmit Frequency (MHz)	CH No.	Simplex Mode Transmit / Receive Frequency (MHz)
41 47	76.4375 477.1875 (CH 71) 61			future use476.9375 (RX only)
42 47	76.4625 477.2125 (CH 72) 62			future use476.9625 (RX only)
43 47	76.4875 477.2375 (CH 73) 63			future use476.9625 (RX only)
44 47	76.5125 477.2625 (CH 74) 64 477.0125
45 47	76.5375 477.2875 (CH 75) 65 477.0375
46 47	76.5625 477.3125 (CH 76) 66 477.0625
47 47	76.5875 477.3375 (CH 77) 67 477.0875
48 47	76.6125 477.3625 (CH 78) 68 477.1125
49 47	76.6375 69 477.1375
50 47	76.6625 70 477.1625
51 47	76.6875 71 477.1875
52 47	76.7125 72 477.2125
53 47	76.7375 73 477.2375
54 47	76.7625 74 477.2625
55 47	76.7875 75 477.2875
56 47	76.8125 76 477.3125
57 47	76.8375 77 477.3375
58 47	76.8625 78 477.3625
59 47	76.8875 79 477.3875
60 47	76.9125 80 477.4125

CTCSS codes table

Code No.	Frequency (Hz)	Code No.	F	frequency (Hz)
“oF” OFF 20 131.8
1 67.0 21	136.5
2 71.9 22	141.3
3 74.4 23	146.2
4 77.0 24	151.4
5 79.7 25	156.7
6 82.5 26	162.2
7 85.4 27	167.9
8 88.5 28	173.8
9 91.5 29	179.9
10 94.8 30	186.2
11 97.4 31	192.8
12 100.0	32 203.5
13 103.5	33 210.7
14 107.2	34 218.1
15 110.9	35 225.7
16 114.8	36 223.6
17 118.8	37 241.8
18 123.0	38 250.3
19 127.3
Code No.	DCS Code (Octal)	Code No.	DCS Code (Octal)	Code No.	DCS Code (Octal)
1 023 36	223 71 445
2 025 37	225 72 446
3 026 38	226 73 452
4 031 39	243 74 454
5 032 40	244 75 455
6 036 41	245 76 462
7 043 42	246 77 464
8 047 43	251 78 465
9 051 44	252 79 466
10 053 45	255 80 503
11 054 46	261 81 506
12 065 47	263 82 516
13 071 48	265 83 523
14 072 49	266 84 526
15 073 50	271 85 532
16 074 51	274 86 546
17 114 52	306 87 565
18 115 53	311 88 606
19 116 54	315 89 612
20 122 55	325 90 624
21 125 56	331 91 627
22 131 57	332 92 631
23 132 58	343 93 632
24 134 59	346 94 654
25 143 60	351 95 662
26 145 61	356 96 664
27 152 62	364 97 703
28 155 63	365 98 712
29 156 64	371 99 723
30 162 65	411 100 731
31 165 66	412 101 732
32 172 67	413 102 734
33 174 68	423 103 743
34 205 69	431 104 754
35 212 70	432

UNIDEN UH5040R UHF CB Transceiver

IMPORTANT: Satisfactory evidence of the original purchase is required for warranty service

Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below.

Warrantor: The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 ("Uniden Aust").

Terms of Warranty: Uniden Aust warrants to the original retail purchaser only that the UH5040R (“the Product”), will be free from defects in materials and craftsmanship for the duration of the warranty period, subject to the limitations and exclusions set out below.

Warranty period: This warranty to the original retail purchaser is only valid in the original country of purchase for a Product first purchased either in Australia or New Zealand and will expire, as indicated below, from the date of original retail sale.

Product 5 Years
Accessories 1 Year

If a warranty claim is made, this warranty will not apply if the Product is found by Uniden to be:

(A) Damaged or not maintained in a reasonable manner or as recommended in the relevant Uniden Owner's Manual;
(B) Modified, altered or used as part of any conversion kits, subassemblies or any configurations not sold by Uniden Aust;
(C) Improperly installed contrary to instructions contained in the relevant Owner's Manual
(D) Repaired by someone other than an authorized Uniden Repair Agent in relation to a defect or malfunction covered by this warranty; or
(E) Used in conjunction with any equipment, parts or a system not manufactured by Uniden.

Parts Covered: This warranty covers the Product and included accessories.

User-generated Data: This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation phone numbers, addresses and images) that may be stored on your Product.

Statement of Remedy: If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either repair the defect or replace the Product without any charge for parts or service. This warranty does not include any reimbursement or payment of any consequential damages claimed to arise from a Product's failure to comply with the warranty.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

This warranty is in addition to and sits alongside your rights under either the COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER GUARANTEES ACT (New Zealand) as the case may be, none of which can be excluded.

Procedure for obtaining warranty service: Depending on the country in which the Product was first purchased, if you believe that your Product does not conform with this warranty, you should deliver the Product, together with satisfactory evidence of your original purchase (such as a legible copy of the sales docket) to Uniden. Please refer to the Uniden website for address details. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty claim. Prior to delivery, we recommend that you make a backup copy of any phone numbers, images or other data stored on your Product, in case it is lost or damaged during warranty service.

UNIDEN AUSTRALIA PTY LTD

Phone: [phone]

Email: [e-mail]

THANK YOU FOR BUYING A UNIDEN PRODUCT.

Uniden®

© 2018 Uniden Australia Pty Limited. Printed in Vietnam. U01UT989ZZZ(0)