KG71 - Range hood CDA - Free user manual and instructions

Product Type	Range Hood
Brand	CDA
Model	KG71
Dimensions (W x D x H)	60 cm x 50 cm x 30 cm (approx.)
Mounting Type	Under cabinet / Wall-mounted
Extraction Method	Ducted or Recirculating
Maximum Extraction Rate	350 m³/h (approx.)
Noise Level	55 dB(A) (approx.)
Number of Fan Speeds	3
Lighting	2 x LED lights (replaceable)
Filter Type	Aluminum grease filter (washable)
Control Type	Push buttons
Energy Class	A+ (approx.)
Annual Energy Consumption	30 kWh/a (approx.)
Power Supply	220-240 V, 50 Hz
Motor Power	150 W
Weight	12 kg (approx.)
Duct Diameter	150 mm
Cleaning	Wipe with damp cloth; wash grease filter monthly
Safety Features	Overheat protection; auto shut-off when lifted
Spare Parts Available	Yes: filters, LED bulbs, control buttons
Installation Manual	Included with product
Warranty	2 years (manufacturer warranty)

Frequently Asked Questions - KG71 CDA

How do I install the CDA KG71 range hood?

How often should I clean the grease filter?

Can I use the hood without ducting?

Why is my range hood noisy?

How do I replace the LED light?

What should I do if the hood stops working?

What is the minimum distance from cooktop?

How do I change the fan speed?

Can I paint the hood?

Where can I find spare parts?

USER MANUAL KG71 CDA

Taking care of your sink

Your CDA sink is manufactured using material developed specifically to withstand the rigours of everyday kitchen use. However, we advise you to follow these precautions to keep the sink in pristine condition:

• Do not use a plastic washing-up bowl in the sink as grit and other particles may become embedded in the bowl and scratch or erode the sink surface. CDA specifically recommend the use of wire sink-baskets and drainer-racks to help protect your sink. Take care to not cut the plastic coating on these accessories with sharp cutlery or the edges of pans, etc.
• Do not use neat bleach or other harsh cleaning agents on the metal sink waste as this may cause tarnishing. This is especially important if the waste is of the brass/brass finish type.
• Avoid dropping heavy or sharp objects into the sink as they may scratch or damage the surface.
• The surface of the sink can be affected by certain chemicals e.g. neat bleach, nail polish remover, paint stripper, solvents, brush cleaner and insecticides. If any of these substances come into contact with the sink, wipe off immediately with a dry cloth, wash with mild detergent and rinse with water.
• Do not use abrasive liquids, powders or steel pads to clean the sink as they will damage the sink surface and make it more susceptible to staining. The sink may be cleaned with a dilute bleach solution.
• Do not place very hot objects directly on the sink, place them on a special surface (board) made from wood or heat-proof plastic, etc.
• In hard-water areas, a limescale deposit may build up on the sink. The limescale may become stained by coloured foods such as coffee or red wine. If this occurs, we recommend use of a mild limescale remover.

• Particularly stubborn organic stains can be removed effectively by soaking the sink in a biological washing-powder solution, dishwasher powder solution or diluted bleach.
- If the sink comes into contact with acidic materials, rinse immediately with plenty of water and wipe with a soft dry cloth.
- Do not leave rusty objects in contact with the sink. Rust can cause staining, cracking or even permanent damage to the sink surface.
- To avoid staining of the surface do not leave food or other materials with corrosive properties such as juices, salt, vinegar, mustard etc. on the sink for a long time.
- After using the sink, rinse it clean with warm soapy water and rinse with clean water before wiping dry.
• During installation, protect from scratches, scuffs and other damage.
• Do not overtighten or strain plumbing fittings.
- The moulding and edges of the sink must be absolutely level so water flows off the drainer.

To cut out the worktop:

• Place the sink upside-down on the worktop where it will be mounted.
  • Draw the perimeter of the sink on the worktop with a pencil.
• Remove the sink and draw a dotted line, 1 cm inside the perimeter.
  • Make the cut out with suitable tools along the dotted line.

Inserting the sink in the hole of the working surface:

- Inserting the sink in the hole of the working surface. Our sinks are not equipped with pre-mounted hooks, but the hooks are provided inside the sink's package and they should be installed on the sink by the installer.

• Place the special included sealant along the whole perimeter of the sink that will be in contact with the surface.
• Place the sink in the hole and make sure it is centered, then lock the hooks with the adjustment screws from the center outwards in crisscross order.

Drain connection

• Follow the instructions attached to the drain fittings.

This guarantee is valid providing that

• The product has been installed by a suitably qualified person.
• Installation has been carried out in accordance with instructions and current legislation.
• Proof of purchase can be produced.
• The product has been used for domestic purposes only.
- The product has not been tampered with or repair attempted or modified by any unauthorised person.
- All products have been installed in accordance with WRAS regulations and local water bye-laws

This guarantee does not cover

• Damage by misuse, neglect or transit.
• Use of parts not used or recommended by CDA.
• Routine maintenance, general wear & tear and installation faults.
• Products used for commercial or professional purposes.

Your sink is guaranteed against defects in materials and/or workmanship for 5 years. At the discretion of CDA, should a fault arise the sink may be repaired or replaced and agreed refitting may be reimbursed on receipt on a faulty sink/part, once they have been inspected and deemed faulty.

E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the right to change specifications without prior notice.

Please contact our Customer Care Department for Service on the details below

Customer Care Department

The CoUp Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY

T:01949 862 012 F:01949 862 003 E: [e-mail]