S3501 N3 - Steam cleaner SHARK - Free user manual and instructions

USER MANUAL S3501 N3 SHARK

Close-up of a dark object on a textured surface against a purple background (no text or symbols visible)

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

For Household Use Only

WHEN USING YOUR SHARK STEAM POCKET® MOP, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING YOUR STEAM POCKET® MOP.

DANGER OF SCALDING.

Please use caution when using the Steam Pocket® Mop. The steam emitted from the Steam Pocket® Mop is very hot.

POLARIZED PLUG:

This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

WARNING: To reduce the risk of fire, electric shock or injury:

1. Use the system only for its intended use.

2. DO NOT use outdoors.

3. DO NOT leave the appliance unattended when plugged in. Always unplug the power cord from the electrical outlet when not in use and before servicing.

4. DO NOT allow the appliance to be used by children. Close attention is necessary when used by or near children, pets or plants.

5. Use only as described in this manual.

6. Use only manufacturer's recommended accessories.

7. DO NOT operate the appliance with a damaged plug or cord, or if the unit has been dropped or damaged. To avoid the risk of electric shock, do not disassemble or attempt to repair the appliance on your own. Return the appliance to EURO-PRO Operating LLC (see warranty) for examination and repair. Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons when the appliance is used.

8. To protect against a risk of electric shock, DO NOT immerse the Steam Pocket® Mop into water or any other liquids.

9. DO NOT handle plug or Steam Pocket® Mop with wet hands or operate appliance without shoes.

10. DO NOT pull or carry by power cord, use power cord as handle, close a door on the power cord, or pull the power cord around sharp edges or corners. Keep power cord away from heated surfaces.

11. DO NOT unplug by pulling on power cord. To unplug, grasp the plug not the power cord. Do not use extension cords or outlets with inadequate current carrying capacity.

12. DO NOT put any objects into openings. Do not use with any opening blocked.

13. DO NOT put hands or feet under the Steam Pocket® Mop. Unit gets very hot.

14. Use ONLY on flat, horizontal surfaces. Do not use on walls, counters or windows.

15. DO NOT use on leather, wax polished furniture or floors, synthetic fabrics, velvet or other delicate, steam sensitive materials.

16. DO NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance as this may damage the unit or make it unsafe for use. If you live in a hard water area, we recommend using distilled water in your Steam Pocket® Mop.

17. When in use, NEVER turn the appliance over or on its side. NEVER DIRECT STEAm tOWARDS PEOPLE, ANIMALS OR PLANTs.

18. NEVER LEAVE tHE StEAm POCKET® mOP IN ONE SPOT ON ANY SURFACE FOR ANY PERIOD OF tImE WHEN MICROFIBER POCKET IS ATTACHED.

19. Carefully remove the microfiber pocket immediately after you have unplugged and allowed the Steam Pocket® Mop to cool.

20. When cleaning the Steam Pocket® Mop, unplug the power cord from the electrical outlet and clean with a dry or damp cloth. Do not pour water or use alcohol, benzene or paint thinner on the unit.

21. Extreme caution should be exercised when using this appliance to clean stairs.

22. Never use Steam Pocket® Mop without microfiber pocket attached.

23. Not for space heating purposes.

24. Keep your work area well lit.

25. Store Steam Pocket® Mop indoors in a cool, dry place.

26. To avoid circuit overload, do not operate another appliance on the same socket (circuit) as the steam cleaner.

27. If an extension cord is absolutely necessary, an extension cord rated a minimum of 15 ampere, 14 gage cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange cord so that it cannot be pulled or tripped over.

28. DO NOT leave your Steam Pocket ® Mop unattended when the system is connected to a power supply/electrical outlet.

29. DO NOT store unit with damp/wet microfiber Steam Pocket® pocket attached. Never leave the Steam Pocket® Mop in one spot on any surface for any period of time with a damp or wet microfiber Steam Pocket® pocket attached as this will damage your floors.

30. Always unplug and allow the Steam Pocket® Mop to cool before removing or changing mop heads.

WARNING

Your Steam Pocket® Mop is designed to clean hard floor surfaces that will withstand high heat. Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax or some no wax floors, the sheen may be removed by the heat and steam action. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check the use and care instructions from the floor manufacturer.

Quick Start

Diagram illustrating the step-by-step installation of a vacuum cleaner, showing hand positioning and assembly process.

When assembling your Steam Pocket® Mop there may be a little water in or around the water tank. This is because we test all our Steam Pocket ® Mops 100% before you buy them, so you get a quality Shark® Steam Pocket® Mop.

Illustration of hands using a tool to cut a component, with a purple arrow indicating the process (no text or symbols present)

Line drawing of a hand using a tool to adjust or install an air mask (no text or symbols present)

ASSEMBLE

1 Insert the mop handle into the pump actuator (the tube that leads to the tank). Push the mop handle and pump actuator together in until you hear it click into place.

2 Select a cleaning pad. Fit one side of the pocket onto the head first, then using the lavender loop, pull the pocket over the head. Attach the quick fasteners on the top of the pocket to secure in place.

3 Snap the mop head into the base to secure it. Press the release button to exchange mop heads.

FILL

4 Lay the mop on the floor or on a counter top and remove the water tank cap by turning counter clockwise. Fill the water tank using the filling flask. Do not overfill the water tank. Replace the water cap and tighten.

IMPORTANT: Make sure your floors are sealed. Before using the Steam Pocket ® Mop consult page 4 for more information.

QUICK TIP: For easier pushing and pulling, extend the handle length. 5 6

PREPARE

5 For your comfort, you can adjust the height of the mop. Just lift the latch on the tube 90 degrees to the open position. Holding the handle, extend the tube to the height that's right for you and then close latch to locked position.
6 Plug in mop and wait 30 seconds or less for the mop to heat up. Pump the handle of the mop by pushing downward about 10 to 12 times to create steam.

NOTE: Steam is created automatically when you start mopping.

DIRT CAN'T HIDE ON EITHER SIDE! All new design allows for optimal cleaning! When one side of the pocket gets dirty, just turn the mop head over and clean with the other side of the pocket.

Line drawing of a person using a walking pushper to lift a device, with purple motion arrows indicating rotation (no text or symbols)

OTE: Do not leave your Steam Pocket® Mop unattended during use.

IMPORTANT: Never leave the Steam Pocket® Mop in one spot for any period of time with a damp or wet microfiber Steam Pocket® attached as this will damage your floors.

This manual covers model number: S3501 N3 13

TECHNICAL SPECIFICATIONS

Voltage: 120V., 60Hz.

Power: 1200 Watts

Water Capacity: 450 ml (15 oz.)

Contents

Thank you for purchasing the Shark® Steam Pocket® Mop.

Getting Started ....2

Using Your Steam Pocket® Mop ......6

Care of Your Steam Pocket® Mop....8

Ordering Replacement Parts ....10

Troubleshooting Guide....11

Warranty and Registration 13

Getting Started

When assembling your Steam Pocket ^® Mop there may be a little water in or around the water tank. This is because we test all our Steam Pocket ^® Mops 100% before you buy them, so you get a quality Shark ^® Steam Pocket ^® Mop.

Two simple line drawings: top shows a mechanical component with labeled points (a and b), bottom shows a bucket filled with liquid (no text or symbols)

a 2 All Purpose Cleaning Pads

b Filling Flask

e c d f g h i j

c Quick Release Swivel Cord Wrap

d Cord Clips

e Mop Handle

f Telescopic Handle Latch

g Water Tank Viewing Window

h Power-On Blue Light

i Water Tank Cap

j Rectangle Mop Head

Diagram illustrating the use of a vacuum cleaner with labeled components and directional arrows indicating motion.

Diagram showing a hand using a tool to adjust or install a device, with a numbered step and directional arrow indicating process flow.

IMPORTANT: Always make sure the mop is UNPLUGGED from the wall when not in use. Never fill the mop, attach the mop head, change or remove the microfiber pocket when the mop is plugged into the wall. To prolong the life of your Shark® Pro Steam Pocket® Mop, we recommend using distilled water. Make sure you only add water to the tank. Chemicals or cleaning solution may damage the appliance and could be unsafe for you and your family.

ASSEMBLE

1 Insert the mop handle into the pump actuator (the tube that leads to the tank). Push the mop handle and pump actuator together in until you hear it click into place.

2 Select a cleaning pad. Fit one side of the pocket onto the head first, then using the lavender loop, pull the pocket over the head. Attach the quick fasteners on the top of the pocket to secure in place.

Getting Started

Diagram illustrating the step-by-step installation of a hairless vacuum cleaner, showing disassembly and assembly steps.

Calcium and mineral deposits can build up and impact the performance of your steam mop over time. To extend the life of your product we recommend that you use distilled water or Shark®'s Water Filtration Bottle. Visit www.sharkclean.com to order.

Illustration of a medical procedure involving a tool and tubing, no text or symbols present

3 Snap the mop head into the mop body until you hear it latch into place. Press the release button to exchange mop heads.
4 Turn the water tank cap counter clockwise and remove from the tank.

Use the filling flask and pour water into the tank. Please do not overfill. Replace the cap on the water tank by turning clockwise and tightening.

IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax or some no wax floors, the sheen may be removed by the heat and steam action. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We recommend that you check the use and care instructions from the floor manufacturer.

5 1 1

5 For your comfort, you can adjust the height of the mop. Just lift the latch on the tube 90 degrees to the open position. Holding the handle, extend the tube to the height that's right for you and then close latch to locked position.

QUICK TIP: For easier pushing and pulling, extend the handle length.

Using Your Steam Pocket® Mop

IMPORTANT: Do not use the mop without attaching a microfiber pocket and adding water to the tank first. When you are using the mop for the first time, it might take longer than the normal 30 seconds to start steaming. Just pump the handle a few times in a downward motion to prime the pump.

Illustration showing two steps of hairpin usage: one with a hand holding a cord, the other with a cord being inserted into a clip.

Diagram illustrating a person using a vacuum cleaner with labeled steps and directional arrows indicating movement.

NOTE: Make sure the floors are swept or vacuumed before using the Steam Pocket ® Mop.

1 Pull and twist the quick release cord holder to unwrap the power cord completely.

Plug into an electrical outlet The power "On" light will turn blue, it takes approximately 30 seconds for the mop to heat up and the steam to be ready.

2 Pump the handle a few times in a downward motion. This pumping action will release steam as you mop and allows you to customize the amount of steam you want. Begin mopping with a forward and backward motion. The natural motion of mopping will produce steam.

3

3 When one side of the microfiber pocket gets dirty, just flip the mop head and you can quickly start using the other side.

IMPORTANT: Please wait 3-5 minutes for the Steam Pocket® Mop to cool before switching the mop head or the microfiber Steam Pocket®.

4 When the water tank is empty, the Steam Pocket® Mop will stop producing steam. You can refill the water tank at any time as long as the mop is unplugged from the outlet. Follow the instructions from page 4.

IMPORTANT: Never leave the Steam Pocket ® Mop with a damp/wet microfiber pocket on any floor surface for any amount of time as this may damage the floor.

Care of Your Steam Pocket® Mop

AFTER USE AND STORAGE

1 When you have finished using the Steam Pocket ^® Mop, unplug the cord from the outlet and let the unit cool 2-3 minutes. Release steam by pumping the handle several times before removing the microfiber Steam Pocket ^® from the mop head.

Diagram showing a hand using a pliers to adjust a device, with numbered annotation indicating step 2.

Line drawing of a steam gun with handle and control panel (no text or symbols)

2 Remove the microfiber Steam Pocket® by releasing the quick fasteners and using the lavender loop on the side of the pocket to pull off. Avoid contact with the hot pocket or dirt. Then empty the water tank.

3 To store the Shark ^® Steam Pocket ^® Mop hanging up; first remove the head (after it has cooled and the steam has been released) then hang on a large hook.

NOTE: If you want to store it standing upright, then make sure it's leaning against a wall for added support and safety. Always store your Steam Pocket® Mop with the microfiber Steam Pocket® removed, away from children or high traffic areas.

Pure mechanical diagram showing a U-shaped component with four square holes and flanges, no text or symbols present.

Illustration of a hand using scissors to cut a piece of paper (no text or symbols present)

1

CARE OF YOUR MICROFIBER CLEANING PAD

1 We recommend washing your microfiber Steam Pockets® separately from other fabrics to avoid picking up lint.

Only use liquid detergent. (No powder detergent) Do not use any fabric softeners or bleach.

Line dry or dry on a low dryer setting.

2 If there are loose threads on the pocket carefully cut the thread with scissors. Do not pull on them or cut at the base.

DECALCIFYING YOUR STEAM MOP

Calcium and mineral deposits can build up and impact the performance of your steam mop over time.

To extend the life of your product we recommend that you use distilled water or Shark®'s Water Filtration Bottle.

Visit www.SharkClean.com to order.

Ordering Replacement Parts

Simple line drawing of a symmetrical object with four square holes and a central U-shaped feature, no text or symbols present.

Purple textured fabric pattern with white square cutouts and arrow indicators (no text or symbols)

Line drawing of a mechanical component with grid pattern and a numbered label (3), no readable text or symbols present.

Technical line drawing of a mechanical device with no visible text or symbols

Simple line drawing of a rectangular tray or container with no text or symbols

ORDERING REPLACEMENT PARTS

To order additional parts and accessories, feel free to contact us at www.sharkclean.com or call 1-800-798-7398.

PART PART NO.

1 (2) All-Purpose Cleaning Pads XT3501
2 (2) Steam Duster Cleaning Pads XT3501SD
3 Rectangle Mop Head 1024SO
4 Triangle Mop Head 1025SO
5 Carpet Glider XCG3501CON

PROBLEM POSSIBLE REASONS & SOLUTIONS

The Steam Pocket®Mop will not turn on.	Your Steam Pocket® Mop should be securely plugged into an electrical outlet only.Check your fuse or breaker.If your unit still doesn’t work, give us a call 1-800-798-7398.
Steam Pocket® Mop will not make steam.	Prime the pump, see page 6 for more information.Is there water in the water tank? If not, add water to your Steam Pocket® Mop following the instructions.
Steam Pocket® Mop leaves water on the floor.	Check to see if your microfiber Steam Pocket® is too wet. We recommend you unplug the Steam Pocket® Mop and change the microfiber Steam Pocket®.Make sure the steam pocket is attached correctly.
Steam Pocket® Mop is hard to push.	Make sure the steam pocket is attached correctly.Check to see if your pocket is excessively dirty.Try increasing the height of the pole for better leverage.
Floors are cloudy, streaky or spotty after steaming.	The microfiber pocket might be dirty. Flip or change the pocket.If you washed the pocket with powder detergent then the pocket might be ruined.If you are cleaning in a kitchen area where there might be a build-up of grease then use a degreasing agent such as an all-purpose cleaner or dish soap and paper towels to clean the area first.You might have left the mop in the same spot for too long.Do you have hard water? If you do you, we recommend switching to distilled water.

Notes

EURO-PRO

ONE (1) YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid. For Customer Service support, call 1 [phone] or visit our website www.sharkclean.com.

If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and \$ 19.95 to cover the cost of return shipping and handling must be included. *

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.

Product Registration

Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.

The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.

EURO-PRO Operating LLC

U.S.: Newton, MA 02459

Canada: Ville St. Laurent, Québec H4S 1A7

1-800-798-7398

www.sharkclean.com

Copyright © Euro-Pro Operating LLC 2014

Printed in China

Illustrations may differ from actual product.

S3501.N3.13.E.140107.4