32767 - Câble AV Lindy - Free user manual and instructions

USER MANUAL 32767 Lindy

Thank you for purchasing this product from the LINDY CAT5/6 VGA & Audio Extender range. This VGA Extender range consists of three transmitter units and three receivers which can be mixed and matched according to your requirements. Depending on the required video resolution, transmission distances of up to 300m, are possible making the VGA & Audio Extender System an ideal choice for digital signage, public display and video distribution installations.

The complete product range can be easily combined and expanded to suit a variety of applications through the use of low cost Cat5/6 cable. Taking advantage of Cat5/6 cable, installation is simplified and particularly cost effective whether you are splitting, extending or distributing VGA and audio signals.

Installation Notes

1. Before connecting any devices, please ensure all equipment is powered off
2. Proceed by connecting the transmitter module to your VGA source. Depending on the transmitter module purchased this may either be by direct connection or by using optional male to female VGA cables
3. Please note that transmitter module No. 32754 is provided with a special combined VGA + Audio and USB cable for connection to your computers VGA card. If you have purchased No. 32762 then you will need to purchase a suitable male to female VGA cable
4. If you intend to connect a sound source and speakers then use a standard 3.5mm jack male to male cable between your sound card and the transmitter module. Please note that No. 32754 and 32764 have a short audio cable with a 3.5mm jack plug already attached for connection to your sound card and speakers
5. Connect the transmitter and receiver modules using a suitable Cat5/6 network patch cable of the required length. This may be a loose cable or you can make use of your cable infrastructure via wall plates and patch panels. Please note the extender system requires a point to point connection and must not be connected to any active network equipment
6. Connect a local VGA monitor and speakers to the transmitter module if required (No. 32762, No. 32764, No. 32767). Locate the receiver unit and connect the remote VGA monitor and, speakers if required.
7. Check all connections have been made correctly and apply power to the transmitter and receiver modules. Once completed check for correct displays on both the local and remote monitors.

Typical applications

Choose any of the following configurations depending on the number of displays and the operating distance required. Choose from a single port point to point extender or extend and display any VGA signal to 8 monitors. Additional receiver modules can be purchased as your system expands. Receiver unit No. 32763 and transmitter unit No. 32765 are fitted with a convenient magnetic base allowing easy installation to any metal surface.

graph TD
    A["Cat5/6 or higher cable"] --> B["Switch"]
    C["Up to 8 Receiver modules can be connected when using No. 32762 8 Port Transmitter"] --> B
    D["Switch"] --> E["Switch"]
    F["AV Cat.5 Extender Splitter/Transmitter"] --> E
    G["Switch"] --> H["Switch"]
    I["Switch"] --> J["Switch"]
    K["Switch"] --> L["Switch"]
    M["Switch"] --> N["Switch"]
    O["Switch"] --> P["Switch"]
    Q["Switch"] --> R["Switch"]
    S["Switch"] --> T["Switch"]
    U["Switch"] --> V["Switch"]
    W["Switch"] --> X["Switch"]
    Y["Switch"] --> Z["Switch"]
    AA["Switch"] --> AB["Switch"]
    AC["Switch"] --> AD["Switch"]
    AE["Switch"] --> AF["Switch"]
    AG["Switch"] --> AH["Switch"]
    AI["Switch"] --> AJ["Switch"]
    AK["Switch"] --> AL["Switch"]
    AM["Switch"] --> AN["Switch"]
    AO["Switch"] --> AP["Switch"]
    AQ["Switch"] --> AR["Switch"]
    AS["Switch"] --> AT["Switch"]
    AU["Switch"] --> AV["Switch"]
    AW["Switch"] --> AX["Switch"]
    AY["Up to 150m using Receiver No. 32764"] --> AC
    AZ["Up to 250m using Receiver No. 32765"] --> AD
    BA["Up to 300m using Receiver No. 32767"] --> AE
    BB["Extend one VGA monitor & Speakers"] --> AC
    BC["Extend up to eight VGA monitors & Speakers"] --> AD

1-Port VGA & Audio Transmitter 150m No. 32754

1. Audio input from sound card
2. USB power cable
3. VGA input from video card
4. RJ-45 output to receiver via Cat5/6 cable

Diagram of a blue DVI cable with labeled pins and connectors, showing connections to ports 1, 2, and 3.

1-Port VGA & Audio Receiver 150m No. 32764

1. Audio output to remote speakers
2. Power adapter input with focus control
3. VGA output to remote monitor
4. RJ-45 input from transmitter via Cat5/6 cable

Diagram showing three connected audio devices with labeled pins: 1, 2, and 3 pointing to their connectors.

Key Features:

Compact transmitter and receiver modules allow VGA and Audio signals to be extended over long distances using low cost Cat5/6 cables. The transmitter unit attaches to your VGA output and sound card, and is powered by the computer's USB port. The receiver unit attaches to your remote VGA monitor and speakers and features a focus control for adjusting the picture quality.

• Compact AV Transmitter and Receiver modules
  • Transmitter module powered from USB port
• Extends VGA + Audio over Cat5/6 cable up to 150m
  • Built in focus control for adjusting picture quality (receiver)
  • H. Sync and V. Sync activity indicators
  • Supports DDC2B

1-Port VGA & Audio Transmitter 250m No. 32763

1. Power status indicator
2. Power adaptor input (5 Volts DC, 1.2Amp) this is optional
3. VGA output to local monitor
4. Audio output to local speakers
5. VGA + Audio and power input via combined VGA + Audio and USB power cable
6. RJ-45 output to receiver via Cat5/6 cable
7. H. Sync and V. Sync activity indicators (RJ-45 port)

NBV NV Cal.5 Extended Transmitter Power VGA OUT AUDIO VGA + AUDIO IN SYSTEM LINK ① ⑦ ② ③ ④ ⑤ ⑥

1-Port VGA & Audio Receiver 250m No. 32765

1. Power status indicator
2. Power adapter input (5 Volts DC, 1.2Amp)
3. VGA output to remote monitor
4. Audio output to remote speakers
5. Gain and focus controls for adjusting picture quality
6. RJ-45 input from transmitter via Cat5/6 cable
7. H. Sync and V. Sync activity indicators (RJ-45 port)

NV Data Explorer Interface Power VGA OUT AUDIO OUT GAIN FOCUS SYSTEM LINK ① ⑦ ② ③ ④ ⑤ ⑥

Key Features:

Compact single port transmitter and receiver modules allow VGA and Audio signals to be extended over long distances using low cost Cat5/6 cables. The transmitter unit attaches to your VGA output and sound card and is powered by the computers USB port.

• Compact single port AV extender
• Extends VGA + Audio signals over Cat5/6 cable up to 250m
  • Focus and gain controls for adjusting picture quality
  • Supports DDC2B

8-Port VGA & Audio Extender 250m No. 32762 (Transmitter)

1. VGA activity indicator
2. Power status indicator
3. Power adaptor input (5 Volts DC, 1.2Amp)
4. VGA input from video card
5. Audio input from sound card
6. VGA output to local monitor
7. Audio output to local speakers
8. VGA + Audio outputs to receivers via Cat5/6 cable

Key Features:

Compact eight port transmitter module allows multiple VGA and Audio signals to be extended over long distances using low cost Cat5/6 cables.

• Compact eight port AV splitter/transmitter module
• Extends multiple VGA + Audio signals over Cat5/6 cable up to 250m
  • Supports DDC2B
• May be cascaded to allow extender modules to be located at intervals of 250m

VGA & Audio Receiver 300m No. 32767

1. Power status indicator
2. Power adapter input (5 Volts DC, 1.2Amp)
3. VGA output to remote monitor
4. Audio output to remote speakers
5. Focus control for adjusting picture sharpness

6. Gain controls for adjusting signal gain

7. RJ-45 input from transmitter via Cat5/6 cable and H. Sync and V. Sync activity indicators

8. Red, green and blue controls for adjusting picture colours and skew

AV Data Exchanger Receiver Pro Power DNDY® ① ② ③ ④ ⑤ ⑥ ⑦ ⑧

Key Features:

Compact single port transmitter and receiver modules allow VGA and Audio signals to be extended over long distances using low cost Cat5/6 cables with high resolutions (1920x1200). The transmitter unit attaches to your VGA output and sound card and is powered by the computers USB port.

• Compact single port AV extender
• Extends VGA + Audio signals over Cat5/6 cable up to 300m in 1920x1200
• Focus and gain controls for adjusting picture quality
• Red, green and blue controls for adjusting picture colours and skew
• Supports DDC2B

CE Certification

This equipment complies with the requirements relating to electromagnetic compatibility, EN55022/EN55024 class B for IEC/EN61000-4-2/3 the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility.

FCC Certification

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced technician for help

You are cautioned that changes or modification not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products

United Kingdom

In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.

Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency.

Germany

2 ^nd Edition September 2014