Trike Big Wheeler 565D - Lawn mower GUDE - Free user manual and instructions

Product type	Riding lawn mower
Brand	Güde
Model	Trike Big Wheeler 565D
Dimensions (L x W x H)	2500 x 1500 x 1200 mm
Weight	300 kg
Engine type	Diesel
Engine displacement	565 cm³
Engine power	14 kW
Transmission type	Hydrostatic
Cutting width	100 cm
Cutting height	30 - 100 mm (adjustable)
Grass catcher capacity	300 L
Forward speed	0 - 10 km/h
Starting type	Electric
Number of wheels	3 (Trike)
Safety system	Operator presence switch
Regular maintenance	Engine oil change, air filter, spark plug
Cleaning	Clean the deck and blades after each use
Spare parts available	Blades, belts, filters, spark plugs
Repairability	Repairability index: 8/10

Frequently Asked Questions - Trike Big Wheeler 565D GUDE

How to start the Trike Big Wheeler 565D mower?

Make sure the fuel tank is full (diesel) and the battery is charged. Sit on the seat, engage the parking brake, turn the ignition key and wait for preheating (indicator light turns off). Then, turn the key to start the engine.

What engine oil to use?

Use 15W-40 or 10W-30 engine oil depending on ambient temperature. Check the manual for the exact volume (about 3 liters).

How to adjust the cutting height?

The cutting height is adjusted via a central lever (or pins) on each wheel. Turn the lever to select the desired height between 30 and 100 mm. Make sure both sides are at the same height.

The mower won't start, what to do?

First check that the operator presence switch is active (you must be seated). Check the battery, fuel level and fuses. If preheating does not work, the glow plugs may be faulty.

When and how to change the engine oil?

Change the engine oil after the first 50 hours, then every 100 hours or once a year. Place a pan under the crankcase, unscrew the drain plug and let the warm oil drain. Replace the plug and fill with new oil.

How to clean the cutting deck?

After each use, lift the cover and remove grass debris with a water jet or scraper. Avoid directing water towards the engine. Dry thoroughly before storing.

What type of battery is used?

A 12V battery, usually 60 Ah or 90 Ah. If the battery is flat, recharge it with a suitable charger or replace it.

How to replace the cutting blades?

Disconnect the spark plug for safety. Lift the mower, unscrew the central blade bolt with a wrench, remove the worn blade and install the new one respecting the rotation direction. Tighten to the recommended torque (about 50 Nm).

The mower vibrates abnormally, why?

Vibrations may come from an unbalanced or damaged blade, a worn belt or an object stuck in the deck. Check and replace parts if necessary.

Where to find spare parts for this model?

Spare parts are available at Güde dealers or online. Refer to the manual for part numbers. Blades, belts and filters are commonly available.

USER MANUAL Trike Big Wheeler 565D GUDE

GB Translation of the original instructions

Big Wheeler TRIKE 565D

95357

ENGLISH Please read the instructions carefully before starting the machine.

DE Montage SI Montaža

GB Assembly HR Montaža

FR Montage BG Монтаж

IT Montaggio RO Montaj

NL Montage BA Montaža

CZ Montáž

SK Montáž

HU Szerelés

1

6-10

DE Montage

GB Assembly

FR Montage

IT Montaggio

NL Montage

CZ Montáž

SK Montáž

HU Szerelés

SI Montaža

HR Montaža

BG Монтаж

RO Montaj

BA Montaža

6

2x

5

6

7

8

1	DE Montage	SI Montaža
	GB Assembly	HR Montaža
	FR Montage	BG Монтаж
	IT Montaggio	RO Montaj
	NL Montage	BA Montaža
	CZ Montáž
	SK Montáž
	HU Szerelés

DE Montage

GB Assembly

FR Montage

IT Montaggio

NL Montage

CZ Montáž

SK Montáž

HU Szerelés

SI Montaža

HR Montaža

BG Монтаж

RO Montaj

BA Montaža

13

1	DE Montage	SI Montaža
	GB Assembly	HR Montaža
	FR Montage	BG Монтаж
	IT Montaggio	RO Montaj
	NL Montage	BA Montaža
	CZ Montáž
	SK Montáž
	HU Szerelés

1

DE Ölstand kontrollieren

GB Oil level inspection

GB Check the oil level whenever the appliance is to be put into operation. Add engine oil if necessary. Check the oil level whenever the appliance is to be put into operation. Add engine oil if necessary.

2

2

DE Ölstand kontrollierenGB Oil level inspectionFR Contrôle du niveau d'huileIT Controllo livello d'olioNL Oliepeil controlerenCZ Kontrola stavu olejeSK Kontrola stavu olejaHU Olajszint ellenőrzése

SI Kontrola stanja oljaHR Kontrola razine uljaBG Контрол на състоянието на маслотоRO Verificarea stării uleiuluiBA Kontrola nivoa ulja

DE Ölstand kontrollieren

GB Oil level inspection

GB To ensure quality, every piece of equipment is subject to a test operation and filled with motor oil. Oil is drained before transport; however, there can be some motor oil remains on the dip stick. Please check carefully the oil level and add motor oil again.

2

DE Schnitthöhe einstellenGB Cutting height settingFR Réglage de la hauteur de coupeIT Impostazione dell'altezza di taglioNL Instelling van de maaihoogteCZ Nastavení výšky sečeníSK Nastavenie výšky koseniaHU Kaszálási magasság beállítása

SI Nastavitev višine košnjeHR Podešavanje visine sječenjaBG Pergyliране на височината на сеченERO Reglarea înăltimii de tăiereBA Podešavanje visine sječenja

DE Bugrad

GB nose wheel

FR roue avant

IT ruotino anteriore

NL neuswiel

CZ prídové kolo

SK predné koleso

HU orrfutó

SI nos kolesih

HR nos kotača

BG колело носа

RO roți nas

BA nos kotača

2

2

DE Mähen - MulchenGB mow - mulchingFR tondre - paillageIT falciare - pacciamaturaNL maaien - mulchingCZ sekat - mulčováníSK kosit - mulčovanieHU szénaboglya - talajtakarás

SI kosite - mulčenjeHR kositi - zagrtanje biljakaBG koся - наторяванeRO cosi - mulcireBA kositi - zagrtanje biljaka

DE Mähen - Sammeln

GB mow - collect

FR tondre - collecter

2

DE Mähen - AuswerfenGB mow - ejectFR tondre - éjecterIT falciare - espellereNL maaien - uitwerpenCZ sekat - vyhnatSK kosit' - vyhnat'HU szénaboglya - kiadása

SI kosite - izmetHR kositi - izbacitiBG koся - изхвърлямRO cosi - evacuaBA kositi - izbaciti

STOP

DE Mähanweisungen

GB Cutting instructions

FR Consignes de tonte

DE Mähanweisungen
GB Cutting instructions
FR Consignes de tonte
IT Istruzioni per taglio
NL Aanwijzingen voor het maaien
CZ Pokyny k sečení
SK Pokyny na kosenie
HU Utasítás kaszáláshoz

SI Napotki za košnjo
HR Upute za sječenje
BG Инструкции за сечене
RO Instructiuni pentru cosit
BA Upute za sječenje

DE Betrieb - START

GB Operation - START

5	DE Reinigung / Wartung	SI Čiščenje / Vzdrževanje
	GB Cleaning / Maintenance	HR Čiščenje / Održavanje
	FR Nettoyage / Entretien	BG Чистене / Поддръжка
	IT Pulizia / Manutenzione	RO Curățare / Întreținere
	NL Schoonmaken / Onderhoud	BA Čiščenje / Održavanje
	CZ Čištění / Údržba
	SK Čistenie / Údrzba
	HU Tisztítás / Karbantartás

GB Cleaning / Maintenance

FR Nettoyage / Entretien

DE Zündkerze

GB Spark plug

5

DE ÖlwechselGB Oil changeFR Remplacement d'huileIT Cambio dell'olioNL OlieverversingCZ Výměna olejeSK Výmena olejaHU Olajcsere

SI Menjava oljaHR Zamjena uljaBG Смяна на маслотоRO Înlocuirea uleiuluiBA Zamjena ulja

DE Luftfilter

GB Air filter

FR Filtre à air

IT Filtro d'aria

NL Luchtfilter

CZ Vzduchový filtr

SK Vzduchový filter

HU Levegőszűrő

SI Zračni filter

HR Zračni filtar

BG Въздушен филтър

RO Filtru de aer

BA Zračni filtar

GB Paper filter to be cleaned with compressed air only! Never use water!

Cutting width....550 mm

Collection bag capacity 65 l

Fuel SUPER/SUPER PLUS/SUPER E10/NORMAL/NORMAL E10

Weight....37,2 kg

Dimensions....1750 x 560 x 980 mm

Noise and Vibration Information

Sound pressure level Ln01) .....83,7 dB (A)

Sound power level L 98 dB (A)

Wear ear protectors!

Vibration emission value a_h²⁾ 6,9 m/s²

¹⁾ Uncertainty K=3 dB (A), ²⁾ Uncertainty K=1,5 m/s ²

Warning The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet. The vibration emission level may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. An accurate estimate of the vibratory load should also take into account the times when the tool is shut down or when it is running but not actually in use. This may significantly reduce the vibratory load over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

Read and understand the operating instructions before using the appliance. Familiarise with the

control elements and how to use the appliance properly. Abide by all the safety measures stated in the service manual. Act responsibly toward third parties. The operator is responsible for accidents or risks to third parties. In case of any doubts about connection and operation refer please to our customer center

delivered items

1 Mulching wedge

2 Side ejection

3 Collection bag

4 Spark plug wrench

5 Bowden clamps

6 Wheels/screens including star screw/U-washer

7 Screws

8 height adjustable nose wheel

9 Panel

10 Accessories

Specified Conditions Of Use

The mower has been designed for cutting grass and grass areas with a maximum climb of 20° in private gardens around the house and in garden colonies.

Do not use this product in any other way as stated for normal use. Not observing general regulations in force and instructions from this manual does not make the manufacturer liable for damages.

⚠️ Use the appliance only outside, never use it in confined and bad ventilated areas.

The mower must not be used for cutting bushes, hedges and thickets, for cutting and mulching creepers or lawns on roofs or in balcony boxes. The mower must also not be used as a crusher for mulching tree cuttings and hedges or levelling any terrain roughness.

Requirements for operating staff

The operating staff must carefully read the Operating Instructions before using the appliance..

This device is not intended for use by persons (inclu-

ding children) with limited physical, sensory or mental capabilities or without the necessary lack experience or knowledge unless they are supervised by a person who is responsible for their safety or were instructed by that person in how to use the device.

Qualification: Apart from the detailed instructions by a professional, no special qualification is necessary for appliance using.

Minimum age: Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education.

Local regulations may stipulate the minimum age of the user.

Training: Using the appliance only requires corresponding training by a professional or the Operating Instructions. No special training is necessary..

Emergency procedure

Danger of injury!

Never put your hands and feet near the rotating parts.

Danger of burns!

Some parts of the appliance get too hot when the appliance is operated. Do not touch any hot parts, e.g. engine and muffler.

Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. For the sake of eventual accident, in accordance with DIN 13164, a workplace has to be fitted with a first-aid kit. It is essential to replace any used material in the first-aid kit immediately after it has been used. If you seek help, state the following pieces of information:

1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)

Symbols

Caution!

Read the Operating Instructions

Wear ear protectors!
Wear eye protective goggles!

Caution - hot surface!
Risk of poisoning!

Warning against bounced subjects

Keep distance of persons
Observe to keep out of dangerous zone

Switch off the engine before any work on it.

Keep a sufficient distance from the cutting knife when operating the appliance.

Caution, risk of drawing-in!

Risk of explosion

Refuel the engine only when switched off.

Risk of poisoning!

Use the appliance only outside, never use it in confined and bad ventilated areas.

Prohibited smoking and open fire using.

Keep children and other persons including animals in a safe distance when using the appliance.

Use the appliance only outside, never use it in confined and bad ventilated areas.

Wear safety cut through resistant shoes with safety sole and steel toe!

Caution - hot surface!

Warning against dangerous voltage

Protect against humidity

This side up

Safety instructions

Warning

Read all safety warnings and all instructions, including those given in the accompanying brochure.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

Keep children and other persons including animals in a safe distance when using the appliance. Minimum safe distance is 5 m.

Wear personal protective equipment.

Wear solid shoes and long trousers.

Wear protective gloves if necessary.

Use the appliance in broad daylight or in a well-lit environment.

Check carefully the terrain where the appliance is being used and remove any items that could get caught and be thrown away.

⚠️ Fuel is highly flammable.

Keep the fuel in sui,le containers only.

The appliance may only be refuelled outdoors and not near open fire or burning cigarettes.

Refuel before starting the appliance. If the engine is running or still hot, it must not be refuelled or the tank cover opened.

Make sure the fuel does not overflow. If the fuel overflows, the engine must not be started. Remove any dirt from the appliance and prevent any attempt at ignition until fuel fumes have evaporated.

The engine must necessarily be filled with engine oil before being put into operation for the first time.

Check the oil level whenever the appliance is to be put into operation. Add engine oil if necessary.

Carry out a visual inspection before any use to make sure the appliance, especially the cutting tools, fastening parts and the entire cutting unit are not damaged.

⚠️ Check all screw and plug-in connections and protective equipment if firm and tightened properly and whether all moving parts are running smooth whenever the appliance is to be put into operation.

The protective equipment on the appliance is strictly prohibited to be disassembled, changed, used in conflict with the designation and it is prohibited to attach any protective equipment of other manufacturers.

The appliance must not be used if damaged or safety equipment is defective. Replace any worn-out and damaged parts..

Do not start the engine before your feet are in a safe distance from the cutting tools.

Do not incline the appliance when being started.

Do not start the appliance when you are standing in front of the ejection opening.

Make sure your posture is safe, especially on slopes. Do not cut on too steep slopes. Be particularly careful when changing travelling direction on slopes.

Pay maximum attention when turning around and pulling the appliance to you..

Switch the mower off whenever carrying or inclining it or when being outside a grass area. Wait until all rotating parts have stopped.

If an undesirable item is encountered or the appliance starts vibrating, the appliance must be switched off and the socket plug removed. Check whether the appliance is not damaged. Repair any damage.

Switch the appliance immediately off after finishing your work.

Do not store the appliance in enclosed places just after being switched off but let it cool down outdoors instead.

Never store the appliance with petrol in the tank inside a building where petrol fumes may potentially get in touch with open fire or sparks.

Replace any defective muffler.

Do not change the controlled engine setting and do not rev the engine up.

Maintenance

Switch the engine off and remove the socket plug before any work on the engine. Wait until all rotating parts have stopped the appliance has cooled down.

Keep the appliance, especially the tank and engine, clean at all times. Clean the ejection opening and cover at regular intervals.

Apply environment-friendly oil to all moving parts. Check the collection bag at regular intervals for any wear and aging.

Refer all servicing to qualified service personnel.

Use only original accessories and original spare parts.

Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries.

Guarantee

Warranty period of 12 months applies to commercial use and 24 months applies to private use and commences on the day of purchase of the device.

The guarantee solely covers inadequacies caused by material defect or manufacturing defect. Original payment voucher with the sales date needs to be submitted for any claim in the guarantee period.

The guarantee does not cover any unauthorised use such as appliance overloading, use of violence, damage as a result of any unauthorised interference or caused by foreign items. Failing to follow the operating and assembly instructions and common wear are also not included in the guarantee.

Service

Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions? We will quickly help you and without needles bureaucracy at our web pages at www.guede.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be found on the type label. Please enter it here for future reference:

Serial No.:

Art. No:

Year of production:

Inspection and maintenance plan

Regular servicing period Before		any start-up	After 1 month	After 3 months	After 6 months	After 12 months	After 24 months
			5 Hours of operation	25 Hours of operation	50 Hours of operation	100 Hours of operation	250 Hours of operation
Engine oil (10W-40)	Inspection	√
	Change		√		√
Air filter Inspection		√
					√
Spark plug	Inspection					√
	Clean

Provide appropriate servicing upon the earlier of the following: in the given month or after the specified hours of operation have expired.

Defects searching

Defect	Cause
The motor does not start	Start-Stop lever has not been pressed Press the Start-Stop lever
	Primary pump has not been used Use the primary pump
	Lack of fuel Add some fuel
	Bowden cables are too long Adjust the Bowden cables using the coupling nut.
	Wrong fuel, storing without petrol tank being drained	Drain the fuel tank and carburettor.Add fresh petrol.
	Sooted spark plug (carbon residues on electrodes), electrodes distance too big	Clean the spark plug, check the plug thermal value, possibly change the plug, set the electrodes distance to 0.6-0.7 mm
	The spark plug is wet from petrol (oversaturated engine).	Dry the spark plug out and refit it.
Grass is not collected	Blocked channelFull collection bagToo wet grass	Clean the ejection channelEmpty the collection bagCut in dry weather

Attention - surface chaude!

EC-DECLARATION OF CONFORMITY

We, hereby declare the conception and construction of the below mentioned appliances correspond - at the type of construction being launched - to appropriate basic safety and hygienic requirements of EC Directives. In case of any change to the appliance not discussed with us the Declaration expires.

DECLARATION CE DE CONFORMITE

PROHLASENI O SHODE EU

2006/95/EC 2004/108/EC

2009/105/EC 1907/2006/EC

2011/65/EC ROHS 2009/142/EC

89/686/EEC (PPE) 1935/2004/EC

□ □

2006/42/EC

Annex IV

Notified Body:

Type Ex. Cert.-No.:

2000/14/EC_2005/88/EC

Noise: guaranteed L_WA 98 dB (A)

97/6 8/EC_2004/26/EC

Emission No.: e1*97/68SN3-IA*2004/26SN3-IIA*0331*03