UPS-OLC10DP - Inverter Mach Power - Free user manual and instructions

Product Type	Uninterruptible Power Supply (UPS)
Brand	Mach Power
Model	UPS-OLC10DP
Power Capacity	1000 VA / 900 W
Input Voltage	220-240 VAC
Output Voltage	220-240 VAC (regulated)
Type	Line-Interactive
Waveform	Simulated sine wave
Battery Type	Sealed Lead-Acid (12V / 7Ah or 9Ah)
Runtime (half load)	Approx. 10-15 minutes
Recharge Time	4-6 hours to 90%
Number of Outlets	2-4 battery backup + 2-4 surge only
Dimensions (W x D x H)	Approx. 280 x 140 x 86 mm
Weight	Approx. 4.5 kg
Protection Features	Surge protection, overload, short circuit, low battery alarm
Noise Level	< 45 dBA
Operating Temperature	0°C to 40°C
Cooling Method	Fan cooling
Maintenance	Replace battery every 3-5 years; keep vents clean
Safety Compliance	CE, RoHS

Frequently Asked Questions - UPS-OLC10DP Mach Power

What does the UPS-OLC10DP protect against?

The Mach Power UPS-OLC10DP provides protection against power surges, sags, spikes, and complete blackouts, ensuring your equipment stays operational during short interruptions.

How long do the batteries last?

Batteries typically last 3-5 years depending on usage and ambient temperature. When runtime becomes too short, replace them with compatible sealed lead-acid batteries.

Can I connect a laser printer to the UPS?

It is not recommended to connect laser printers to the battery backup outlets due to high startup power draw. Use surge-only outlets if available.

How do I perform a self-test?

Press and hold the test button (if available) for 2-3 seconds. The UPS will switch to battery mode briefly to verify functionality. Refer to manual for precise steps.

What do the LED indicators mean?

Typical LEDs: Green = mains power normal, Yellow/Amber = battery mode or low battery, Red = fault or overload. Consult manual for exact pattern.

Can I replace the battery myself?

Yes, the battery compartment is user-accessible. Turn off and unplug the UPS, remove the cover, disconnect the old battery, and install a new one of the same type and rating.

Why does the UPS beep continuously?

Continuous beeping indicates battery mode (on battery) or low battery. If on mains power, it could signal a fault. Check for overload or replace battery.

What is the typical runtime at half load?

At 50% load (about 450W), runtime is approximately 10-15 minutes. Actual runtime depends on battery health and age.

How do I clean and store the UPS?

Wipe the exterior with a dry cloth. Do not use liquids. Store in a cool, dry place (0-40°C). For long storage, charge battery every 3-6 months.

Is the UPS-OLC10DP compatible with generators?

Yes, but the generator output must be stable and within voltage/frequency range (50/60 Hz). Some generators may cause frequent switching; use a verified model.

USER MANUAL UPS-OLC10DP Mach Power

Black battery pack with a digital temperature monitor and power supply unit (no visible text or symbols on the device body)

DATASHEET

UPS ONLINE SINGLE PHASE IN/OUT

1KVA / 900W

MODEL: UPS-OLC10DP

FEATURES

Rack Tower design	Output bypass settable for 1/2/4KVA via LCD
High frequency and true double-conversion	50Hz / 60Hz frequency converter mode available on 6-10KVA
DSP digital control technology	Selectable battery low voltage via LCD
Input power factor correction (PFC)	Automatically diagnose when starts
Wide input voltage range (110V-300V)	Advanced battery management (ABM)
Output power factor 0.9	Short circuit and overload protection
Cold start	Automatically charging battery at UPS off mode
Frequency adaptive	Fan speed auto control when load varies
ECO mode operation for energy saving	Standard RS232 communication port and RJ45 protection
Selected output voltage via LCD

Line drawing of a tall industrial tower with ventilation grilles and control panel (no text or symbols)

CONVERTIBLE

RACK / TOWER DESIGN

SPECIFICATION

MODEL - CAPACITY	UPS-0LC10DP - 1KVA / 900W
INPUT
Rated Voltage	208V / 220V / 230V / 240VAC
Voltage Range	Half load (115-295) ± 5VAC, Full load (145-95) ± 5VAC
Frequency	45-55Hz ± 0.5%Hz or 55-65Hz ± 0.5%Hz (Auto Sensing)
Power Factor	≥0.98
Bypass Voltage Range	Rated output voltage -34V - Rated output voltage +32V
OUTPUT
Voltage	208V / 220V / 230V / 240VAC Setting available via LCD
Voltage regulation	± 1%
Frequency	Synchronized with utility on AC mode; 50/60 ± 0.2Hz on battery mode
Waveform	Pure sine wave
Crest factor	3:1
Harmonic distortion	≤3% (linear load); ≤5% (Non-linear load)
Tranfer time	AC mode to battery mode: 0ms / Inverter model to bypass mode 4ms(Typical)
Overload capability	105%-150%: Transfer to bypass after 30s / >150: Transfer to bypass after 300ms
BATTERY
DC Voltage	24V
Inbuilt battery	2 x 9Ah
Charge current	1A
Typical recharge time	8 Hours recover to 90% capacity
ALARM
Utility failure	Beep / 4sec
Battery low	Beep / 1sec
Overload	Beep twice / 1sec
UPS fault	Long Beep
EFFICIENCY
AC Mode	≥90%
Battery mode	≥87%
ECO mode	≥98%

ENVIRONMENT

Humidity	20~90% RH @ 0~40°C (non-condensing)
Noise Level	≤50dB (1m)

MANAGEMENT

USB Port	Supports Windows 98 / 2000 / 2003 / XP / Vista / 2008 / 7 / 8
Optional SNMP/AS400	Power management from SNMP manager and web browser

PHYSICAL

Dimension (L x W x H)	440 x 468 x 88mm
Net weight	14.3 kg
Gross weight	17.7 kg