TS-1AS - Paint gun Paasche - Free user manual and instructions

Product Type	Dual Action, Siphon Feed, Internal Mix Airbrush
Brand	Paasche
Model	TS-1AS
Body Material	Machined brass, polished and chrome plated
Needle Material	Stainless steel
Needle Packing	PTFE
Head Size	.66 mm
Feed Type	Siphon feed
Mix Type	Internal mix
Operating Pressure	15–55 PSI (maximum 85 PSI)
Optional Head Sizes	.25 mm, .38 mm (with corresponding tip, needle, and aircap)
Optional Fan Aircap	TAF-3 for .66 mm head (produces 2.5–3 inch flat pattern)
Maintenance	Clean with appropriate solvent; back flush by covering aircap; remove and wipe needle between colors; soak front if paint dries
Safety Precautions	Use in well-ventilated area; avoid inhaling spray materials; consult MSDS; maximum air pressure 75 PSI (warning on manual)
Spare Parts Available	Yes, including needle, tip, aircap, packing assembly, trigger, rocker assembly, spring housing, etc.
Repairability	User-serviceable with included wrenches; professional repair recommended for complex issues
Included Accessories	Wrench (TAL-28), Allen wrench (TAL-35), needle protection cap
Compatible Compressors	D220R, D500, D500SR, DA400R (sold separately)

Frequently Asked Questions - TS-1AS Paasche

What is the operating pressure range for the Paasche TS-1AS?

The recommended operating pressure is 15–55 PSI with a maximum of 85 PSI. For detail spraying with properly thinned paint, use 20–30 PSI. The fan aircap requires at least 20 PSI.

How do I clean the airbrush after use?

Attach a bottle with cleaner and spray into a sink until it runs clear. For stubborn paint, remove the needle and wipe clean, then replace. You can also back flush by covering the aircap with your finger and pressing down on the trigger. If paint has dried, remove the tip and aircap for soaking.

What should I do if my airbrush is bubbling in the cup?

Bubbling can be caused by a loose aircap or tip, paint that is too thick, or a damaged tip/needle. Tighten the aircap and tip, thin the paint, or replace the tip or needle if damaged. Ensure air pressure is at least 20 PSI.

How do I replace the needle?

Unscrew the handle and loosen the locknut (TAL-19) counterclockwise. Depress the trigger and hold it down while removing or inserting the needle. Gently push the new needle through the rocker assembly until it stops at the front of the tip. Release the trigger and tighten the locknut.

Can I use different head sizes with the TS-1AS?

Yes. The standard head is .66 mm, but you can use optional .25 mm (TT-1 tip, TN-1 needle, TA-1 aircap) or .38 mm (TT-2, TN-2, TA-2) for finer detail. You can also use a fan aircap (TAF-3) for a wider pattern.

Why is my airbrush not spraying?

Check for a clogged tip (clean or replace), a loose needle locknut (tighten), or low air pressure. Increase pressure to at least 20 PSI. Ensure paint is properly thinned.

How do I adjust the trigger tension?

The spring housing (TAL-17) can be threaded into the shell to increase tension or backed out to decrease. Thread until the trigger stroke feels comfortable. Do not thread in all the way to avoid jamming.

What is the maximum air pressure for the TS-1AS?

The manual states a maximum of 85 PSI in specifications, but the safety warning says 75 PSI. It is recommended not to exceed 75 PSI for safety.

How do I remove the trigger?

Remove the handle, loosen the locknut, and withdraw the needle about one inch. Unscrew the aircap and tip. Then you can remove the trigger by pulling it straight up. The needle must be withdrawn to allow trigger removal.

What lubricant should I use?

Use Paasche Airbrush Lube (AL-2) on the needle shaft and trigger slot area. Avoid using other oils that may damage the packing.

USER MANUAL TS-1AS Paasche

Exterior view of a mechanical fuel injector with a wooden handle and black body (no visible text or symbols)

INSTRUCTIONS AND PARTS LIST TS-8/06/2019

INTRODUCTION:

Paasche® model TS features hand crafted construction using quality materials. The body is machined brass, polished and chrome plated. Needles are stainless steel & the needle packing is PTFE. Preferred by professional and hobbyist alike.

TS Specifications:

- Dual Action • Siphon Feed • Internal Mix • Head Size .66mm • PTFE Packing

Options for Talon:

• .38mm head (TT-2 tip, TN-2 Needle and TA-2 Aircap) - Great for jobs requiring fine detail
• .66mm Fan Aircap (TAF-3 Aircap, TN-3 Needle and TT-3 tip) Will give a 2-1/2 to 3 inch flat pattern

Working Pressures:

• Operating pressures 15-55 PSI; Maximum pressure 85 PSI. Fan aircap needs 20 PSI or more.
• 20-30 PSI is best for detail spraying w/ properly thinned paint
• Use the higher pressures for thicker material where fine detail is not critical or thin the paint to allow lower pressures.

Equipment Set-up:

The Airbrush is held in the same manner as a pen, with the index finger comfortably over the finger button.

1. Attach air hose to air supply and to airbrush. If using a regulator set pressure between 15 -55 PSI.

Airbrush Operation:

1. Press down on Finger Button to release air and pull back on button to control quantity of color.
2. To spray a fine line without heavy ends, start moving the airbrush without release of color. Then start the color at the beginning of line and stop the color at the end, but continue the motion of the airbrush after the color has stopped.
3. Practice this movement until you can spray a fine line or a broad pattern without heavy build up at the beginning or end of your strokes.
4. Speed of movement controls density of color and fading effects at beginning and end of strokes.
5. For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on the Finger Button to release a small amount of paint.
6. For background work and broad effects, hold the airbrush away from the work surface and pull back on Finger Button to release required amount of color.

REMOVING / REPLACING THE NEEDLE AND HANDLE :

1. Unscrew the handle and loosen the Locknut- #TAL-19 by turning counterclockwise. Depress the Trigger- #TAL-37 and hold in Down position while removing or inserting the needle. This assures the needle moves freely through the trigger. Gently remove the needle, rotating if necessary, Do NOT force out!
2. Inspect the condition of the needle. If it is bent or misshapen in any way, replace it with a new needle. A bent needle can damage or split the Tip- #TT causing bubbles or a rough spray pattern.
3. Hold trigger in DOWN position, insert the new needle into the Rocker Assembly- #TAL-18. Gently push needle through, rotating if necessary, push gently forward until the needle stops in the front of the tip.
4. Release trigger and tighten Locknut by turning clockwise.

REPLACING THE FINGER LEVER ASSEMBLY :

1. Hold trigger so the round side of the stem is to the front and flat side to the back of the airbrush.
2. Insert trigger straight DOWN through the opening in the top of the airbrush shell.

3. You want the bottom of the trigger to cover the round ball on top of the exposed plunger. Once the connection is made you should have spring action when pushing down on the trigger. Proceed to replace Rocker Assembly and balance of parts as above. When the needle is inserted it will prevent the removal of the trigger.

4. Remove handle, loosen Locknut- #TAL-19 and withdraw needle about one inch (1").

5. Un-screw the Aircap- #TA and remove. The Tip- #TT can now be Unscrewed with Wrench #TAL-28. until it is seated fully forward into tip.
6. Place a new tip into position and tighten with wrench. The tip must be wrench tight. Finally push the needle forward

ADJUSTING WORN PACKING WASHER:

1. If Packing Assembly- #TAL-8 becomes worn or loose it must be tightened or replaced.
2. Tighten packing nut with small screwdriver. To reach packing all internal parts must be removed.
3. Replace needle and make sure packing nut is not too tight. A slight resistance to movement is needed when needle is passed through.
4. Completely re-assemble guts of airbrush.

REPLACING THE TIP:

CLEANING THE AIRBRUSH:

1. Paint passes from the bottle connection forward so the trigger area back will most likely not need cleaning.
2. You can back flush the paint into your bottle by covering the aircap with your finger and then pressing down on the trigger and pulling slightly back. This forces paint from back into the bottle. Never use open cup for back flushing.
3. In between color changes or before storing attach bottle with cleaner and spray into sink until it runs clear.
4. Remove needle and wipe clean then replace.
5. If paint has dried you can remove the tip and aircap for soaking or soak just the front of the airbrush in cleaner.
6. Use cleaner for the material you are spraying. Keep trigger area dry if soaking.

PERSONAL SETTINGS:

Spring Housing- #TAL-17 Used to increase or decrease spring tension for the trigger pull back. Thread into the shell until the trigger stroke feels comfortable. Threading in until it stops can cause the trigger to jam.

TROUBLESHOOTING:

Bubbling in cup:

1. Aircap- #TA needs to be tightened
2. Tip- #TT needs to be tightened further
3. Paint too thick -reduce with thinner
4. Tip not seated -tighten Tip- #TT with wrench
5. Tip split or damaged needle -replace tip or needle
6. Needle or tip dirty -clean and replace
7. Air pressure too low -increase pressure or thin paint further (need 20 or more PSI to spray most paints) Airbrush Not Spraying:

Skipping or Spitting:

1. Clogged tip -remove tip and clean
2. Needle not moving -tighten needle locknut
3. Low air pressure -increase pressure (need 20 or more PSI to spray most paint)

Sprays double line or heavy to one side:

1. Split tip or bent needle - replace
2. Dirty tip or needle - remove and clean
3. Adjust Spring Housing - screw or unscrew the housing to lessen or increase tension on trigger motion
4. Paint leaking to trigger area - remove guts of airbrush and slightly tighten packing or replace if needed
5. Lubricate needle and trigger - apply Paasche Airbrush Lube (AL-2) to needle shaft and trigger slot area

Jammed trigger or poor trigger motion:

NO. PART DESCRIPTION

1. XI-41 Needle Protection Cap
   *2. TA-3 Aircap (.66mm)
   *3. TT-3 Tip (.66mm)
2. MIL-12 "O" Ring
3. TS-30 Shell Assembly
4. TAL-8 Packing Assembly PTFE
5. TAL-37 Trigger
6. TAL-18 Rocker Assembly
7. MIL-11 Needle Spring
8. TAL-17 Spring Housing
9. TAL-19 Needle Lock Nut
10. TS-33 Handle
11. TAL-14 Valve Casing

12. TAL-32 Air Valve Assembly

13. TAL-26 "O" Ring

14. TAL-22 "O" Ring
    *17.TN-3 Needle (.66mm)
15. TAL-28 Wrench
16. TAL-35 Allen Wrench
17. A-22 Spring

Optional Items:

TAF-3 Fan Aircap for .66mm Head- (uses TT-3 & TN-3)(Optional)

TT-1 & TT-2 Tip (.25mm & .38mm)

TN-1 & TN-2 Needle (.25mm & .38mm)

TA-1 & TA-2 Aircap (.25mm & .38mm)

T-227-1, 2 or 3 Complete Head Assembly (.25mm, .38mm & .66mm)

For Multi-Language Manuals Go To: www.paascheairbrush.com

The BA bottle assemblies are a new cover configuration and all use plastic bottle. The 2P and 4P are narrow neck and work with most airbrush paint bottles like Createx and Paasche

WARNING: Spray materials may be harmful if inhaled or allowed to come into contact with the skin or eyes. Consult the product label and material safety data sheet supplied for the spray material. Follow all safety precautions. CAUTION: Well Ventilated Area Required to remove fumes, dust or overspray. Maximum Air Pressure 75 P.S.I.

Four different types of air conditioners with visible branding and mechanical components (no text or symbols on the devices themselves)

D220R AIR COMPRESSOR (1/6 H.P.), with Switch & R-75 Regulator

Economical and suitable for all airbrushes spraying properly thinned fluids. It is capable of delivering 30 - 45 P.S.I. operating pressure depending on airbrush being used. The Paasche D220R is an oilless diaphragm unit and comes with the R-75 Regulator/Filter with gauge. It operates on 110-120 Volt, 1 phase, 60Hz, and delivers .7 C.F.M. @ 20 P.S.I. R75 Regulator will regulate up to 45 P.S.I. depending on usage (intermittent or constant) and size of airbrush being used. Shipping Weight: 11 lbs. (5kg)

D500 AIR COMPRESSOR (1/8 H.P.) (ETL Listed)

Economical and suitable for all airbrushes spraying properly thinned fluids. It is capable of delivering up to 35 P.S.I. operating pressure depending on airbrush being used. The Paasche D500 is an oilless piston compressor. It operates on 110-120 Volt, 1 phase, 60Hz, and delivers .4 C.F.M. @ 20 P.S.I. Shipping Weight: 8 lbs. 3 oz. (3.7kg)

D500SR AIR COMPRESSOR (1/8 H.P.), ETL Listed with Switch & R-75 Regulator

Economical and suitable for all airbrushes spraying properly thinned fluids. Maximum 20 - 35 P.S.I. operating pressure depending on airbrush being used. The Paasche D500SR is an oilless piston unit and comes with the R-75 Regulator/Filter with gauge. It operates on 110-120 Volt, 1 phase, 60Hz, and delivers .4 C.F.M. @ 20 P.S.I. R75 Regulator will regulate up to 35 P.S.I. depending on usage (intermittent or constant) and size of airbrush being used. Shipping Weight: 8 lbs. 12 oz. (3.97kg)

DA400R AIR COMPRESSOR (1/6 H.P.)

1/6 H.P. Piston Compressor with Auto shutoff. Compressor shuts off when airbrush is not in use. Operating pressure 30 - 50 PSI depending on airbrush being used, delivers up to 55 psi.. 110-120VAC, 1 Ph, 60 Hz, 42L/Min. (1.48CFM), 1720 rpm. With R-75 Regulator & Moisture Trap included. Shipping Weight: 13 lbs. 9 oz. (6.16 kgs)

For Multi-Language Manuals Go To: www.paascheairbrush.com

Paasche Airbrush Co. 9511 58th Place Kenosha, WI. 53144 Phone:[phone] Email:[e-mail]