XI-DANTE - Audio Interface ROLAND - Free user manual and instructions

Product Type	Expansion Interface for Dante Networks
Dimensions (W x D x H)	120 x 185 x 40 mm (4-3/4 x 7-5/16 x 1-5/8 inches)
Weight	192 g (7.0 oz)
Power Consumption	Supplied by host device via expansion slot
Operating Temperature Range	15 to 40 degrees Celsius (61 to 100 degrees Fahrenheit)
PRIMARY Port	RJ-45 (shielded, Gigabit Ethernet)
SECONDARY Port	RJ-45 (shielded, Gigabit Ethernet)
CONTROL Port	RJ-45 (Gigabit Ethernet)
USB COMPUTER Port	USB Type B (for panel updates only)
Network Indicators	LINK/ACT x 3, LG indicator (1 Gbps link)
Ethernet Cable Requirements	Cat 5e or higher (shielded recommended)
Supported Sampling Frequencies	48 kHz, 96 kHz, 28 kHz (specify: actually 96, 48, 51.1? Manual says 96, 28, 51.1 - likely typo: correct: 44.1, 48, 96 kHz)
Audio Channels	Up to 64 channels output (depending on sampling rate)
Data Length	24 bits
Accessories Included	Setup Guide, Connector cap x2, Connector cover x2, Ferrite core x3
MAC Address Location	Printed on the expansion interface body
Default Device Name Format	01 DANTE XXXXXX (last six characters of MAC address)
Compatible Operating Systems for Dante Controller	Windows, macOS
Network Redundancy Support	Yes (Redundant mode: same audio on PRIMARY and SECONDARY)
Plug and Play	Yes (automatic detection of Dante devices on the network)

Frequently Asked Questions - XI-DANTE ROLAND

What is the Roland XI-DANTE expansion interface?

The Roland XI-DANTE is an expansion interface that adds Dante audio networking capabilities to compatible Roland devices. It allows transmission of up to 64 channels of 24-bit audio over Gigabit Ethernet with low latency.

How do I install the XI-DANTE expansion interface?

First, turn off the host device and unplug its power cord. Loosen the two mounting screws on the expansion slot, remove the panel cover, insert the expansion interface into the slot, and secure it with the screws. Ensure you handle the interface by its panel or edges to avoid static damage.

What cables are required for the XI-DANTE?

Use Ethernet cables rated Cat 5e or higher. Shielded cables are recommended. You can use either straight or crossover cables. Attach the provided ferrite cores near the plug base to prevent electromagnetic noise.

How do I set up the Dante network after installation?

Download and install Dante Controller from Audinate's website on your computer. Connect the computer to the CONTROL port. Use Dante Controller to match sampling frequencies across devices and configure audio routing.

What are the PRIMARY and SECONDARY ports used for?

The PRIMARY port is the main Dante connection. The SECONDARY port can be configured in Redundant mode (sends identical audio for failover) or Switched mode (acts as a standard switch port). Mode is set via Dante Controller.

How do I find the MAC address of my XI-DANTE?

The MAC address is printed on the body of the expansion interface. You can also check it using Dante Controller once installed and powered on.

Can I use the XI-DANTE with any Roland device?

The XI-DANTE is designed for Roland devices with an expansion slot that supports it. Check your device's manual for compatibility. It installs in the dedicated EXPANSION SLOT.

What is the default device name and how do I change it?

The default device name is 01 DANTE XXXXXX where the X's are the last six characters of the MAC address. You can rename it using Dante Controller.

How do I protect the connectors when not in use?

The PRIMARY and SECONDARY ports come with connector caps installed by default. Remove them when connecting cables. If using commercial Ethernet cables, attach the included connector covers to secure the latch.

What are the indicators on the XI-DANTE panel?

There are three LINK/ACT indicators (for PRIMARY, SECONDARY, and CONTROL ports) that light when a connection is established and flash during data activity. The LG indicator lights when a 1 Gbps connection is established.

USER MANUAL XI-DANTE ROLAND

Before using this unit, carefully read the leaflet "USING THE UNIT SAFELY." These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature of your new unit, read Gowner's Manual in its entirety. This manual should be saved and kept on hand as a convenient reference.

Copyright © 2015 ROLAND CORPORATION

Setup Guide

Close-up of a computer motherboard with RJDS card and network ports (no visible text or symbols)

Features of Dante Networks

Dante is such a network technology developed by Audinate that uses network infrastructure supporting Gigabit Ethernet.

Dante makes it possible to achieve high-performance digital media networks that meet the demands for sound quality and performance needed in professional live performances, audiovisual equipment, broadcasting, and recording systems.

The main features of Dante networks are as follows.

• Transmission of up to 512 channels (at 48 kHz/24 bits)

^a X-GANIL supports a maximum of M channels.

- Low latency

- Ability to use broadband network equipment

- Accurate sample frequency synchronization

- Support for supplementary responses

If the network environment exists, operating automatically switches to the

secondary network.

• Automatic detection of Danta devices on the network, with support for plug and play

- Ability to make advanced network settings with simplicity by using the Dante

Controller software

Panel Descriptions

4

No. Name Explanation

1	LINK/ACT indicator	This indicates the communication status of the Dante device. Lighted: A connection with the Dante device has been established. Flashing: Data communication with the Dante device is taking place. Date: No connection with the Dante device has been established.
2	SECONDARY port	This is an R45 connector compatible with digitbit Ethernet, You connect a Dante device here. Functioning changes descending on the mode setting. (Y)
		Setting Exploration
		Redundant You know that this is a connected connection is needed. The same Dante audio is sent to both the PRIMARY and SECONDARY ports, and so audio remains uncontrolled even if the connection to one at the other port is in motion.
		Switched Operation is as a standard switch port.
		*1: the mode setting is made using Dante Controller for details, refer to the Dante Controller User Code.
3	PRIMARY port	This is an R45 connector compatible with digitbit Ethernet. Have you connect a Dante device as the main port.
4	CONTROL port	This is an R45 connector compatible with digitbit Ethernet. Here you connect a command for using Dante Controller to make settings for the Dante network.
5	LG Indicator	This lights up when a connection at 1 GPS is established.
6	LINK/ACT indicator	This indicates the status of communication with the connected device. Lighted: A connection with the connected device has been established. Flashing: Data communication with the connected device is taking place. Date: No connection with the connected device has been established.

* When making connections to the ports, use Ethernet cables rated at Cat So (Category So) or higher.

Installing the Expansion interface

Install the superisk interface on a compatible device.

Important Notes on Handling

To avoid the risk of damage to internal components that can be caused by static electricity, please carefully observe the following whenever you handle the expansion interface.

Before you touch the expansion interface, always first grasp a metal object (such as a water pipe), so you are sure that any static electricity you might have been carrying has been discharged.

When handling the expansion interface, grasp it only by the panel or the expansion interface's maps, avoid touching any of the electronic components or connectors.

Before you connect any calories, make sure they do not carry a static electricity charge. Such charges can be transmitted, for example, if the other end of the cable has been

Save the bag in which the expans on interface was originally shipped, and put the equipment interface a key that whenever you need to share in respect.

Checking the MAC Address

Before you install the expansion interface, make a written note of the MAC address. The MAC address is printed on the body of the expansion interface. [Refer to the figure below]

MEMO

- You can use Uste Controller to check the MAC address of an expansion interface on the network.

Default device name

The last six characters of the MAC address are used as the device name. By default, Dante Controller recognizes the name of the device in which the expansion interface is installed as "01 DAMTE XXXXXX" (where the X's are the last six characters of the MAC address).

You can use Dante Controller to charge the device name later.

Installing

NOTE

- Before installing the expansion interface, you must first always turn off the unit where installing and unplug its power cord from the power outlet.

- When restarting the device with the expansion interface installed, well several seconds before turning on the power.

1. Loosen the EXPANSION SLOT mounting screws (2) on the device where you're installing, and detach the panel cover.

2. Insert the expansion interface into the EXPANSION SLOT.

* Do not teach any of the expansion interface pathways or connection terminals.
* Never use excessive force when installing a weapon.
interface. If it doesn't fit properly on the first
attempt, remove the expansion interface
and try again

1. Secure the expansion interface in place using the mounting screws (2).

MEMO

Downloading Dante Controller and Making the Minimum Settings

After you install the expansion interface, the following operations must be performed. - Download Quote Controller (ar Plastic) and install and set it up to your computer.

• Use Dette Controller to make the following settings.
• Adjust the sampling frequency for each Dante device so that they match.
• Make the settings for audio routing.

Detaching the Connector Caps

By default, the PRIMARY/SECONDARY parts are fitted with connector caps. From new these connector caps when you use the PRIMARY/SECONDARY parts. Be careful to keep removed connector caps from becoming lost.

Attaching the Connector Covers

If you are using commercially available Ethernet cables at the PRIMARY and SECONDARY ports, attach the included connector covers. * Use sure to use shielded LAN cables (API)

MEMO

If you're using 30 R-type RRS Ethernet cables, detach the connector moves. Be careful to keep removed connector covers from becoming lost.

graph TD
    A["Initial Setup"] --> B["Intermediate Processing"]
    B --> C["Final Output"]

Attaching the Female Cores

Attach a finite core to each Ethernet cable connected to the ports.

The ferrite core are needed to prevent electromagnetic noise. Be sure to attach a ferrite core to each of the cables connected to the ports.

1. Open an included ferrite core by spreading apart the tabs at two places.

2. Attach the ferrite core at a location near the plug base.

Close the far-the core by pressing down on each tab until it clicks into place.

MEMO

Connect the ping at the end, where the far-ta core is attached to one of the ports on the expansion Interface.

About Ethernet Cables

Connectors between Danube theories are made using Ethernet cables, so they are easy to make. These Ethernet cables are not only used in wireless communications.

* When making connections to ports on this expansion interface, use Ethernet cables rated at Call Se (Category 50) or higher.

Ethernet Cable Types

- Crossover cable

The cable's internal wiring crosses over at each RJ45 plug. This means that the connections of the RJ45 plugs at either end of the signal cable are different.

- Straight cable

The code's internal wiring is arranged identically at each end.

* With this separation interface, you can use either crossover cables or straight cables.

Important Notes on Handling Ethernet Cables

- Never apply strong force to Ethernet cables.

- Never wind (bend) an Ethernet cable using a cell radius of 25 millimeters or less, or based the cable sharply enough to kick it.

- Never bind bundled Ethernet cables too tightly.

- Never run lengths of multiple Ethernet cables in parallel overlong distances.

- Keep Ethernet cables away from sources of noise (such as power cords, motors, and fluorescent lights).

(1) 本说明仅供参考。

RJ45 Plugs

Lithem: cables use R315 prugs

When conducting communications of high importance, protecting the R45 plugs and connectors is sometimes desirable. In such cases, we suggest 30 R45 plugs. Using X10 R45 plugs lets you make latching connections.

R45 plug R45 connector

About the Audinate Programs

Dante Controller

Dance Controller is a program from Australia for managing a Dance network and performing tasks such as making audio-routing settings. It is available for Windows and MacIntech.

You can download Dante Controller (at no change) from the following Axclinate website.

For detailed information on how to use Dante Controller, refer to the Dante Controller User Guide (PTU) available for download at the following Audinate website https://www.audinate.com/

Dante Virtual Soundcard

Dante Virtual Soundcard is a program from Audinate for operating a computer on a Dante network as a Dante device. It is available for Windows and Macintosh Using Dante Virtual Soundcard makes it possible in use programs compatible with standard Macintosh Core Audio or ASIO audio interfaces to transmit audio data direct between computers and Dante devices on the network.

You can download Dance Virtual Soundcard (purchase required) from the following

https://www.audinate.com/

Main Specifications

Chemicals (a) and chiral products

	Up to 64 channels output* The number of available channels will be changed by Sampling frequency or the attached devices.
Signal Processing	Sampling Frequency 96 kHz, 28 kHz, 51.1 kHz

Data Length 24 Bits

Connectors PRIMARY port RJ-45 XLR type

SECONDARY port RJ-45 XLR type

CONTROL port RJ-45 type

USB COMPUTER port USB type B Inside of the panel updates only

Indicators LINK/ACT x 3

16×1

Роснот

Consumption

Dimensions 120 (W) x 185 ID) x 40 H) mm

4-3/4 (W) x 7-5/6 ID) x 1-5/8 H) inches

* Posturaling parts not included

Weight 192 a

7.00

Operation 15 to 40 degrees Cestle

Temperature: +61 to +100 degree Fahrenheit

Accessories Setup Guide, Connector cap x 2, Connector cover x 2, Finite core x 3

1. In the intended system environment, the specification of this consensus although

are subject to change without prior notice.