BDC8L-LA - Refrigerator DEWALT - Free user manual and instructions

Product Type	Travel Cooler and Warmer
Capacity	8 Liters
Power Consumption	48W at 12V DC
Voltage	12V DC
Cooling Temperature	Up to 18°C (65°F) below ambient
Warming Temperature	Up to 65°C (149°F)
Cooling Technology	Peltier (CFC-free)
Connection Cable	2m with 12V cigarette lighter adapter
Fuse Rating	10A glass fuse (replaceable)
Weight	3.19 kg
Controls	Sliding switch: Cool/Off/Heat; LED indicators (green cool, red heat)
Safety Features	Overheat protection; do not cover ventilation slots; do not switch directly between hot and cold
Cleaning	Wipe with damp cloth; mild soap if needed; do not immerse
Accessories Included	Shoulder belt, plastic lid, 12V power cord with adapter
Recommended Use	12V vehicle socket (car, boat, RV); camping

Frequently Asked Questions - BDC8L-LA DEWALT

Can I switch directly between cooling and heating?

No, you must turn the unit off and wait 10 minutes before switching between modes. Instant temperature change can damage the unit.

How long does it take to cool down?

Approximately 30-60 minutes to reach 7°C (45°F) below ambient temperature at 25°C room temperature. Pre-cooled items speed up the process.

What is the maximum warming temperature?

The warmer function heats to 65°C (149°F) and will cycle on and off to maintain that temperature.

Can I use this cooler with a household outlet?

No, this unit is designed for 12V DC only, typically from a vehicle cigarette lighter. Do not connect to 120V or 240V AC without a proper inverter.

Why is the LED not glowing when I turn it on?

Check that the vehicle ignition is on (accessory position), the adapter is firmly inserted, and the fuse in the cigarette lighter adapter (10A) is not blown. Also check the vehicle’s cigarette lighter fuse.

Can I store medicine or medical supplies in this cooler?

No, the manual advises against using the cooler for medical reasons or storing medicine. It is not designed to maintain precise temperatures required for medical items.

How do I clean the cooler?

Unplug and allow to reach room temperature. Wipe inside and outside with a damp cloth and mild soap if needed. Do not use abrasive cleaners or immerse in water.

What is the capacity of this unit?

The BDC8L-LA has an 8-liter capacity, suitable for small food and beverage items.

Can I use the cooler while the vehicle is turned off?

The vehicle must have the ignition on or be running to supply power. Using it with the engine off may drain the battery.

What should I do if the unit is not heating but the LED is on?

The internal heating element may be defective. Contact an authorized service center for repair. Do not attempt to fix it yourself.

USER MANUAL BDC8L-LA DEWALT

Travel Cooler and Warmer

MANUAL DE INSTRUCCIONES MANUAL DE INSTRUÇÕES INSTRUCTION MANUAL

Cat. N° BDC8L-LA

Line drawing of a portable electric heater with ventilation grilles and control panel (no text or symbols)

Español 3

Português 7

English 11

FIG. A

The cooler is suitable for cooling and warming foodstuffs. There is a switch to change between heating and cooling modes. The device has been designed for use with a 12V DC on-board power supply socket of a car (cigarette lighter), boat or RV. The appliance may also be used for camping use. The appliance shall not be exposed to rain.

GENERAL SAFETY RULES

⚠ Warning! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS General thermoelectric cooler safety warnings.

Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury.

Please read this operating manual carefully before starting the device. Keep it in a safe place for future reference. If the device is resold, this operating manual must be handed over to the purchaser along with it.

1. Do not operate the device if it is visibly damaged.
2. Ensure that the ventilation slots are not covered.

3. This device may only be repaired by qualified personnel. Inadequate repairs can lead to considerable hazards.

4. Persons (including children) whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely should not use this appliance without initial supervision or instruction by a responsible person.

5. Electronic devices are not toys. Always keep and use the device out of the reach of children.

6. Children must be supervised to ensure that they do not play with the device.

7. Food may only be stored in its original packaging or in suitable containers.

8. The cooling device is not suitable for transporting caustic materials or materials containing solvents.

9. Only connect the device with the 12V cable supplied to a 12V socket.

10. Do not pull the plug out of the cigarette lighter or the socket by the cable.

11. If the connection cable is damaged, it must be replaced with the cable of the same type and specifications.

12. Pull out the connection cable:

a. Before cleaning and maintenance
b. After use

1. Check that the voltage specification on the type plate corresponds to that of the energy supply.

1. Before starting the device, ensure that the power supply cable and the plug are dry.
2. Do not place the device near naked flames or other heat sources (heaters, direct sunlight, gas ovens etc.)

Caution! Danger of overheating: Ensure at all times that there is sufficient ventilation so that the heat that arises during operation does not build up. Make sure that the device is sufficiently far away from walls and other objects so that the air can circulate.

1. Do not fill the inner container with ice or liquid directly. It suggests to put ice or liquid in a container, and then put in the inner container.
2. Never immerse the device in water.
3. Protect the device and the cable against heat and moisture.
4. The manufacturer cannot be held liable for damage resulting from improper usage or incorrect operation.

Caution! If you wish to cool medicines, please check if the cooling capacity of the device is suitable for the medicine in question.

GENERAL SAFETY RULES

⚠ Warning! Do not switch from cold to hot or from hot to cold. The instant 100 degree change can damage the unit. You need to turn off the unit, wait 10 minutes and then slide the main switch to the desired function heat or cool.
⚠ Warning! Read carefully and understand all assembly and operation instructions before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Caution! Do not allow persons to operate or assemble this cooler and warmer until they have read this manual and have developed a thorough understanding of how the cooler and warmer works.
⚠ Warning! The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

ELECTRIC SAFETY INSTRUCTIONS FOR POWER SUPPLY

In order to comply with the safety requirements set forth in several international publications, the following measures must be followed when using this unit:

1. The maximum room temperature around the power supply must not exceed the one indicated on its label.
2. When connecting the unit to the electric supply and to the equipment, respectively, you must check if the voltage is the same indicated in the unit.
3. The consumption of the equipment connected to the source output must not exceed the one indicated in the unit.
4. This product can be used for outdoor, just make sure not make it wet.
5. If the power supply cable is damaged, it must be fixed by the supplier, by its representative or by qualified personnel to avoid danger.
6. If the unit was hit and it is noticed any damage in the protection cover or failures, the unit must not be used and must be fixed exclusively by technically qualified personnel assigned by the product importer and/or legal representative.
7. The equipment must be connected to a visible and easy access socket.
8. This product is not a toy. It is not intended for use by children under 8 years.

IMPORTANT SAFETY PRECAUTIONS

Note: There is a replaceable 10A glass fuse in the cigarette lighter adapter. Replace a blown fuse by gently unscrewing the tip of the lighter plug and inserting in a new one of comparable Amperes rating. Do Not replace fuse with a higher amp rated fuse.

▶ Do not immerse the cooler/warmer 12V plug in water.
▶ Do not insert foreign objects into the cooler/warmer vent openings. The ventilation openings should not be covered at any time while the cooler/warmer is operating.
▶ Do not use the cooler/warmer in the open air when it is raining or snowing; it is not designed to be waterproof.
▶ Do not place cooler/warmer near heat sources: heating vents, radiators, sunlight and/or any other sources of heat.

▶ Do not use the cooler/heater in the presence of flammable fumes or gases, such as propane.

▶ Do not use for cooking.

▶ Do not use for medical reasons or storage of medicine.
▶ Do not operate the cooler/warmer if it has received a sharp blow, been dropped or otherwise damaged in any way.

▶ Do not place liquids or foods in direct contact with this unit.

▶ Keep out of Reach of Children. The interior becomes very hot or cold and could cause injury.

FEATURES

1. Cooling device
2. Plastic lid
3. Connection cable for 12V DC connection
4. Shoulder belt
5. Ventilation slots
6. Control panel

OPERATION

Note: Before starting your new cooling device for the first time, you should clean it inside and outside with a damp cloth for hygienic.

▶ Ensure the main switch is on the Off position.
▶ Start the vehicles engine.
▶ Plug the power cord into the cooler/warmer.
▶ Plug the power cord into the 12V cigarette lighter outlet firmly.
▶ Turn the cooler/warmer on by sliding the main switch to the desired position heat or cool.
The Green LED will be illuminated when cooling and the Red LED will be illuminated when heating.
▶ Place foods/beverages inside the cooler/warmer and close the cover.
▶ Turn the cooler/warmer off by sliding the man switch to the Off position.
The unit will always perform best if filled with foods/beverages that are already cold or warm. For cooling functions, add some ice will help a lot.
▶ Operate unit only with cord provided. Store the cord inside the unit to prevent losing it.

Technical description

The cooler is suitable for mobile use. It can cool goods to max. 18°C (65°F) under the ambient temperature or keep them cool.
Its cooling system is a non-wearing and CFC-free Peltier cooling, the heat is discharged by a fan.

Energy saving tips

▶ Choose a well ventilated installation location which is protected against direct sunlight.
▶ Allow warm food to cool down first before placing it in the device to keep cool.

▶ Do not open the cooling device more often than necessary.

▶ Do not leave the lid open for longer than necessary.

USE AND CARE

▶ Do not modify the cooler/warmer in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which the cooler/warmer was designed.

▶ Always check for damaged or worn out parts before using the cooler/warmer. Broken parts will affect the operation. Replace or repair damaged or worn parts immediately.

▶ When the cooler/warmer is not in use, store it in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use.

Cooler function

This unit will take about 30-60min to cool to 7°C ±2 when ambient temperature is at 25°C. The higher the ambient temperature (Room Temperature) the higher the cooler temperature will be.

▶ Pre-chilled items will assist the fridge to cool down faster.
▶ The cooler will continue to operate as long as the unit is plugged in.
▶ After being unplugged the unit will remain cool for a period of time.
The contents of the unit will come up to room temperature over time and caution should be exercised to ensure food does not spoil.

Warmer function

The unit will take about 30 minutes to warm to 65^ (149^)± 2 , Pre-heated items will assist the warmer to heat up faster.
▶ The warmer will continue to operate as long as the unit is plugged in.
▶ The warmer will automatically cycle on and off to prevent overheating.
▶ After being unplugged the unit will remain warm for a period of time.
The contents of the unit will drop to room temperature over time and caution should be exercised to ensure food does not spoil.

CLEANING AND MAINTENANCE

▶ Switch unit off, unplug power cord and allow it to cool or heat up to room temperature.
▶ Wipe the inside with a clean, damp cloth. Use a mild soap with water if necessary. Do not use abrasive cleaners, scrubbers or household chemicals as this may damage the finish.

▶ Do not immerse the unit in water.

It is recommended that the general condition be examined before it is used. Keep your cooler and warmer in good repair by adopting a program of conscientious repair and maintenance. Have necessary repairs made by qualified service personnel.

TROUBLESHOOTING

Unit does not turn on.

▶ Make sure vehicle is running or the ignition is in the "accessories" position.
▶ Ensure adapter is correctly installed.
▶ Check fuse in the tip of the cigarette lighter adapter.

Replace if needed.

▶ Check fuse for the vehicle cigarette lighter.

Replace if needed.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be disposed of with normal household waste.

Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again.

Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.

For more information about our authorized service centers and if you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you, or visit us at www.BlackandDecker-la.com

SPECIFICATIONS BDC8L-LA

Power 48W at 12V DC

Voltage 12V

Capacity 8 Liters

Warmer Temperature 65°C (149°F)

Cooler Temperature 18°C (65°F) under ambient temperature

Power Cord Cigarette adapter with 10A fuse and 2m cord

Weight 3.19kg

TROUBLESHOOTING

Fault Possible Cause Solution
Your cooler does not function (plug is inserted, LED does not glow after sliding the switch to cool or heat).	There is no voltage flowing from the 12V socket (cigarette lighter) in your vehicle.	The ignition must be switched on in most vehicles for voltage to flow at the cigarette lighter.Try using another plug socket.
Your cooler does not cool (plug is inserted, LED glows).	The inner fan or the cooling element is defective.	This can only be repaired by an authorised customer services unit.
Your cooler does not heat (plug is inserted, LED glows).	The inner fan or the heating element is defective.	This can only be repaired by an authorised customer services unit.
Operation with a 12V socket (Cigarette Lighter): The ignition is on and the cooler is not working.Pull the plug out of the socket and make the following checks.	The cigarette lighter socket is dirty. This results in a poor electrical contact. The fuse of the 12V plug has blown. The vehicle fuse has blown.	If the plug of your cooler becomes very warm in the cigarette lighter socket, either the socket must be cleaned or the plug has not been assembled correctly. Replace the fuse (10A) in the 12V plug. Replace the vehicle's 12V socket fuse (usually 15A). (Please refer to the operating manual of your vehicle)

Buenos Aires (B1618FBQ)

CNPJ: 53.296.273/0001-91

Insc. Est.: 701.948.711.00-98

S.A.C.: 0800-703-4644

Solamente para propósitos de Colombia