DW366 - Saw DEWALT - Free user manual and instructions
Find the device manual for free DW366 DEWALT in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Circular Saw |
| Brand | DeWalt |
| Model | DW366 |
| Power Source | Corded Electric |
| Motor | 15 Amp |
| No Load Speed | 5,200 RPM |
| Blade Diameter | 7-1/4 inches (184 mm) |
| Arbor Size | 5/8 inch |
| Bevel Capacity | 0° to 50° |
| Depth of Cut at 90° | 2-1/2 inches (63.5 mm) |
| Depth of Cut at 45° | 1-7/8 inches (47.6 mm) |
| Weight | 10.5 lbs (4.8 kg) |
| Dimensions (L x W x H) | 12.5 x 10.5 x 10 inches |
| Dust Extraction | Yes, with dust port |
| Electric Brake | Yes |
| Safety Features | Blade guard, lock-off switch |
| Maintenance | Regular cleaning, brush replacement |
| Repairability | Replaceable brushes, armature, field |
| Warranty | 1 year limited |
Frequently Asked Questions - DW366 DEWALT
How do I change the blade on the DeWalt DW366?
Unplug the saw, press the spindle lock button, use the provided wrench to loosen the arbor bolt (turn counterclockwise). Remove the outer washer and blade. Install new blade with teeth facing forward, tighten bolt securely.
What is the maximum depth of cut at 90 degrees?
The maximum depth of cut at 90° is 2-1/2 inches (63.5 mm). At 45°, it is 1-7/8 inches (47.6 mm).
Can I use a 6-1/2 inch blade on the DW366?
No, the DW366 is designed for 7-1/4 inch blades with a 5/8 inch arbor. Using a smaller blade is unsafe and may cause kickback.
How do I adjust the bevel angle?
Loosen the bevel adjustment lever (located near the base), tilt the saw to desired angle (0-50°), and retighten the lever. Use the bevel scale for precise settings.
Why does my saw bind or kick back?
Common causes: a dull blade, improper alignment, or forcing the saw. Ensure the blade is sharp and the riving knife (if equipped) is properly adjusted. Let the saw do the work.
How do I clean the dust port?
Unplug the saw. Remove the dust port cover (if any) and use a brush or compressed air to clear debris. Avoid using water or solvents that could damage electrical components.
What is the correct blade orientation?
The blade teeth must face forward (toward the direction of cut). The arrow on the blade should point in the same direction as the blade rotation arrow on the saw.
How often should I replace the carbon brushes?
Inspect brushes every 50 hours of use or if sparking excessively. Replace when worn to less than 1/4 inch (6 mm). Always use genuine DeWalt brushes.
Can I use the saw for wet cutting?
No, the DeWalt DW366 is not designed for wet cutting. Using water increases risk of electric shock and motor damage.
Where is the serial number located?
The serial number is on the black label attached to the motor housing. It starts with 'DW366' followed by a sequence of numbers.
User questions about DW366 DEWALT
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Saw in PDF format for free! Find your manual DW366 - DEWALT and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DW366 by DEWALT.
USER MANUAL DW366 DEWALT
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : DEWALT
Model : DW366
Category : Saw