WL4030 - Home Automation HAGER - Free user manual and instructions

Brand	Hager
Model	WL4030
Product Type	Dimmer Switch
Application	Home Automation
Load Type	Ohmic (Resistive)
Power Rating	60-300 W
Nominal Voltage	230 V AC, 50 Hz
Fuse Rating	2.5 A
Protection Degree	IP20
Control Modes	Manual and Remote (Infrared)
Dimming Adjustment	Continuous press and hold
Last Intensity Memory	Yes
LED Indication	Flashes at min/max intensity and during programming
Compatible Lamps	Filament and Halogen only
Incompatible Lamps	LED, CFL, transformers
Assembly	Pull button, connect wires per diagram, fix base, replace buttons
Safety Precautions	Disconnect voltage; qualified personnel only
Troubleshooting	Check lamp and fuse
Maintenance	Replace fuse with same type and value

Frequently Asked Questions - WL4030 HAGER

How to install the Hager WL4030 dimmer?

Pull the button (1). Connect wires properly following wiring diagram. Fix the base (3) into the wall, then replace buttons (1) and (2) onto the base. Ensure voltage is disconnected before installation.

How to use manual dimming?

Briefly press button (1) instantly to turn on/off. Press and hold the button to continuously increase/decrease light intensity. Release at desired level. The LED flashes at min and max intensity.

How to set remote control mode?

With light off, press button (1) for about 10 seconds until the dimmer LED signals. Then press any key of an Infra Red Remote Controller (IRRC) towards the dimmer; the light turns on and the key is memorized.

What types of lamps are compatible with this dimmer?

Only filament or halogen lamps. Do not use energy-saving, LED, fluorescent lamps, or transformers.

What should I do if the dimmer stops working?

Check the connected incandescent lamp and the built-in fuse. If required, replace fuse with the same fuse value and type (2.5 A).

How to replace the fuse in the dimmer?

Disconnect voltage supply. Open the dimmer, locate the fuse, and replace it with a 2.5 A fuse of the same type. Only qualified personnel should perform this.

What does the LED indicator signify?

The LED on the button flashes when light intensity is at minimum or maximum. It also signals during remote control programming mode (about 10 seconds press).

Can I use LED bulbs with this dimmer?

No, the manual states: 'Do not use with energy-saving, LED, fluorescent lamps, transformers'. Only filament or halogen lamps are allowed.

What safety precautions should I take?

Work on 230 V~ network must be done by qualified personnel with voltage supply disconnected. Read instructions before use.

Does the dimmer remember the last light intensity?

Yes, the light intensity will be the same as last intensity when you turn it on each time, both in manual and remote modes.

USER MANUAL WL4030 HAGER

Close-up of a square electrical switch or socket component with mounting flanges and a central screw-like feature (no text or symbols visible)

Exploded view diagram of a device showing internal components and assembly (no text or symbols)

Pure electrical circuit lines without any symbols

Work on 230 V\~ network can only be carried out be people with applicable qualifications. All work should be done with the voltage supply disconnected.

• Before use read this intructions.
• Use only filament or halogen lamps
• Do not use with energy-saving, LED, fluorecant lamps, transformers

Assembly

• Pull the button ① (Rys. 1)
• Connect the wires properly
• For operating correctly follow wiring diagram (Rys. 2) and technical specifications
• Fix the base ③ into the wall
• Replace the button ① and ② onto the base ③

Manual mode operation

• For turning on/off the light, push the button ① instantly
• For adjusting the intensity of the light, press the button for a while. So the intensity of light increases and decreases continuously. Which intensity is desired you unpress the button.
• LED which is on the button flashes when the light intensity is at min. and max. level
• The light intensity will be same as last intensity when you turn on each time.

Remote control mode operation

• When the light is off press the button about 10 sec. till the dimmer LED signals
• If you press any key of IRRC* to the dimmer while the dimmer LED is signalling the light turns on. This means the key which you pressed is memorized
• For turning on/off the light, press the key of IRRC instantly
• For adjusting the intensity of the light, press the key of IRRC for a while. So the intensity of light increases and decreases continuously. Which intensity is desired you unpress the key.
• LED which is on the button flashes when the light intensity is at min. and max. level
• The light intensity will be same as last intensity when you turn on each time.
• When you press wrong key the dimmer LED signals and dimmer does not operate.
• If you forget which key you memorized then you can new one memorized as above mentioned

*IRRC: Infra Red Remote Controller (any universal one)

In case of malfunction

Should the dimmer no longer function, please check the connected incandescent lamp or the fuse installed in the dimmer. If required, replace fuse by same fuse value and type only!

Technical specifications

Load	Ohmic
Power	60-300 W
Nominal Voltage	230 V AC/50 Hz
Fuse	2,5 A
Protection Degree	IP20

PL Instrukcja