HP24TS-4-2L-2A - Beer dispenser Perlick - Free user manual and instructions

Product Type	Beer Dispenser (Undercounter)
Brand	Perlick
Model	HP24TS-4-2L-2A
Dimensions (W x D x H)	24 x 24 x 16 inches (approx.)
Weight	80 lbs (approx.)
Power Supply	115V, 60Hz, 1.5A (typical)
Number of Taps	4
Cooling Type	Forced air or glycol (not specified)
CO2 System	Included (cylinder not included)
Cleaning Frequency	Every 2 weeks or after each keg
Cleaning Supplies Needed	Cleaning kit (Part No. 63797), warm water, cleaning chemical (BLC)
Faucet Type	Standard beer faucet (removable with spanner wrench)
Coupler Type	Low profile coupler (no check ball) or standard with check ball
Safety Precautions	Handle cleaning chemicals with care; turn off CO2 before cleaning
Spare Parts Availability	Faucets, couplers, cleaning kits, seals available
Repairability	User-serviceable: faucet removal, line cleaning; professional service for cooling system
Material	Stainless steel (tower and body)
Installation Type	Undercounter or built-in
Included Accessories	Cleaning kit (pump jar, washer, chemical, brush, spanner wrench)
Manual Language	English (available for download)

Frequently Asked Questions - HP24TS-4-2L-2A Perlick

How often should I clean the Perlick HP24TS-4-2L-2A beer dispenser?

It is recommended to clean the system after every barrel or every two weeks to prevent bacteria, yeast, and beer stone buildup.

What supplies do I need for cleaning?

You need a cleaning kit (Part No. 63797) which includes a cleaning pump jar, coupling washer, BLC line cleaning chemical, check ball lifter, cleaning brush, and spanner wrench, along with warm and cold water and buckets.

How do I remove the beer faucet for cleaning?

Use a spanner wrench to unscrew the faucet from the dispensing head. Refer to the faucet manufacturer's instructions for disassembly.

Do I need to turn off CO2 before cleaning?

Yes, always turn off the CO2 at the cylinder or air distributor to prevent gas flow during cleaning.

What is the cleaning solution mix ratio?

Follow the instructions on the cleaning chemical container. Typically, mix the chemical with warm water as per the recommended dilution.

How long should the cleaning solution sit in the lines?

After pumping half the solution through, let it stand for 15 minutes, then pump the remaining solution through.

How do I clean the faucet components?

Disassemble the faucet, soak the parts in a cleaning solution for 15 minutes, scrub with a cleaning brush, rinse with clean water, and check seals for wear.

What should I do if the coupler has a check ball?

Insert a check ball lifter into the bottom of the coupler to hold the ball open during cleaning. The Perlick Low Profile Coupler does not have a check ball.

How do I reassemble the system after cleaning?

Reattach the faucet using a spanner wrench, reconnect the coupler to the keg, turn on CO2, and tap the new keg.

Where can I find replacement parts or the cleaning kit?

The cleaning kit is part number 63797. Replacement parts such as faucets, couplers, and seals are available from Perlick or authorized dealers.

USER MANUAL HP24TS-4-2L-2A Perlick

CLEANING INSTRUCTIONS

To ensure brewery-fresh flavor, it is recommended that the beer system be cleaned after every barrel or every two weeks to eliminate bacteria, yeast and beer stone build-up in the system. Below, you'll find instructions on how to properly and thoroughly clean your beer dispenser.

SUPPLIES NEEDED:

- Cleaning Kit - Includes cleaning pump jar (A), coupling washer (B), 4 oz. BLC line cleaning chemical (C), check ball lifter (D), cleaning brush (E) and spanner wrench (F) (Kit Part No. 63797, shown right)

• Buckets
  • Water (warm and cold)

CAUTION: The chemicals used to clean beer lines are hazardous. Please follow all recommended safety instructions on the chemical's container.

1. Turn off the CO 2, either at the CO2 cylinder or at the air distributor.
2. Remove tapping device (keg coupler) from the barrel.
3. If tapping device contains a check ball, insert check ball lifter into the bottom of the coupler (Perlick Low Profile Coupler does not contain a check ball).
4. Place tapping device into a small bucket.
5. Using a spanner wrench, remove the beer faucet from the dispensing head.
6. Fill cleaning pump with warm water.
7. Attach cleaning pump jar connector with washer to where faucet was removed from dispensing head.
8. Pump the warm water through the system to remove all remaining beer from the system. Empty tapping device bucket and rinse out. Place tapping device back into the bucket.
9. Fill cleaning pump jar with water and cleaning chemical per the recommendations on the cleaning chemical container.
10. Pump cleaning solution into system, leaving about a 1/2 the solution in the cleaning pump jar.
11. Let stand 15 minutes, then pump remaining solution through the system
12. Using a cleaning brush, clean the exterior surfaces of the tapping device and rinse with clean fresh water
13. Rinse out cleaning pump jar with fresh water
14. Fill cleaning pump jar with clean warm water and pump entire jar through the system
15. Repeat step 13 using clean cold water
16. During the 15 minutes that the solution is in the system, mix a small container with water and cleaning chemical per the instructions on the clenaing chemical container and disassemble the faucet per faucet manufacturers recommendations and let soak in solution
17. Using cleaning brush, clean the components of the faucet
18. Rinse all components of the faucet in clean fresh water. Check all seals on the faucet for wear and replace if necessary
19. Reassemble faucet
20. Remove cleaning pump jar from dispensing tower connection and reinstall faucet using spanner wrench to tighten properly
21. Turn on CO _2 and tap new keg