Freez - Synthesizer 2hp - Free user manual and instructions
Find the device manual for free Freez 2hp in PDF.
User questions about Freez 2hp
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Synthesizer in PDF format for free! Find your manual Freez - 2hp and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Freez by 2hp.
USER MANUAL Freez 2hp
text_image
Freez IN SIZE TRIG S. RATE OUT 2hpDescription
Freez is a voltage controlled locked looper. It captures moments of audio in buffers, where they can be minced and mangled beyond recognition. Once frozen, adjusting size will cause pitch and timbre changes to the locked audio.
Adjusting the sample rate control will distort and decimate the incoming audio as well as warp the time domain of the currently locked buffer. From beat repeat to granular audio buffer, Freez will create new sounds and textures out of any input signal.
- Voltage controlled locked looper
- Sample rate up to 96kHz
- Buffer size ranges from microseconds to 3 seconds long
- Beat repeat
- Bit crusher
Table of Contents
Installation/Specifications 4
Freez ____ 5
General Functions Overview 6
Installation
To install, locate 2 HP of space in your Eurorack case and confirm the positive 12 volts and negative 12 volts sides of the power distribution lines. Plug the connector into the power distribution board of your case, keeping in mind that the red band corresponds to negative 12 volts. In most systems, the negative 12 volt supply line is at the bottom. The power cable should be connected to the Freez with the red band facing the front of the module.
Specifications
Format: 2 HP Eurorack module
Depth: 47mm (Skiff Friendly)
Max Current: +12V = 95mA
-12V = 27mA
text_image
Freez 1 IN 2 3 SIZE 4 5 6 7 TRIG 8 9 S. RATE 10 OUT 2hp1. IN:
Audio input
Range: 10Vpp
2. SIZE CV INPUT:
Control voltage input for SIZE
Control voltage is added to the knob position
Range: ±5V
3. SIZE:
Controls the length of the buffer that audio is recorded into
If the knob is fully counterclockwise, the audio buffer will be as large as possible If the knob is fully clockwise, the audio buffer will be as small as possible
The length of the buffer is also dependent on the S. RATE control
Range: 9ms - 3s
4. FREEZ LED:
Indication of the Freez state
If the FREEZ LED is illuminated, the incoming audio signal will be frozen If the FREEZ LED is unilluminated, the dry audio signal will pass to the output
5. MODE TOGGLE:
Toggle that sets either momentary or latching functionality
If the toggle is in the up position, momentary functionality is selected. If the toggle is in the down position, latching functionality is selected
6. BUTTON:
Button that, when pressed, will either freeze or unfreeze the incoming audio signal based the module's current state and MODE TOGGLE position
When set to momentary functionality, a pressed state of the button will cause the audio buffer to freeze until the button is released
When set to latching functionality, the initial press of the button will cause the audio buffer to freeze or unfreeze based on its current state
7. TRIG:
Trigger input.
When set to momentary functionality, the audio buffer will freeze for the duration of the rising edge signal present at the TRIG input
When set to latching functionality, the audio buffer will either freeze or unfreeze when a rising edge signal is present at the TRIG input based on its current state
8. S. RATE CV INPUT:
Control voltage input for S. RATE
Control voltage is added to the knob position
Range: ±5V
9. S. RATE:
Controls the sample rate of the audio buffer
If the knob is fully counterclockwise, the sample rate will be as low as possible If the knob is fully clockwise, the sample rate will be as high as possible
Range: 2.36kHz - 96kHz
10. OUT:
Audio output
Range: 10Vpp