OH 150 - Tripod Glide Gear - Free user manual and instructions

Product Type	Photography Tripod
Brand	Glide Gear
Model	OH 150
Maximum Height	60 inches (152 cm)
Minimum Height	20 inches (51 cm)
Folded Length	25 inches (63.5 cm)
Weight Capacity	10 lbs (4.5 kg)
Weight	3.5 lbs (1.6 kg)
Material	Aluminum alloy legs, plastic head
Leg Sections	3 sections with flip locks
Head Type	Pan/tilt head with handle
Quick Release Plate	Yes, with 1/4 inch screw
Compatible Cameras	DSLR, mirrorless, camcorders up to 10 lbs
Leveling Base	Built-in bubble level
Spreader	Mid-level spreader for stability
Feet	Rubber feet with retractable spikes
Cleaning	Wipe with dry cloth; do not use solvents
Maintenance	Tighten screws periodically; lubricate joints if needed
Safety Warning	Do not exceed weight limit; secure on flat surface
Repairability	Replaceable parts available; contact Glide Gear support
Warranty	1 year limited warranty
Package Includes	Tripod, pan head, quick release plate, carry bag
Manufacturer	Glide Gear

Frequently Asked Questions - OH 150 Glide Gear

How do I attach my camera to the Glide Gear OH 150 tripod?

Use the quick release plate. Screw the plate into your camera's 1/4 inch socket, then slide it onto the tripod head until it clicks. Ensure the safety pin is engaged.

What is the maximum weight capacity of the OH 150?

The OH 150 can support up to 10 lbs (4.5 kg), suitable for most DSLRs and mirrorless cameras with medium lenses.

How do I adjust the height of the tripod legs?

Unlock the flip locks on each leg section, extend to desired height, then close the locks firmly. Adjust all three legs for level setup.

Can I use the OH 150 for video recording?

Yes, the pan/tilt head allows smooth pan and tilt movements, ideal for video. Use the handle for controlled motion.

How do I level the tripod on uneven ground?

Use the built-in bubble level on the head. Adjust leg lengths individually until the bubble is centered.

What is the folded length of the tripod?

The OH 150 folds down to 25 inches (63.5 cm) for easy transport. It comes with a carry bag.

How do I clean and maintain the tripod?

Wipe legs and head with a dry cloth. Avoid solvents. Periodically tighten all screws and apply light lubricant to moving parts if needed.

Can I replace the quick release plate if lost?

Yes, replacement plates are available from Glide Gear or third-party sellers. Ensure the plate is compatible with the OH 150 head.

What should I do if the head becomes loose?

Check the tension knobs on the head. Tighten them as needed. If the issue persists, consult the manual or contact Glide Gear support.

Is the OH 150 suitable for outdoor use in wind?

The tripod's rubber feet and mid-level spreader provide decent stability. In strong wind, hang a weight (e.g., camera bag) from the center hook for extra stability.

USER MANUAL OH 150 Glide Gear

(1) The OH 150 includes 2 kinds of spacers:

• 2x Track Holders: the end caps are facing in the opposite direction than the plate with the 1/4-20 and 3/8-16 mounting holes.
• 3x Accessory Holders: the end caps are facing in the same direction than the plate with the 1/4-20 and 3/8-16 mounting holes.

A Track Holder is pictured in Fig A. An Accessory Holder is pictured in Fig. B.

Mechanical assembly diagram showing a vertical support structure with mounting brackets and a green component, labeled Fig. A (no text or symbols on the diagram itself)

(2) Assemble 2 separate track sections of equal length. The OH 150 comes with 6 x 4ft sections so the maximum length for the OH 150 is 12ft (2x 12ft sections). Make sure to secure the connection between each track section using the supplied hardware
(3) Mount the 2 supplied light stand adapters at the bottom of the Track Holders as seen in Fig. A.
(4) Place the 2 Track Holders at the ends of the track. Press in the track into the end caps until you hear a snap.
(5) Mount the supplied camera platform at the bottom of one of the Accessory Holder. See Fig. B.
(6) Place the Accessory Holder at the desired location on along the track. The holder's end caps must be facing down. Make sure the track snaps on the end caps.
(7) The OH 150 comes with the GG 33 ball head. Mount the ball head to the camera platform to adjust the camera angle.
(8) The OH 150 comes with a total of 3 Accessory Holders. Use them to mount multiple cameras, lights, mics, monitors..etc.

Fig. B