BH3130010-1 - Heating Bromic - Free user manual and instructions

Type	Heater
Brand	Bromic
Model	BH3130010-1
Power Source	Electric (120V/240V, 1500W)
Heating Type	Infrared
Heating Area	Up to 250 sq ft (23 sq m)
Adjustable Thermostat	Yes, with remote control
Safety Features	Tip-over switch, overheat protection, IPX4 waterproof
Dimensions (H x W x D)	71.5 x 11.8 x 11.8 in (181.6 x 30 x 30 cm)
Weight	33 lbs (15 kg)
Mounting	Wall-mounted or free-standing with stand (included)
Remote Control	Yes, included
Timer	1-12 hour timer
Material	Stainless steel body with tempered glass front
Color	Black or Silver
Certification	ETL, CE, RoHS
Warranty	2 years limited
Recommended Use	Indoor/outdoor covered areas
Cleaning	Wipe with soft damp cloth; do not use abrasive cleaners
Spare Parts	Heating element, remote control, stand available from Bromic

Frequently Asked Questions - BH3130010-1 Bromic

How do I install the Bromic BH3130010-1 heater?

The heater can be wall-mounted or placed on its stand. For wall mounting, use the provided brackets and secure to a sturdy wall. Ensure clearance of at least 36 inches from combustible materials. Refer to the manual for detailed steps.

What power supply does this heater require?

It operates on 120V or 240V AC, 60Hz, with a maximum power of 1500W. A dedicated circuit is recommended. Check local electrical codes.

Can I use this heater outdoors?

Yes, it is rated IPX4 for water resistance, making it suitable for covered outdoor areas like patios. Avoid direct exposure to rain or snow.

How do I clean the heater?

Turn off and unplug the heater before cleaning. Wipe the exterior with a soft, damp cloth. Do not use chemicals or abrasive materials. Clean the glass gently.

What safety features does it have?

It includes a tip-over switch that shuts off the heater if knocked over, and an overheat protection system. The front glass is tempered for safety.

Does the heater come with a remote control?

Yes, a remote control is included, allowing you to adjust temperature, timer, and on/off from a distance.

What is the heating area coverage?

It effectively heats up to 250 square feet (23 square meters) in a well-insulated space. Coverage may vary based on room layout and insulation.

How long is the warranty?

Bromic offers a 2-year limited warranty covering manufacturing defects. Register your product online for full warranty details.

Can I replace the heating element?

Yes, the heating element is replaceable. Contact Bromic customer service or an authorized dealer to purchase a replacement. Professional installation is recommended.

Why is my heater not turning on?

Check that the power cord is plugged in and the circuit breaker hasn't tripped. Ensure the remote control batteries are fresh. If the tip-over switch is activated, place the heater on a stable surface. If still not working, contact support.

USER MANUAL BH3130010-1 Bromic

Exterior view of a gray rectangular electronic device with four circular ports (no text or symbols visible)

IMPORTANT

READ THIS MANUAL CAREFULLY.

SEE INSIDE COVER FOR IMPORTANT

INFORMATION ABOUT THIS MANUAL. KEEP

INSTRUCTION WITH APPLIANCE FOR FUTURE

REFERENCE.

This manual contains important information about the installation, and operation of Tungsten Electric controller. Please pay close attention to the important safety information shown throughout this instruction manual. Any safety information will be accompanied by the following safety alert symbols:

⚠️DANGER, ⚠️WARNING, ⚠️IMPORTANT

• READ THIS MANUAL CAREFULLY before installing or servicing this product.
• Improper installation or operation can result in death, severe injury, or property damage.
• Use this controller only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons
• This controller is intended for fixed installation with 110 - 230 volt power supply.
• Installation MUST be carried out by a licensed and authorised technician in accordance with local electrical codes.
• For Commercial Use Only

NOTE: IMPORTANT INSTRUCTIONS, SAVE THESE INSTRUCTIONS

WARNING

• WARNING: The outputs are NOT protected against short circuits or extra-currents which can damage the electronic board. Evaluate the characteristics of the connected loads and apply the appropriate safety devices to the power line.
• The radio signal reception of the device can be affected by the presence of electrical disturbances being transmitted by other appliances working on the same frequency or if the product is shielded by metal parts.
• Do not use the remote in places where systems are sensitive to radio emissions.
• Do not keep or use the remote in places that are damp, where there is steam, high air humidity, dust or where it is exposed to direct sunlight or similar environmental conditions.
• Do not drop the remote. This could damage or reduce the range of action of the remote.
• Do not use your nails to press remote buttons.
• Keep remote batteries out of reach of children.
• Call a doctor immediately if a battery is swallowed.
• See remote instruction manual for more details on the included remote.

BROMIC

HEATING

BROMIC HEATING

Head Office: 1 Suttor Street, Silverwater, Sydney, NSW 2128 Australia

Telephone: [phone] (within Australia) or [phone] (from overseas) Fax: [phone]

Email: [e-mail] Web: www.bromicheating.com

Note: Bromic Heating reserves the right to make changes to specifications, parts, components and equipment without prior notification. This Installation, operation and service manual may not be reproduced in any form with prior written consent from Bromic Heating.

Manufactured by Teleco Automation s.r.l. - Italy - www.telecoautomation.com

CONTENTS

IMPORTANT NOTES & WARNINGS 4

PRODUCT OVERVIEW 5

• Read all instructions before installing or using this heater
• Use this controller only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• Improper installation, adjustment, or alteration and failure to follow the warnings and instructions in this manual could result in severe personal injury, death or property damage.
• The manufacturer is not responsible for any damage that could happen from improper use. The manufacturer emphasises that this controller should be used in a responsible manner and that all procedures, warnings, and safety instructions contained in this booklet be followed strictly.
• The product must be fixed on surfaces which cannot be damaged by the high temperature. It must be placed in a well ventilated location. It cannot be hermetically closed. It must be fixed vertically, with cable glands downward.
• The connection cables must be protected against any accidental impacts, using proper pipes.
• This controller is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate controller where it may fall into a bathtub or other water container.
• Do not install the controller directly near a bathtub, shower or swimming pool. Any switches or controls must not be within reach of a person in the bathtub, shower or swimming pool.
• Extreme caution is necessary when any controller is used by or near children or invalids and whenever the controller or heater is left operating and unattended.
• This controller is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Keep packaging materials out of reach of children
  • Children and adults should be alerted to the hazards of electrocution and should stay away to avoid serious personal injury
• Children should be carefully supervised when they are in the area of the controller.
• Do not attempt to alter the controller in any manner.
• Do not paint any surface of the controller.
• Do not touch the controller with wet hands at any time.
• Do not use or store flammable materials near this appliance.
• Do not spray aerosols or flammable materials in the vicinity of the controller while it is in operation
• Never operate the controller in an explosive environment such as areas where petrol or other flammable liquids or vapours are stored.

INSTALLATION

• IMPORTANT - Installation must be carried out by a licensed and authorised person.
• The installer is to ensure that the requirements of the local authority, local electrical installation code, municipal building codes, and any other relevant statutory regulations are carried out.
• After unpacking, make sure the controller shows no signs of visible damage or tampering. If the controller appears damaged, contact the place of purchase for assistance.

• Remove transit protection before use.

• This appliance must only be used on a 110 - 230 Volt AC Single Phase electricity supply.

• This controller is NOT intended to be installed on recreational vehicles and/or boats.
• Do not run cord under carpeting. Do not cover with throw rugs, runners or the like arrange cord away from traffic area and where it will not be tripped over
• A controller has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.
• This Installation and Operation manual should not be removed from the site of installation. Installer should leave manual with the customer for future reference.
• Any guard or other protective device removed for servicing (conducted by an authorised person) must be replaced before operating the controller.
• If the controller has not been used, or will not be used, for a long period of time, disconnect power supply
• For the disconnection from the power line, use an all-pole switch with contacts having a dimension of at least 3.5mm.

MAINTENANCE/ REPAIR

• Installation and repair must be carried out by a qualified & licenced service person only. The controller should be inspected before use and at least annually serviced & inspected by a qualified & licenced service person.
• Do not perform maintenance until controller has been turned off and power disconnected.
• Check for damage to the controller regularly. If damage to the appliance is suspected, discontinue use immediately and contact the supplier or qualified person to repair.
• If the supply cord is damaged, it must be replaced by an authorised and licenced person in order to avoid a hazard.
• At the end of this product's useful life, it must not be disposed of as domestic waste, but must be taken to a collection centre for waste electrical and electronic equipment. It is the user's responsibility to dispose of this appliance through the appropriate channels at the end of its useful life. Failure to do so may incur the penalties established by laws governing waste disposal. Proper differential collection and the subsequent recycling, processing and environmentally compatible disposal of waste equipment avoids unnecessary damage to the environment and possible related health risks, and also promotes recycling of the materials used in the appliance. For further information on waste collection and disposal, contact your local waste disposal service, or the place of purchase

ELECTRICAL CONNECTIONS

• All connections must be rated for a single-phase 110 - 230VAC power supply, with an earth connection.
• Arrange all the necessary safety devices and use only materials that comply with standard electrical installations.
• Signal and power voltage wiring (110 - 230Vac) must be separated one from the other.
• The cable must have a section properly rated according to the load connected and nominal temperature range up to 90°C.

PRODUCT OVERVIEW & INSTALLATION

1 DESCRIPTION

The Wireless ON/OFF control is for resistive and infrared heaters. The controller allows the power output of the heater to be turned on/off, impulsive or timer controlled. The wireless control can be used with 110 - 230VAC supply voltages.

1.1 FEATURES

• Controls TWO 3000W heaters at 230VAC (1500W at 110VAC).
• Programmable relay functions: ON/OFF, impulsive and timer controlled up to 8hours, 59minutes and 59seconds.
• Wireless controller enclosed in a protective box.
• 4-channel remote

1.2KITCONTENTS

2.1 INSTALLATION

Study the WIRING DIAGRAM at the end of this document before starting installation.

WARNING: Isolate mains before installing. Use only on with a properly secured heater.

PLUG AND SUPPLY CORD: Use an appropriately rated plug and supply cord - check the power requirements of the connected loads. Socket outlet used must be near the equipment.

OVERCURRENT DEVICE: The outputs are NOT protected against short circuits or extra-currents which can damage the electronic board. Evaluate the characteristics of the connected loads and apply the appropriate safety devices to the power line.

The wireless control must be mounted using the following guidelines:

• It must be fixed on surfaces which cannot be damaged by high temperature.
• It must be placed in a well-ventilated location.
• It must be fixed vertically, with cable glands downward.
• Connection cables must be protected against any accidental impacts, using proper pipes.
• Do not cover the product.

• Do not use or store flammable materials close to the product.

• Open cover to the box.

• Wire in power and heater as per the wiring diagram.
• Power on the wireless control.
• Program the wireless control as per 'OPERATION' section.
• Refit cover to the box.

2.2 OPERATION

Before programming, select the output L1 or L2, using the switch as outlined in the 'WIRING DIAGRAM'.

The following programming will be ONLY applied to the selected output.

It is possible to associate a single or double channel function to both of the outputs by repeating the procedure.

WARNING: The receiver automatically saves the setting 5 seconds after button release.

IMPORTANT: The included 4-channel remote functions as a 4 x single channel remote OR a 2 x double channel remote (paired Ch1 with Ch2 and Ch3 with Ch4). Functions are:

Single Channel Functions - On/Off with the same button

Double Channel Functions – On with Ch1 or Ch3. Off with Ch2 or Ch4

2.2.1 Setting relay function (on/off, impulse, timer)

IMPULSE FUNCTIONPress the ‘SET’ button once and hold it down until the ‘IMP’ LED turns on. Wait until the LED turns off to confirm the memorisation of the data.
ON/OFF FunctionPress the ‘SET’ button twice and hold it down until the ‘ON-OFF’ LED turns on. Wait until the LED turns off to confirm the memorisation of the data.
TIMER FunctionSetting the seconds (1 - 59)The starting value of the seconds is 1.a) Press the ‘SET’ button three times and hold it down until the ‘SEC’ LED will turn on.b) Adjust the seconds by increasing with ‘MEM’ button or decreasing with ‘DEL’ button. Each adjustment is recognised by a flash of the ‘SEC’ LED button.Wait until the led turns off or proceed with the next timer setting.Setting the minutes (1 - 59)The starting value of the minutes is 1.c) Press the ‘SET’ button another time within 5 s. and hold it down until the ‘MIN’ LED will turn on.d) Adjust the minutes by increasing with ‘MEM’ button or decreasing with ‘DEL’ button. Each adjustment is recognised by a flash of the ‘MIN’ LED button.Wait until the led turns off or proceed with the next timer setting.Setting the hours (1 - 8)The starting value of the minutes is 1.e) Press the ‘SET’ button another time within 5 s. and hold it down until the ‘HOU’ LED will turn on.f) Adjust the hours by increasing with ‘MEM’ button or decreasing with ‘DEL’ button. Each adjustment is recognised by a flash of the ‘HOU’ LED button.Wait until the led turns off or proceed with the next timer setting.NOTE: Once the maximum or minimum limits is reached the value will no longer be increased or decreased. Start over from ‘a’) to continue working on the timer function. Starting over will clear the last known programming of the timer.

The following is a brief explanation of each function:

IMPULSE - Heater is only turned on while holding a programmed remote.

ON/OFF - Heater is turned ON or OFF at each button press of a programmed remote.

TIMER - Heater is turned ON for a set duration that the function is programmed to. It is possible to override the

TIMER function by a button press of a programmed remote.

OPERATION

Before starting select the output L1 or L2, using the switch (see picture at page 9). The following memorization/deletion will be applied only to the selected output. Anyway it's possible to associate a double channel to both of the output, repeating the procedure.

2.2.2 Programming of a double channel

1. Press the 'MEM' button two times and hold the button on the second time. There will be 2 beeps and followed by a continuous sound.
2. While holding 'MEM' the button (during continuous sound), press the button on the remote that will be programmed. The programming is confirmed by an intermittent sound.

Note: in case of commanding an output with TIMER function, it's possible to stop the counter before the set time using buttons CH2, CH4 or CH7.

2.2.3 Copying a function of remote to a new remote. See remote manual for detail on P3 button.

1. Press the P3 button inside the already programmed remote. The active receiver will sound continuously. If there is no sound, the remote is not programmed into the receiver.
2. Within 5 seconds, press a button of the already programmed remote, relative to the function to copy. The sound will be interrupted, and continue for another 5 seconds.
3. During the sound, press a button of the new remote that requires to be programmed. The programming is indicated by an intermittent sound.

2.2.4 Deleting a double channel function from the receiver

1. Press the P2 button once and hold it down. There will be a slow and intermittent sound.
2. During the sound, press the button of the remote that will be deleted. The deletion is indicted by a continuous sound.

2.2.5 Deleting all remotes

1. Press the P2 button two times and hold the P2 button on the second time until the following sound sequence is heard.

a. The will be one beep and then followed by a quick and intermittent sound.

b. Continuous sound.

1. Hearing the sound sequence above indicates that the whole memory of the receiver is deleted.

OPERATION

2.2.6 Deleting a remote from a remote. See remote manual for detail on P3 button.

1. Press the P3 button inside the remote three times. There will be slow and intermittent sound.

2. During the intermittent sound, press a button of the remote relative to the function to be deleted. The deletion is indicated by a continuous sound.

2.3 RECOMMENDED PROGRAMMING

The recommended programming for the 4-channel remote is as follows:

• Ch1 & Ch2 to be used as a DOUBLE CHANNEL FUNCTION for output L1
• Ch3 & Ch4 to be used as a DOUBLE CHANNEL FUNCTION for output L2

TECHNICAL SPECIFICATION

WIRELESS CONTROLLER

Power Supply 110/230VAC, 28A
Max Output Power 3000W each relay @ 230VAC1500W each relay @ 110VAC
Reception Frequency 916MHz
Operating Temperature Range -20/+50°C
Maximum Remotes Memorised 42
Dimensions 205 x 145 x 85mm
Protection Class IP54

Manufactured by Teleco Automation s.r.l. - Italy - www.telecoautomation.com

The manufacturer reserves the right to modify design features and technical data without notice.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE	REMEDY
Control box does not receive signals from remote	No battery in remote	Change/Replace with CR2430 battery.
	Control box memory full	Delete a remote from control box memory.
	Remote not programmed into control box	Program remote as per ‘2.2 OPERATION’ section.
All other		Contact your dealer or qualified technician.