XS-HL620 - Car Speaker SONY - Free user manual and instructions

Product Type	Car Speaker
Model	XS-HL620
Brand	Sony
Speaker Size	6.5 inches (165 mm)
Speaker Type	Coaxial 2-Way
Peak Power Handling	300 W
RMS Power Handling	50 W
Impedance	4 Ohms
Sensitivity	90 dB
Frequency Response	50 Hz - 20 kHz
Mounting Depth	45 mm (1.77 inches)
Mounting Hole Diameter	140 mm (5.5 inches)
Weight per Speaker	0.8 kg (1.76 lbs)
Magnet Size	80 mm
Cone Material	Polypropylene (PP)
Tweeter Type	Piezo or Balanced Dome
Maintenance	Clean with soft dry cloth; avoid liquids
Safety	Ensure correct polarity and secure mounting
Spare Parts	Contact Sony authorized service centers
General Information	Designed for rear or front door installation in most vehicles

Frequently Asked Questions - XS-HL620 SONY

What is the size of the Sony XS-HL620 speaker?

The Sony XS-HL620 is a 6.5-inch (165 mm) coaxial car speaker.

What is the power handling of this speaker?

It handles 50 watts RMS and 300 watts peak.

What is the impedance of the XS-HL620?

The impedance is 4 ohms, compatible with most car audio systems.

Is the XS-HL620 a component or coaxial speaker?

It is a coaxial speaker with a built-in tweeter for full-range sound.

What is the sensitivity rating?

Sensitivity is 90 dB, ensuring efficient sound output.

What is the frequency response?

Frequency response ranges from 50 Hz to 20 kHz.

How do I install the Sony XS-HL620 speakers?

Mount them in a standard 6.5-inch cutout. Ensure proper wiring polarity and secure with screws. Refer to the vehicle manual for panel removal.

Can I use these speakers with my factory radio?

Yes, they are 4-ohm and work with most factory or aftermarket head units, but an external amplifier is recommended for best performance.

How do I clean the speakers?

Use a soft, dry cloth to wipe the grille and cone. Avoid liquids or harsh chemicals.

Where can I find spare parts or service?

Contact Sony authorized service centers or visit Sony’s support website for replacement parts.

USER MANUAL XS-HL620 SONY

Specifications Speaker

Separate type, 2 way

Woofer 16 cm (6 1 / 2 in.),composite polypropylene cone type

Tweeter 2.5 cm (1 in.), Soft dome type

Maximum input power

(£C)

100 watts

30 W

4 ohms

90 dB/W/m

30-30,000Hz

6,000 Hz, -6 dB/oct

Woofer: Approx. 690 g (1 lb 10

100 watts

30 W

4 ohms

90 dB/W/m

30-30,000Hz

6,000 Hz, -6 dB/oct

Woofer: Approx. 690 g (1 lb 10

Rated input power

100 watts

30 W

4 ohms

90 dB/W/m

30-30,000Hz

6,000 Hz, -6 dB/oct

Woofer: Approx. 690 g (1 lb 10

Impedance

4 ohms

90 dB/W/m

30-30,000Hz

6,000 Hz, -6 dB/oct

Woofer: Approx. 690 g (1 lb 10

Sensitivity

4 ohms

90 dB/W/m

30-30,000Hz

6,000 Hz, -6 dB/oct

Woofer: Approx. 690 g (1 lb 10

Frequency response

30-30,000Hz

6,000 Hz, -6 dB/oct

Woofer: Approx. 690 g (1 lb 10

Crossover Weight

6,000 Hz, -6 dB/oc

Woofer: Approx. 690 g (1 lb 10

(oz.) per speaker

Tweeter:Approx. 75 g (2.5 oz.)

(oz.) per speaker

Tweeter:Approx. 75 g (2.5 oz.)

pur speaker

Passive speech (see Table)

Passive crossover network:

Approx. 200 g (7 oz.)

Design and specifications subject to change without notice.

Sony Corporation © 1994 Printed in Hong Kong

Dimensions	Unit: mm (in.)
Dimensions	Unité: mm (po.)
Abmessungen	Einheit: mm
Dimensiones	Unidad: mm
Afmetingen	Eenheid: mm
Dimensioni	Unità: mm
Dimensões	Unidade: mm
尺寸	單位: mm

Tweeter

Haut-parleur des aigus

Hochtöner

Altavoz de agudos

Hogetonen-luidspreker

Tweeter

Altifalante de agudos

高音揚聲器

Features

• The tweeter and the woofer can be mounted on separate locations.
• The 16 cm (6 1/2 in.) woofer reproduces rich and powerful bass especially suitable for digital audio source reproduction.
• Only the tweeter: Choice of some mounting locations, on the front door panels or inside the dashboard. • High quality passive crossover network supplied.

Special features

1 First twist the lead ends which will be connected to the passive crossover network, then pull off the insulation.

2 Insert the bare speaker wires into the cavities in accordance with the connection guide on the upper surface of the network body, and firmly tighten the screws with a flat tip screwdriver.

3 Install the network with the connected leads facing down.

Double-sided adhesive tape (not supplied)

Double-sided adhesive tape (not supplied)

Flat mounting

1 Unit: mm (in.)

2 Decide the direction of the unit.

4 Set the marked position to one of the projected part ⑦, then turn clockwise.

Slant mounting

1 Unit: mm (in.)

2 Decide the direction of the unit.

4 Set the marked position to one of the projected part ⑦, then turn clockwise.

Woofer

How to remove the grille net

Precautions

• Be careful not to drive the speaker system continuously with the power exceeding the power handling capacity.
• Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to prevent their possible damage caused by the magnets in the speakers.

Caution

When using the speakers with an amplifier or power booster employing the BTL (balanced transformerless) system, be sure to connect the cords of the speaker system directly to the amplifier speaker cords. If the connection is made through already existing speaker leads which have a common lead for both the right and left channels, it is possible that no sound will be heard and that the amplifier will be damaged.