FP-1/32 - Paint gun Paasche - Free user manual and instructions

Product Type	Flow Pencil (Striping Tool)
Brand	Paasche
Model	FP-1/32
Total Length	5.5 inches (14 cm)
Included Nib Sizes	LN-1/32 (assembled), LN-1/64, LN-3/64, LN-1/16 (loose)
Nib Identification	1 groove (1/64), 2 grooves (1/32), 3 grooves (3/64), 4 grooves (1/16)
HAPK Kit Nib	Comes with one size nib only (varies by kit)
Materials	Aluminum, Brass, Stainless Steel, FDA Approved Silicone
Flow Adjustment	MU-72 Adjusting Screw controls stroke of MU-65 Finger Lever
Color Cup Capacity	Standard cup (FP-6) with removable cover (FP-10)
Vent Hole	Located in FP-10 Cover; must be kept open
Needle Removal	Unscrew MU-71 Handle, remove spring, loosen VL-141 Locknut, pull MU-49L Needle
Packing Replacement	PTFE Packing-#6; tighten or replace using screwdriver on Packing Nut
Cleaning	Empty cup, rinse with solvent, pull lever to flush; use toothpick for hardened paint
Operation Technique	Hold like pencil, pull lever, move backward (away from paint)
Safety Precautions	Use in well-ventilated area; avoid inhaling or skin contact with striping materials
Stand Included	MU-77 Stand (optional pressure cup FP-45 available)

Frequently Asked Questions - FP-1/32 Paasche

How do I adjust the paint flow on my Paasche FP-1/32?

Turn the MU-72 Adjusting Screw to control the stroke of the MU-65 Finger Lever, which regulates the color flow. Turn clockwise for less flow, counterclockwise for more.

What nib sizes are included with the FP-1/32?

The FP-1/32 comes with an LN-1/32 nib assembled and loose nibs in sizes LN-1/64, LN-3/64, and LN-1/16. The HAPK kit includes only one size nib.

How do I identify which nib size I have?

Nibs are grooved: LN-1/64 has 1 groove, LN-1/32 has 2, LN-3/64 has 3, and LN-1/16 has 4 grooves.

How do I clean the FP-1/32 Flow Pencil?

Empty the cup, rinse with solvent, and pull back the MU-65 Finger Lever to flush solvent through. For hardened paint in the nib, use a toothpick or needle dipped in solvent. Remove the needle by unscrewing the MU-71 Handle, removing the spring, and loosening the VL-141 Locknut.

How do I replace the PTFE packing?

Use a small screwdriver to remove or tighten the Packing Nut. Press the new PTFE Packing onto the Packing Nut, tighten until snug, then back out half a turn. Insert the needle; adjust until slight resistance is felt, then reassemble.

Can I use the FP-1/32 for fine detail work?

Yes, the Flow Pencil is designed for striping and detail work. Practice on scrap material first to master control. The fine nib (LN-1/64) allows very thin lines.

What safety precautions should I take?

Use in a well-ventilated area. Avoid inhaling fumes or getting paint on skin/eyes. Consult the material safety data sheet (MSDS) for the paint or striping material.

How do I prepare paint for the FP-1/32?

Mix paint to a free-flowing consistency and strain to remove lumps. Do not mix in the cup; use a separate container. Pour only free-flowing color into the cup.

Why is the vent hole important?

The vent hole in the FP-10 Cover allows air to enter the cup, ensuring consistent paint flow. If blocked, the flow may stop or sputter. Keep it open during use.

What tools are included in the HAPK kit?

The HAPK kit includes only one size nib (specific to the kit) and does not include multiple nibs. The standard FP-1/32 model comes with four nib sizes.

USER MANUAL FP-1/32 Paasche

OPERATING INSTRUCTIONS & REPLACEMENT PARTS

WARNING: Striping materials may be harmful if inhaled or allowed to come into contact with the skin or eyes. Consult the product label and Material Safety Data Sheet supplied for the spray material. Follow all safety precautions. CAUTION: Well Ventilated Area Required to remove fumes.

Comes with LN-1/32 (Assembled) and LN-1/64, 3/64, and 1/16 Nibs loose
Total Length of Flow Pencil is 5 -1/2 inches.
HAPK Kit comes with one size nib only

INTRODUCTION:

The FP-1/32 Flow Pencil is used extensively by Designers, Sculptors, Hobbyists, Crafters, Ceramicists, Artists, Furniture Manufacturers, and others to beautify their products. The Flow Pencil is easy to control and operate.

MIXING COLORS:

1. Proper mixing of colors is essential for continuous and uninterrupted striping.
2. Mix colors into a free flowing consistency, strain to remove any lumps.
3. Do not mix color in cup of Flow Pencil, use a separate container and pour into cup only when color flows freely.

COLOR ADJUSTMENTS:

1. Remove FP-10 Cover, and pour premixed free flowing color into cup, then replace cover.
2. Turning the MU-72 Adjusting Screw will control the stroke of the MU-65 Finger Lever Assembly which controls the flow of color.

OPERATION:

1. Hold the FP-1/32 Flow Pencil in your hand as you would a pencil or brush and place your finger lightly over the MU-65 Finger Lever. When ready to stripe, pull back on the MU-65 Finger Lever. The Flow Pencil should be moved in a backward motion (away from the paint) after the color has begun to flow, never push it into the paint.
2. Regulate the flow to the desired feed rate by turning MU-72 Adjusting Screw.
3. Keep vent hole in the FP-10 Cover open.
4. Practice striping before working on finished product.
5. Correct adjustment of controls and skill of operation will result in uninterrupted and continuous striping.

CARE AND CLEANING:

1. Before storing FP-1/32 Flow Pencil clean it thoroughly. Empty remaining color from the cup and rinse it with solvent. Pull back on the MU-65 Finger Lever and allow solvent to flow through cup, shell and nib.
2. If color has hardened in hole of nib use a tooth pick or needle dipped in solvent to remove accumulation.
3. MU-49L Needle is held in position by MU-57 Needle Chuck and VL-141 Locknut. Remove the needle by unscrewing the MU-71 Handle and removing the spring. Loosen the VL-141 Locknut and then remove the needle for cleaning.

ADJUSTING OR REPLACING WORN PACKING WASHER:

1. If PTFE Packing-#6 becomes worn or loose it must be tightened or replaced.
2. You will need a small screwdriver to remove or tighten the Packing Nut.
3. When replacing your PTFE Packing press Packing onto the Packing Nut-#6. Use a small screwdriver to tighten packing nut into shell until it is tight then back out one-half turn, may vary.
4. Now insert needle - you should feel a slight resistance. If too loose or too tight adjust the Packing Nut with screwdriver until you feel some slight resistance.
5. Now completely re-assemble guts of Flow Pencil.

Paasche Airbrush Co.

9511 58th Place

Kenosha, WI 53144

Phone: [phone]

Website: www.paascheairbrush.com

E-Mail: [e-mail]

CAUTION: OVER TIGHTENING CUP WILL

CAUSE TRIGGER TO MALFUNCTION.

FP-1/32 FLOW PENCIL (WITH EXTRA NIBS: LN-1/64, 3/64 AND 1/16)

HAPK KIT comes with one size nib only

Nibs are grooved as follows:

LN-1/64 has one (1) groove

LN-1/32 has two (2) grooves

LN-3/64 has three (3) grooves

LN-1/16 has four (4) grooves

No. Part No. Description

1. *MU-9 Tip Nut

2. **LN-1/32 Nib (1/64, 3/64 & 1/16 Sizes)

3. *MU-48A Shell Assembly

4. **MU-612PTFE Packing & Packing Nut

5. **MU-65 Finger Lever Assembly

6. *FP-10 Basic Cover (only)

11.MU-71 Handle

12.3A-4 "O" Ring

13.**MU-72 Adjusting Screw

14.**MU-57 Needle Chuck

15.***MU-49L Needle

1. **VL-141 Locknut

18.***VL-140 Spring

No. Part No. Description

1. *FP-6 Cup (only) Aluminum

2. MU-77 Stand

3. AE-43 "O" Ring

(OPTIONAL PRESSURE CUP)

1. FP-45 (Complete assembly)

2. **MU-25 Rod & Cap Assembly

3. *MU-69 Nut

4. *FP-5 Pressure Cover (only)

5. MU-26 Spring

6. *FP-9 Piston

7. ****FP-8 (FDA) "O" Ring

8. *FP-6 Cup (only) Aluminum

9. AE-43 "O" Ring (rubber)