HP24TS-4-1L-1 - Beer dispenser Perlick - Free user manual and instructions

Product Type	Beer Dispenser / Kegerator
Brand	Perlick
Model	HP24TS-4-1L-1
Number of Taps	4
Keg Capacity	Up to 4 standard kegs (1/2, 1/4, 1/6)
Cooling System	Forced air compressor
Temperature Range	34°F – 38°F (1°C – 3°C)
Dimensions (W x D x H)	24" x 24" x 34" (61 x 61 x 86 cm)
Weight	Approx. 150 lbs (68 kg)
Power Supply	115V / 60Hz
Energy Consumption	~500 kWh/year
Exterior Material	Stainless steel
Drip Tray	Included, removable
Lighting	Interior LED
Temperature Control	Digital thermostat
Installation	Indoor use only
Maintenance	Regular cleaning of lines, couplers, and drip tray
Safety Features	Lockable door (optional)
Spare Parts Availability	Yes, through authorized dealers
Warranty	1 year limited
Repairability	Service by certified technicians

Frequently Asked Questions - HP24TS-4-1L-1 Perlick

How do I clean the beer lines of my Perlick HP24TS-4-1L-1?

Flush the lines with a cleaning solution (e.g., BLC) followed by fresh water. Disconnect and soak faucets. Repeat every 2 weeks.

What temperature should I set for my kegerator?

Set between 34°F and 38°F (1°C to 3°C) for optimal carbonation and pour quality.

Why is my beer foamy?

Possible causes: warm glass, high pressure, dirty lines, or incorrect temperature. Check and adjust accordingly.

How many kegs can the HP24TS-4-1L-1 hold?

It holds up to 4 standard kegs (half-barrel, quarter-barrel, or sixth-barrel).

What type of gas is required?

Use CO2 with a regulator. Typically set between 10-14 PSI depending on beer style.

How do I install the kegerator?

Place on a level surface, allow 2 inches clearance around for ventilation, plug into a grounded outlet. Let it sit 24 hours before loading kegs.

Can I use this outside?

No, it is designed for indoor use only. Exposure to outdoor elements can damage components.

How often should I replace the CO2 tank?

Depends on usage, but a 5 lb tank lasts 2-3 half-barrel kegs. Check weight or use a gauge.

What is the warranty period?

Perlick offers a 1-year limited warranty on parts and labor for defects.

How do I troubleshoot a click but no start?

Check power supply, circuit breaker, and thermostat setting. If compressor still fails, contact service.

USER MANUAL HP24TS-4-1L-1 Perlick

CLEANING INSTRUCTIONS

To ensure brewery-fresh flavor, it is recommended that the beer system be cleaned after every barrel or every two weeks to eliminate bacteria, yeast and beer stone build-up in the system. Below, you'll find instructions on how to properly and thoroughly clean your beer dispenser.

SUPPLIES NEEDED:

- Cleaning Kit - Includes cleaning pump jar (A), coupling washer (B), 4 oz. BLC line cleaning chemical (C), check ball lifter (D), cleaning brush (E) and spanner wrench (F) (Kit Part No. 63797, shown right)

• Buckets
  • Water (warm and cold)

CAUTION: The chemicals used to clean beer lines are hazardous. Please follow all recommended safety instructions on the chemical's container.

1. Turn off the CO 2, either at the CO2 cylinder or at the air distributor.
2. Remove tapping device (keg coupler) from the barrel.
3. If tapping device contains a check ball, insert check ball lifter into the bottom of the coupler (Perlick Low Profile Coupler does not contain a check ball).
4. Place tapping device into a small bucket.
5. Using a spanner wrench, remove the beer faucet from the dispensing head.
6. Fill cleaning pump with warm water.
7. Attach cleaning pump jar connector with washer to where faucet was removed from dispensing head.
8. Pump the warm water through the system to remove all remaining beer from the system. Empty tapping device bucket and rinse out. Place tapping device back into the bucket.
9. Fill cleaning pump jar with water and cleaning chemical per the recommendations on the cleaning chemical container.
10. Pump cleaning solution into system, leaving about a 1/2 the solution in the cleaning pump jar.
11. Let stand 15 minutes, then pump remaining solution through the system
12. Using a cleaning brush, clean the exterior surfaces of the tapping device and rinse with clean fresh water
13. Rinse out cleaning pump jar with fresh water
14. Fill cleaning pump jar with clean warm water and pump entire jar through the system
15. Repeat step 13 using clean cold water
16. During the 15 minutes that the solution is in the system, mix a small container with water and cleaning chemical per the instructions on the clenaing chemical container and disassemble the faucet per faucet manufacturers recommendations and let soak in solution
17. Using cleaning brush, clean the components of the faucet
18. Rinse all components of the faucet in clean fresh water. Check all seals on the faucet for wear and replace if necessary
19. Reassemble faucet
20. Remove cleaning pump jar from dispensing tower connection and reinstall faucet using spanner wrench to tighten properly
21. Turn on CO _2 and tap new keg