WH128 150.567 - Light effect machine BeamZ - Free user manual and instructions

Product Type	Light Effect Machine
Brand / Model	BeamZ WH128 150.567
Dimensions	398 x 220 x 289 mm
Weight	17.5 kg
Power Supply	220-240 VAC / 50 Hz
Power Consumption	115 W
LED Type	12 x 8W Quad LEDs (RGBW)
DMX Channel Modes	1, 4, or 8 channels
IP Rating	IP65 (dust and water resistant)
Light Intensity	R=900 lm, G=1620 lm, B=360 lm, W=1800 lm (mains supply)
Operating Modes	DMX, Auto, Master/Slave
Dimming	Electronic 0-100%
Built-in Programs	10 automatic programs
Strobe Function	Adjustable speed via DMX or menu
Safety	Grounded circuit required; IP65 housing; avoid direct eye exposure; operating temperature ≤40°C
Maintenance	Clean optics with lens tissue and alcohol at least twice a month; power off and cool before cleaning
Fuse Replacement	Only by qualified personnel; disconnect power first
Warranty / Compliance	CE certified per EN 60598, EN 55015, EN 61547, EN 61000

Frequently Asked Questions - WH128 150.567 BeamZ

How do I set the DMX address on the BeamZ WH128?

Press MENU and scroll to Addr. Press ENTER, then use UP/DOWN to set the desired address (1-512). Press ENTER to confirm.

What are the available DMX channel modes?

The fixture supports 1-channel (color selection), 4-channel (individual RGBW control), and 8-channel (dimmer, RGBW, strobe, auto programs, speed). Select via Chnd in the menu.

How do I clean the unit?

Disconnect power and allow the fixture to cool. Use a lens tissue or soft cotton cloth with alcohol to gently wipe the optics. Clean at least twice a month to prevent overheating.

What is the password function (Pasd) used for?

The Pasd menu allows you to set a password to restrict access to certain functions. Enable it by entering a password in the Pasd menu.

How do I use the fixture in master/slave mode?

Set one unit as master (in auto or sound mode) and others as slave by selecting Slav in the menu. Connect all units via DMX cable. The slaves will follow the master's program.

What is the maximum ambient temperature for safe operation?

The ambient temperature should not exceed 40°C (104°F) to avoid overheating and damage.

Can I replace the LEDs or fuse myself?

Only qualified personnel should replace the light source or fuse. Always disconnect power before any replacement.

How do I select an auto program?

Press MENU and scroll to Auto. Press ENTER, then choose between Auto 1, Auto 2, or Auto 3 (or up to 9 in 8-channel mode). Press ENTER to confirm.

What does the IP65 rating mean?

IP65 means the fixture is dust-tight and protected against water jets. Suitable for outdoor use but not submersion.

How do I reset the fixture to factory settings?

The manual does not specify a factory reset. You can manually set each parameter to default via the menu: DMX address to 1, channel mode to 1CH, etc.

USER MANUAL WH128 150.567 BeamZ

MANUAL

Thank you for purchasing our company products.

Please read these instructions carefully to enjoy optimum performance and a longer service life before you start to use.

CONTENTS

Unpacking Inspections....2

Unpacking instructions 2

Safety Instructions 2

Functions Introductions....3

Main Functions....3

System menu....4

Operating instructions....6

DMX channels 6

Maintenance 7

Specification 7

UNPACKING INSPECTIONS

Unpacking instructions

• Please unpack the carton and check the goods carefully when you receive it, if discover packing damage, shortage or quality problem, please notify the shipper and reject the goods.
• Before using this product, please read the instructions carefully and keep it in a safe place for future reference.

SAFETY INSTRUCTIONS

• Safety and regulatory power socket with high quality output should be used.
  • Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Never put tiny metal objects such as a screwdriver, iron wire and coins, etc. into the internal or stretch into the machine in case of short circuit.
• Please make sure to connect the proper voltage and do not higher or lower than that stated on the decal or rear panel of the product.
• Avoid hitting, crashing or squeezing with other objects in transportation. Never carry the product from the power cord or any moving part. Always use the hanging / mounting bracket or the handles.
• Never pull or tug on the cord and change it for another one, stop using it when it is damaged or becomes hot.
• Stop using the product once there is sparks when connecting with the power plug.

• Make sure there are no flammable materials close to the fixture while operating. Always install it in a location with adequate ventilation.

• Never replace the lighting source with different specification and rating when the original one is damaged.
  • Make sure to power off before replacing the light source or the fuse. Never do it while it is on.

• The ambient temperature is no more than 40°C(104°F) .
• Never clean the fixture by water, thinner or other dissolved agent.
• Stop using the product in case of a serious operating problem and send it to our maintenance agent immediately. Never repair by non-professional workers.
• Avoid direct eye exposure to the light source while the product is on.

SPECIFICATION

Light intensity	Lms: R=900, G=1620, B=360, W=1800 with mains supply
No. of LEDs 12x 8W Quad LEDs
DMX channels	1-4-8
IP Rating IP65
Power Supply	220-240Vac / 50Hz
Consumption	115W
Dimensions 39	8 x 220 x 289mm
Weight	17.5kg

MAINTENANCE

The unit should be cleaned periodically to ensure the optimum performance, the smudginess can decrease the life of light and the output of light is affected by the dust which can make the machine overheating. In general, make the maintenance at least two times a month. Be sure to power off the unit before cleaning.

Do not clean until the unit recovers normal temperature since high temperature for using, use the lens tissue or soft cotton cloth with alcohol to wipe gently.

Cleaning frequency depends on the environment in which the fixture operates, damp, smoky or dirty surrounding can cause greater accumulation of dirt on the optics. Never rub or press strongly on the panel.

FUNCTIONS INTRODUCTIONS

Main Functions

• 1, 4 or 8 DMX channels.
- DMX, auto and master/slave mode.
• 12x 8W Quad LEDs
• 10 Built-in programs
• Electronic dimming 0 – 100%

System menu

Stat - Set the static color mode and strobe mode

Press MENU, press the UP or DOWN button until "Stat" is displayed, press ENTER.

You have now 5 options. To select the desired option press ENTER. With the UP and DOWN button the desired value can be set. Press ENTER to confirm the desired value.

Colo - Built-in color mix

Press MENU, press the UP or DOWN button until "Colo" is displayed, press ENTER.

"Colx" will now be displayed, ("x" representing a number between 0 - 51). Press the UP or DOWN button to find the desired static mode. Press ENTER to confirm

Auto mode – This menu will let you select the desired auto mode.

Press MENU, press the UP or DOWN button until "Auto" is displayed, press ENTER.

There are 3 auto modes, press the UP or DOWN button to select the desired mode, press ENTER to confirm.

Channel mode – Select the desired channel mode

Press MENU, press the UP or DOWN button until "Chnd" is displayed, press ENTER

“X Ch” will now be displayed, (“X” represents the displayed channel mode). Press the UP or DOWN button to find the desired channel mode. Press ENTER to confirm.

DMX Address – Set the DMX address

Press MENU, press the UP or DOWN button until "Addr" is displayed, press ENTER.

"Axxx" will now be displayed, ("xxx" represents the displayed address). Press the UP or DOWN button to find the desired address. Press ENTER to confirm

Pasd – Password function switch.

Press MENU, press the UP or DOWN button until "Pasd" is displayed, press ENTER.

Set the password for the password function.

Info – Will display the software version and working time of the unit.

Press MENU, press the UP or DOWN button until "Info" is displayed, press ENTER.

The software version of the unit will be displayed. Press MENU to leave this function

Slave mode – In this mode the unit functions as a slave

Press MENU, press the UP or DOWN button until "Slav" is displayed, press ENTER.

"Sla" will now be displayed, Slave mode is confirmed. The unit will now act as a slave in Auto, sound and chase mode.

OPERATING INSTRUCTIONS

DMX connection.

Master / Slave connection.

DMX CHANNELS:

1 DMX Channel mode:

Channel	Value	Function
1	0	Light off
	1-4	Color 1
	5-9	Color 2
	10-14	Color 3
	....	....
	240-244	Color 48
	245-249	Color 49
	250-254	Color 50
	255	Color 51

4 DMX Channel mode:

Channel	Value	Function
1	0-255	Red
2	0-255	Green
3	0-255	Blue
4	0-255	White

8 DMX Channel mode:

Channel	Value	Function
1	0-255	Dimmer
2	0-255	Red
3	0-255	Green
4	0-255	Blue
5	0-255	White
6	0-255	Strobe
7	0	Light off
	1-27	Auto 0
	28-55	Auto 1
	56-83	Auto 2
	84-111	Auto 3
	112-139	Auto 4
	140-167	Auto 5
	168-195	Auto 6
	196-223	Auto 7
	224-251	Auto 8
	252-255	Auto 9
8	0-255	Speed (slow-fast)

tronios

Sound & Light

CE Declaration of Conformity

Importer:

TRONIOS

BV

Regulatory Requirement: EN 60598-1/-2-17

EN 55015

EN 61547

EN 61000-3-2/-3-3

The product meets the requirements stated in the above mentioned Standards.

13-12-2012

Signature :

Specifications and design are subject to change without prior notice..

www.tronios.com

Copyright © 2013 by TRONIOS the Netherlands