Prospero 152.936 - Machine à effets lumineux BeamZ - Free user manual and instructions

Product Type	Light Effect Machine
Brand	BeamZ
Model	Prospero 152.936
Power Supply	100-240V AC, 50/60Hz
Power Consumption	150W
Light Source	36 x 3W RGBW LEDs
DMX Channels	7 channels
Control Modes	DMX512, Standalone, Sound-Active, Master/Slave
Dimensions (L x W x H)	295 x 230 x 195 mm
Weight	4.2 kg
Housing	Metal and flame-retardant plastic
Cooling	Fan-cooled
Key Features	Static colors, color mixing, strobe effect, dimmer
Safety Certifications	CE, RoHS
Maintenance	Clean with soft dry cloth; avoid moisture
Spare Parts & Repairability	Parts available via authorized BeamZ service centers
Included Accessories	Power cord, user manual, mounting bracket

Frequently Asked Questions - Prospero 152.936 BeamZ

How do I set up the Prospero 152.936 for the first time?

Unpack the fixture, mount it securely using the included bracket, connect the power cord, and turn it on. For DMX control, connect a DMX controller to the DMX IN port and set the desired address.

How many DMX channels does the fixture use?

The Prospero 152.936 operates in 7-channel DMX mode. Refer to the manual for the channel assignment table.

Can I use the fixture without a DMX controller?

Yes, you can use standalone modes: sound-active (built-in microphone), auto mode, or master/slave mode when linking multiple units.

What is the recommended mounting height?

For best performance, mount the fixture at least 2 meters above the floor. Ensure the area around the fixture is clear of flammable materials.

How do I clean the LEDs?

Turn off the fixture and let it cool. Use a soft, lint-free cloth slightly dampened with water or a mild glass cleaner. Do not use abrasive solvents.

Why is the fixture not responding to DMX?

Check that the DMX cable is properly connected and that the controller is set to the correct address. Verify that the fixture is in DMX mode and that the DMX terminator is used if needed.

Can I replace the LEDs?

LEDs are not user-replaceable. If an LED fails, contact an authorized BeamZ service center for repair or replacement.

What is the ambient temperature range for operation?

The fixture is designed for indoor use at ambient temperatures between 0°C and 40°C (32°F to 104°F). Avoid exposing it to extreme heat or moisture.

How do I link multiple fixtures in master/slave mode?

Set the first fixture as master (DMX mode on, but no controller) and others as slave (set them to slave mode). Connect all fixtures with DMX cables. The master will control the slaves.

What spare parts are available?

Common spare parts include the power supply unit, control board, LED modules (complete), and mounting brackets. Contact BeamZ support or an authorized dealer to order.

USER MANUAL Prospero 152.936 BeamZ

Yellow triangular warning sign with black radiating lines and sunburst symbol

CLASS 3B

MANUAL

ENGLISH

Congratulations to the purchase of this Beamz light effect. Please read this manual thoroughly prior to using the unit in order to benefit fully from all features.

Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

• Prior to using the unit, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
• The unit contains voltage carrying parts. Therefore do NOT open the housing.
• Do not place metal objects or pour liquids into the unit This may cause electrical shock and malfunction.
• Do not place the unit near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
• The unit is not suitable for continuous use.
• Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
• When unplugging the unit from a mains outlet, always pull the plug, never the lead.
• Do not plug or unplug the unit with wet hands.
• If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
• If the unit is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the unit on. Contact your dealer. Do NOT connect the unit to a rheostat or dimmer.
• To avoid fire and shock hazard, do not expose the unit to rain and moisture.
• All repairs should be carried out by a qualified technician only.
• Connect the unit to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
• During a thunderstorm or if the unit will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
• If the unit has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the unit in humid rooms or outdoors.

• During operation, the housing becomes very hot. Do not touch it during operation and immediately after.

• To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.

• Secure the unit with an extra safety chain if the unit is ceiling mount. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1 meter space on every side to ensure sufficient cooling.
• This unit contains high intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
• Do not repeatedly switch the fixture on and off. This shortens the life time.
• Keep the unit out of the reach of children. Do not leave the unit unattended.
• Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
• Only operate the unit with clean hands.
• Do not force the controls.
• If the unit has fallen, always have it checked by a qualified technician before you switch the unit on again.
• Do not use chemicals to clean the unit. They damage the varnish. Only clean the unit with a dry cloth.
• Keep away from electronic equipment that may cause interference.
• Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
• Switch the unit off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the unit.
• Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
• The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this unit.
• Keep the original packing material so that you can transport the unit in safe conditions

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.

A DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks should be aware of the effects that this light effect may have on them.

The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.

NEDERLANDS

Features of the product:

1. 150mW blue laser 447nm
2. Scanner system: big angle step motor
3. Working Modes: Sound Active, Auto run, DMX512 (9 CH), Master/slave mode
4. Interface: 3 pins XLR jack for DMX or Maser-Slave linking;
5. Input power: AC 110V\~240V, 50/60Hz. Rated power: 15W.
6. Packing Size: L*W*H=25.5*21.4*18.4CM; Weight: 1.9KG

Front and Rear panel view:

2 3 4 POWER LED MC LED MC 1

5 6 7 8 9 10 POWER SWITCH ON OFF KEY SWITCH SOUND SENSITIVITY MIN MAX INPUT FUNCTION SETTING DISPLAY AC100-240V 50/60Hz OUTPUT ENTER UP DOWN RETURN DMX/Linking

1. Laser Aperture
2. Power LED indicator
3. Mic LED indicator
4. Sound active microphone

5. Power ON/OFF switch

6. Power input socket

7. Laser key safety switch
8. DMX and DMX through jack
9. Sound sensitivity
10. Function setting screen

LED FUNCTION SETTING

LED DISPLAY ENTER UP DOWN RETURN

Press "UP" or "DOWN" to choose functions in the same menu.

Press "ENTER" button to enter next menu.

Press "RETURN" button to return previous menu.

When you turn on the laser for the first time, it will take some seconds to auto load the built-in show.

The default setting is AUTO EFFECT 1.

First Menu Second	Second Menu Third Menu Fourth	Menu
AUTO (auto running mode)	RunningEffect 1 (Full show)Effect 2 (only beam)Effect 3 (only cartoon)
SOUD (sound activate mode)	RunningEffect 1 (Full show)Effect 2 (only beam)Effect 3 (only animation)
ADDE	Running in DMX modeA001 (DMX address)
SET (Setting functions)	ADDE Choose DMX address
	L-HT (LCD backlight setting)	ONON 10S (ON for 10 seconds)
	SPED (Running speed)	SP-L (low speed)SP-N (medium speed)SP-H (high speed)
	ASTE (set master unit)	NOYES
	LASE (size and color setting)	S—E (graphic size setting)	S128 (press up or down to choose the size of graphics)
		COLO (laser color setting)(2-4 color option is valid with relative laser diode installed.)	1. Single color2. RGY3. RGB4. RGP
	DEFA(Restore default setting)	YesNo
TEST	TES1 (test pic with square)TES2 (test pic with tunnel)

Universal DMX Operation (DMX mode)

This mode allows you to use universal DMX-512 console to operate.

1. Install the units in a suitable position.
2. Use standard XLR cable to connect your units together via the XLR connector on the rear of the units. For longer cable we suggest a terminator at the last fixture.
3. Assign a DMX address to each the unit using dipswitches.
4. Turn on all units. Use DMX console to control your units.

POWER SWITCH ON OFF KEY SWITCH ON OFF SOUND SENSITIVITY MIN MAX CE FUNCTION SETTING DISPLAY OUTPUT AC100-240V 50/60Hz DMVLIHING POWER SWITCH ON OFF KEY SWITCH ON OFF SOUND SENSITIVITY MIN MAX CE FUNCTION SETTING DISPLAY OUTPUT AC100-240V 50/60Hz DMVLIHING

DMX Signal

Instruction for DMX channels

CH1	LASER OFF	0~41 LASER OFF
	Auto Activate	42~83 DMX mode, CH2~CH12 valid
		84~125 Build-in cartoon graphics auto running mode
		126~167 Build-in beam graphics auto running mode
	Sound Activate	168~209 Build-in beam graphics auto running mode
		210~251 Build-in cartoon graphics auto running mode
		252~255 DMX mode, CH2~CH12 valid
CH2	Pattern select	0~255 Selecting built-in patterns
CH3	Rotation	0~127 Manual rotation
		128~191 Auto counter-clockwise rotation (from slow to fast)
		192~255 Auto clockwise rotation (from slow to fast)
CH4	X axis rolling	0~127 Manual rolling
		128~255 Auto rolling (from slow to fast)
CH5	Y axis rolling	0~127 Manual rolling
		128~255 Auto rolling (from slow to fast)
CH6	X axis moving	0~127 Manual choose moving position
		128~255 Auto moving (from slow to fast)
CH7	Y axis moving	0~127 Manual choose moving position
		128~255 Auto moving (from slow to fast)
CH8	Pattern size	0~63 Choose pattern size, 0 is normal size, 1 is the smallest, 63 is the biggest
	Zooming	64~127 Auto zooming (-) from slow to fast
		128~191 Auto zooming (+) from slow to fast
		192~255 Manual zooming (+/-) from slow to fast

TROUBLE SHOOTING

1. If the power indicator is off and the laser doesn't work, please check the power supply and the input.
2. In Stand-Alone operation, if the power supply indicator is ON and sound active indicator is OFF, but the laser doesn't work.

A. Because sound is too small and cannot activate laser running, please increase the music volume or increase audio sensitivity on rear panel.

B. Please check if unit has been set up in slave mode, or DMX mode.

1. In Master-Slave operation, slave units don't function, please check as below.

A. Make sure there's only one master in the chain, and the others are set in slave mode.
B. Make sure to control the units with DMX controller.
C. Make sure to use a good quality power cable and XLR connector.

1. In DMX operation, the unit can't be controlled by the DMX console, but the DMX signal indicator is flashing, please make sure the DMX console and unit have the same channel.

2. If the output beam direction above is unusual, please restart the unit.

3. If the unit is fail, please turn off the unit, and then turn on again after 5 minutes.

After trying the above solution you still cannot sort out the problem, please contact your dealer or our company for service

Blue glossy circular button with a stylized white 't' logo (no text or symbols)

tronios

Sound & Light

CE Declaration of Conformity

Importer: 7777777TRONIOS BV

Regulatory Requirement: EN 60598-1/-2-17

EN 55015

EN 61547

EN 61000-3-2/-3-3

The product meets the requirements stated in the above mentioned Standards.

7

22-07-2013 777777

77

Signature :

Handwritten signature or scribble on white background, possibly a signature or artistic mark