WAB-7000 - Access Point LEVELONE - Free user manual and instructions
Find the device manual for free WAB-7000 LEVELONE in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Wireless Access Point |
| Wireless Standard | IEEE 802.11a/b/g/n |
| Frequency Band | 2.4 GHz and 5 GHz |
| Max Data Rate | 300 Mbps (2.4 GHz) + 300 Mbps (5 GHz) |
| Ports | 1 x 10/100/1000 Ethernet (PoE 802.3af) |
| Power Supply | Power over Ethernet (PoE) or DC 12V adapter |
| Dimensions (W x D x H) | 160 x 120 x 30 mm |
| Weight | 300 g |
| Mounting | Wall/ceiling mountable |
| Antenna | 2 internal antennas |
| Security | WEP, WPA/WPA2, MAC address filtering, hidden SSID |
| Management | Web-based GUI, SNMP, DHCP client |
| Operating Temperature | 0°C to 40°C |
| Humidity | 10% to 90% non-condensing |
| LED Indicators | Power, LAN, Wireless |
Frequently Asked Questions - WAB-7000 LEVELONE
What is the default IP address of the WAB-7000?
The default IP address is 192.168.1.1. If it doesn't work, try 192.168.0.1 or check your DHCP server.
How do I reset the WAB-7000 to factory defaults?
Press and hold the reset button on the back of the device for about 10 seconds until the LEDs blink. The device will reboot with factory settings.
Does the WAB-7000 support PoE?
Yes, it supports IEEE 802.3af Power over Ethernet. You can power it via a PoE switch or a PoE injector.
How can I improve the wireless range of the WAB-7000?
Place the access point centrally, away from obstacles and interference sources. Adjust antennas if external are available. Also, try changing channels to avoid congestion.
What security modes are available on the WAB-7000?
The device supports WEP (64/128-bit), WPA-PSK, WPA2-PSK, and WPA-Enterprise with RADIUS server. It also offers MAC address filtering and disabling SSID broadcast.
How do I update the firmware on the WAB-7000?
Download the latest firmware from the LevelOne website. Log into the web interface, go to ‘System Tools’ -> ‘Firmware Upgrade’, and upload the file. Do not power off during upgrade.
Can I use the WAB-7000 as a wireless bridge?
Yes, the WAB-7000 supports bridge (WDS) mode. You need to configure both access points with the same channel and wireless settings. Check the manual for WDS setup.
Why is my WAB-7000 not connecting to the network?
First, check the Ethernet cable and PoE power. Ensure the device is in the correct mode (Access Point, not Router). Verify IP address settings and try a reboot.
What is the maximum number of clients supported by the WAB-7000?
The recommended maximum is about 30-40 simultaneous wireless clients for stable performance. Actual capacity depends on network traffic and environment.
How do I configure VLANs on the WAB-7000?
The WAB-7000 supports 802.1Q VLAN tagging. In the web interface, go to ‘Network’ -> ‘VLAN’ and assign VLAN IDs to SSIDs or the management interface.
User questions about WAB-7000 LEVELONE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Point in PDF format for free! Find your manual WAB-7000 - LEVELONE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. WAB-7000 by LEVELONE.