MorMics MX310 - Blender ROLLS - Free user manual and instructions

Product Type	Blender
Brand	Rolls
Model	MorMics MX310
Dimensions (H x W x D)	Approx. 400 x 200 x 200 mm
Weight	Approx. 2.5 kg
Power Rating	600 W
Power Supply	220-240 V, 50/60 Hz
Jug Capacity	1.5 L
Blade Material	Stainless steel
Housing Material	BPA-free plastic
Functions	Blending, ice crushing, pulse
Speed Settings	2 speeds + pulse
Cord Length	1 m
Cleaning	Removable jug and lid are dishwasher safe
Safety Features	Overheat protection, non-slip feet
Spare Parts Available	Replacement jug, blade assembly, lid
Repairability	Repairable by qualified technician; spare parts sold separately
Maintenance	Clean after each use; descale monthly
Warranty	2 years
Certifications	CE, RoHS

Frequently Asked Questions - MorMics MX310 ROLLS

How do I clean the blender jar?

Remove the jar from the base and rinse immediately after use. For thorough cleaning, wash with warm soapy water or place the jar and lid on the top rack of your dishwasher. Do not immerse the motor base in water.

Can I blend hot liquids in this blender?

No, blending hot liquids can cause pressure buildup and lead to the lid blowing off. Always allow liquids to cool to room temperature before blending.

What should I do if the blender stops working?

First, check that the unit is plugged in and the power outlet is working. If the motor stops during use, it may have triggered overheat protection. Unplug and let it cool for 15 minutes before restarting.

Is the blender suitable for ice crushing?

Yes, the MorMics MX310 is designed to crush ice. Use the pulse function to break ice into desired consistency. Add a small amount of water to aid the process.

Can I use the blender to grind dry spices?

This blender is not recommended for grinding dry spices as it may damage the blades. For dry grinding, consider a dedicated spice grinder.

How do I replace the blade assembly?

Unscrew the blade assembly from the base of the jar. Replace with a genuine Rolls replacement part. Ensure the rubber seal is properly positioned to prevent leaks.

What is the maximum capacity for blending?

Do not fill the jar beyond the maximum fill line (1.5L). Overfilling can cause leaks and motor strain. For thick mixtures, reduce the quantity.

Why does the blender have a strong smell when new?

A slight motor smell is normal during the first few uses as the internal components break in. If the smell persists or becomes acrid, stop use and contact support.

Can I blend fibrous vegetables like celery?

Yes, but cut them into small pieces (2-3 cm) and add enough liquid. Fibrous ingredients may get stuck; use the pulse function to free them.

Is the blender jar BPA-free?

Yes, the jar is made from BPA-free plastic, safe for food and beverages. Avoid using abrasive cleaners to maintain clarity.

USER MANUAL MorMics MX310 ROLLS

• Mixes three microphones to one XLR output
• Output level controls and a mic/line-level output switch
• Phantom Power and Low-Cut switches for each Mic input

The MX310 is a very useful microphone mixer. It's perfect for sub-mixing microphones in an installation or recording application. The Phantom Power and Low-Cut switches add to the versatility and usefulness of the MX310.

ROLLS

Rolls Corporation Salt Lake City, UT 12/12

ROLLS

MX310

3-Channel mono Mic Mixer

SPECIFICATIONS

Input Impedance: 600 Ohms

Output Impedance: 600 Ohms Mic - 200 Ohms line

THD + Noise: .05% Typical

Frequency Response: 20 Hz - 20 kHz (+0 / -3 dB)

Voltage Gain: 50 dB line/10 dB Mic

Low Cut: -3 dB @ 100 Hz

Current Draw: 20 mA

Phantom Power: +12 VDC

Connectors: 3 Female XLR, 1 Male XLR, 1 1/8" TRS,

DC

Power

Jack

Maximum Supply Voltage: 16 VDC

Size: 5.25" x 3.75" x 1.5"

Weight:

1

lbs.

Quick Start Guide

INTRODUCTION

Thank you for your purchase of the MX310. This unit is designed and manufactured to mix three microphones together and send their combined signals out to a single transformer-balanced XLR output. The individually switchable phantom power and low-cut switches provide the final touches which make the MX310 a valuable tool for any sound reinforcement, musical, recording, or install application.

INSPECTION

1. Unpack and Inspect the MX310 package.

Your MX310 was carefully packed at the factory in a protective carton. Nonetheless, be sure to examine the unit and the carton for any signs of damage that may have occurred during shipping. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future.

1. For warranty registration go to our website: WWW.ROLLS.COM

DESCRIPTION

REAR PANEL

Mic Input: 1 - 3: XLR balanced inputs for connection to any standard dynamic or condenser microphone.

Output: Transformer balanced XLR output jack for connection to the next device in the signal chain such as a mixer, signal processor or amplifier. MIC/LINE Switch: This switch adjusts the output XLR level from Mic or Line level. This switch does not effect the Aux/Headphone Output.

FRONT PANEL

Mic Level 1 - 3: These controls adjust the level of the corresponding Mic channel. The level varies from -infi nity (off) to +60 dB of gain (typical). Phone/Aux: 1/8" TS (tip,sleve AKA mono) jack which may be connected to a pair of mono headphones (if you use stereo headphones you will only hear the left side) for personal monitoring, or to an unbalanced input of a signal processor or amplifi er.

Power LED: Indicates the MX310 is on.

Clip LED: Indicates that clipping is about to occur or occurring in the MX310 circuitry. This LED begins to light 3dB below actual circuit clipping.

Located on the right side of the unit is the +12 VDC power jack for connection to the Rolls PS27 +12 VDC (outside of the ring is positive) external power supply.

On the left side are the Phantom Power and Low-Cut switches. As shown here, under each number is a P indicating Phantom Power, and an L which indicates Low-Cut.

When the P switch is DOWN, the phantom power is ON, when it is UP, the phantom power is OFF. When the L switch is UP, the low-cut is ON, when it is DOWN, the low-cut is OFF.

SCHEMATIC