Q: Does the Zyxel NWA1100 support the mesh protocol?

No, the Zyxel NWA1100 does not support the mesh protocol. This access point operates in standard access point mode (AP mode) and does not have network mesh capabilities. The NWA1100 is designed to function as a standalone access point connected to your network via its 10/100 Mbps Ethernet port. It communicates according to the IEEE 802.11b/g standards in the 2.4 GHz band with a maximum throughput of 54 Mbps. If you want a mesh system, you will need to choose another Zyxel product specifically designed for this type of configuration, where multiple devices can relay the wireless signal to extend coverage.

Q: How to reset a ZYXEL NWA-1100 wireless access point to factory settings?

To reset your ZYXEL NWA-1100 wireless access point to factory settings, you have two methods: using the physical button or via the web interface. Method 1: Using the physical RESET button This method is the most reliable, especially if you have forgotten your password or cannot access the web interface. The RESET button is located at the back of the NWA-1100 (on the rear panel). Follow these steps: Locate the small RESET button at the back of the device. Press and hold this button for about 10 seconds . You will see the device's LED indicators flash, indicating that the reset is in progress. Release the button once you see the LEDs flashing. The device will automatically restart with its factory settings restored. Method 2: Via the web interface If you have access to the NWA-1100's web interface, you can also restore the factory settings directly in the Maintenance or Administration section (section 14.7 of the user manual). After the reset Once the reset is complete, all custom settings have been erased. The default administrator password returns to 1234 and the IP address reverts to its factory value. You will need to completely reconfigure your access point: Wi-Fi settings, password, SSID, channel, WPA2 security, and other network options according to your needs.

Question 1

Does the Zyxel NWA1100 support the mesh protocol?

Accepted Answer

No, the Zyxel NWA1100 does not support the mesh protocol. This access point operates in standard access point mode (AP mode) and does not have network mesh capabilities.

The NWA1100 is designed to function as a standalone access point connected to your network via its 10/100 Mbps Ethernet port. It communicates according to the IEEE 802.11b/g standards in the 2.4 GHz band with a maximum throughput of 54 Mbps.

If you want a mesh system, you will need to choose another Zyxel product specifically designed for this type of configuration, where multiple devices can relay the wireless signal to extend coverage.

Question 2

Can two Ethernet WAN connections be configured on the ZYXEL ZYWALL USG 100?

Accepted Answer

Yes, the ZYXEL ZYWALL USG 100 has two dedicated Ethernet WAN ports allowing you to configure two separate Internet connections in parallel on ports P1 and P2.

By default, these two WAN ports are configured as DHCP clients and operate independently to accommodate two Internet lines from different Internet Service Providers (ISPs). You can use them to:

Connect two Internet links from distinct providers for redundancy
Set up automatic failover: if the first line goes down, traffic automatically switches to the second
Configure load balancing to distribute traffic between the two connections

Practical setup: Use Category 5e (or higher) 8-wire Ethernet cables to connect each WAN port to your Internet connection equipment (modems, routers). The firewall installation wizard offers an option “INSTALLATION CONFIGURATION, TWO ISPs” that guides you step by step through the setup of each WAN connection. After connecting the cables, access the firewall's web interface (192.168.1.1) and launch this wizard to enter the specific settings for your two ISPs (encapsulation type, DNS, etc.).

By default, no further configuration is necessary: the ZYWALL USG 100 automatically recognizes the two WAN ports and activates them as soon as they receive an IP address via DHCP.

Question 3

How to reset a ZYXEL NWA-1100 wireless access point to factory settings?

Accepted Answer

To reset your ZYXEL NWA-1100 wireless access point to factory settings, you have two methods: using the physical button or via the web interface.

Method 1: Using the physical RESET button

This method is the most reliable, especially if you have forgotten your password or cannot access the web interface. The RESET button is located at the back of the NWA-1100 (on the rear panel). Follow these steps:

Locate the small RESET button at the back of the device.
Press and hold this button for about 10 seconds.
You will see the device's LED indicators flash, indicating that the reset is in progress.
Release the button once you see the LEDs flashing.
The device will automatically restart with its factory settings restored.

Method 2: Via the web interface

If you have access to the NWA-1100's web interface, you can also restore the factory settings directly in the Maintenance or Administration section (section 14.7 of the user manual).

After the reset

Once the reset is complete, all custom settings have been erased. The default administrator password returns to 1234 and the IP address reverts to its factory value. You will need to completely reconfigure your access point: Wi-Fi settings, password, SSID, channel, WPA2 security, and other network options according to your needs.

Question 4

Does the Zyxel XGS-4528F switch offer user accounts other than the default administrator account?

Accepted Answer

Yes, the Zyxel XGS-4528F switch offers several user accounts in addition to the default administrator account. The system supports up to five simultaneous accesses via the web interface: one administrator account (admin) and up to four additional user accounts.

The two types of available accounts are:

Administrator account (admin): Full read and write access. You can modify all the switch settings. The default password is 1234 (it is strongly recommended to change it).
Non-administrator accounts (up to 4 others): Read-only access by default. These accounts can view configurations and statistics without being able to modify them via the web interface.

To manage user accounts: Log in to the XGS-4528F switch via its web interface (http://192.168.1.1 by default), then navigate to Management > Access Control > Logins. In this screen, you can create new accounts, modify existing passwords, and manage authentication settings. Each account can have a unique username (up to 32 characters) and a personal password.

For users who need additional administrator rights in CLI commands (privilege levels from 0 to 14), you can configure these permissions via the command line, or use external RADIUS or TACACS+ authentication for centralized access and rights management across multiple devices.

User manual ZYXEL : user manuals and guides in PDF

Models ZYXEL most viewed

Browse manuals ZYXEL by appliance type

Recent questions about devices ZYXEL