HB232ABR0J - Plaque de cuisson SIEMENS - Notice d'utilisation et mode d'emploi gratuit

Caractéristiques techniques	Four encastrable multifonction, classe énergétique A, capacité de 71 litres, 8 modes de cuisson.
Dimensions	Dimensions (H x L x P) : 59,5 cm x 59,4 cm x 54,8 cm.
Poids	Poids : 36 kg.
Utilisation	Commandes électroniques avec affichage numérique, minuterie intégrée, éclairage intérieur.
Maintenance	Nettoyage par catalyse, possibilité de nettoyage à la vapeur.
Sécurité	Verrouillage de sécurité, porte froide, protection contre la surchauffe.
Informations générales	Garantie de 2 ans, compatible avec les cuisines modernes, design élégant en inox.

FOIRE AUX QUESTIONS - HB232ABR0J SIEMENS

Comment allumer le four SIEMENS HB232ABR0J ?

Pour allumer le four, tournez le bouton de sélection des fonctions sur la position souhaitée et réglez la température. Le four s'allumera automatiquement.

Comment régler la température sur le SIEMENS HB232ABR0J ?

Utilisez le bouton de réglage de la température pour ajuster la température souhaitée. Les valeurs sont affichées sur l'écran de contrôle.

Comment nettoyer l'intérieur du four ?

Pour nettoyer l'intérieur, utilisez un chiffon humide avec un nettoyant doux. Évitez les produits abrasifs qui pourraient rayer la surface.

Le four ne chauffe pas, que faire ?

Vérifiez si le four est bien branché et si le disjoncteur n'est pas déclenché. Si le problème persiste, contactez le service client.

Comment utiliser la fonction de nettoyage à la vapeur ?

Ajoutez de l'eau dans le bac prévu à cet effet, sélectionnez la fonction de nettoyage à la vapeur et lancez le programme. Suivez les instructions affichées.

Comment programmer une cuisson différée ?

Sélectionnez la fonction de cuisson, réglez la température et le temps de cuisson, puis appuyez sur le bouton de programmation pour définir le début de la cuisson.

Que faire si l'écran du four est éteint ?

Vérifiez si le four est branché et que l'alimentation est fonctionnelle. Si l'écran reste éteint, contactez le service après-vente.

Comment changer l'ampoule du four ?

Débranchez le four, retirez le couvercle de l'ampoule et remplacez l'ampoule par une neuve. Rebranchez le four une fois la réparation effectuée.

Le four fait un bruit étrange, que faire ?

Un bruit léger est normal pendant le fonctionnement. Si le bruit est fort ou inhabituel, débranchez le four et contactez le service technique.

Comment obtenir de l'aide technique pour le SIEMENS HB232ABR0J ?

Vous pouvez contacter le service client de SIEMENS via leur site web ou par téléphone pour toute assistance technique.

MODE D'EMPLOI HB232ABR0J SIEMENS

jE jL bJ 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1

j=glg，jgi= gPE jj：

（）

jiue guan liang

1Jg j=0a,① PE 2j/2j:1j

（j）j

5 1 -0

a

1

2

1 1

a

J

1

.iiS jI r.o.iS Jg sla.2

3

fa

1 2

gla 15d

j 1

iolj

1

3j j Jlail j 00000000000000000000000000000000000000

15

a b c d e f g h i j k l m n o p q r s t

1

10 90 10

70

i 1

.2j j j j j j j j j

S 1000000000000000000000000000000000000000000

y jkll cai b 1 y lac g 00j y j k 1 j j j j j

15

1

.

g j 1j 1j y A oj j r j 000000000000000000000000000

1. 23

s s B j 1 o

i

2Jc- ciui 4a j0

J 1

Saaasaaaasaaasaaasaa

aai jai gl aia aai glaaalr gai bla 1 r

3J-oluiu cuiL Jolai

1

a a 1

aJg jLjw JnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJnJn

4.4-4.5g

C Aalal 1

J 1

（）

J 1

Jus Juaio

000000000000000000000000000000000000000000

i 1

41 1 3

（）

aaiia aaii j i ciia 3

1000 1000

aaiai aaii jui ciiaai jy jj

g j 1 g 1 g 1 g 1 g 1 g 1 g 1 g 1 g 1 g 1 g 1 g 1 g

j j 4 j j 4 d

0

Jus Juaa Cui

1 1

jbi jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy jy

S ACD = S COD + S_ DCE

j 4 j 4

iJ 1j0j j00

y 1

aai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai jai

Jusu Jusu Jusu Jusu Jusu Jusu Jusu Jusu

iuiu ouiu uuiu juaaui

en

Important information - Fig. 1

The = safe operation of this appliance can only be guaranteed conductor). has been installed to a professional standard in accordance with these installation instructions. = The installer shall be liable for any damage resulting from incorrect installation. Please not PE conductor
- Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transit.
- Proceed in accordance with the installation sheets for installing accessories.
Before starting up the appliance, remove any packaging material and adhesive film from the cooking compartment and the door.
Fitted units must be heat-resistant up to 90 = ^ and adjacent unit fronts up to 70 = ^
Do not install the appliance behind a decorative door or the door of a kitchen unit, as this may cause the appliance to overheat.
■ Any cut-outs that need to be made in the units should be made before=the=appliance=is=installed.=Remove=any=shavings,as=they may prevent the electrical components from working properly. Removal
Wear = protective gloves so that you do not cut yourself. Parts that Disconnect the appliance from the power supply.
are accessible during installation may have sharp edges. 2. Undo the securing screws.
The=mais=ssket=for=the=appliance=must=either=be=located=in theLift the appliance slightly and then pull it out completely. hatched area A or outside of the area where the appliance is installed.
Secure=any=unsecured=units=to=the=wall=using=a=standard=bracket
tenductor).
jthc
India only
Please = note = the = different = colour = code = for = the = wiring: = Green/yellow ==
PE conductor (12) , black = neutral conductor, red = live conductor (phase conductor).
If your appliance has a pull-out carriage door, this must be removed beforehand.
1. Slide the appliance all the way in and centre it.
2. Screw the appliance into place.
The gap between the worktop and appliance must not be sealed by additional strips.
Thermal insulation strips must not be fitted to the side panels of the surround unit.
that Disconnect the appliance from the power supply.
2. Undo the securing screws.
3. Lift the appliance slightly and then pull it out completely.
cket

B

The dimensions in the figures are in mm.

Appliance under the worktop - Fig. 2

To ventilate the appliance, the intermediate floor must have a ventilation cut-out.

Secure the worktop to the fitted units.

Proceed in accordance with the installation instructions for the hob.

Appliance in a tall unit - Fig. 3

To ventilate the appliance, the intermediate floors must have a ventilation cut-out.

If the tall unit has another back panel in addition to the element back panels, this must be removed.

Only=fit=the=appliance=up=to=a=height=which=allows=accessories=to=be easily removed.

Corner installation - Fig. 4

To ensure that the appliance door can be opened in a corner installation, take account of dimension C. Dimension D is dependent on the thickness of the unit front under the handle.

Connecting the appliance to the electricity supply

The=appliance=corresponds=to=protection=class=1=and=must=only=be operated with a protective earth connection.

The=fuse=protection=must=correspond=to=the=power=rating=specified on the appliance's rating plate and to local regulations.

The appliance must be disconnected from the power supply whenever installation work is being carried out.

The appliance must only be connected with the power cable provided. Connect the power cable to the back of the appliance (listen for the click).

A 3 m power cable can be obtained from the after-sales service.

The power cable must only be replaced with a cable from the original manufacturer, which can be obtained from the after-sales service.

When the appliance is installed, protection must be provided against accidental contact in the future.

Power cable with a plug with earthing contact

The appliance must only be connected to an earthing contact socket which has been correctly installed.

If the plug can no longer be reached after the installation, a partition must be provided in the phases in the permanent electrical installation in accordance with the installation regulations.

Power cable without a plug with earthing contact

Only allow a licensed professional to connect the appliance. In the permanent electrical installation, a partition must be provided in the phases in accordance with the installation regulations. Identify the phase and neutral conductors in the socket. The appliance may be damaged if it is not connected correctly.

Only connect the hob according to the connection diagram. See the rating plate for the voltage. Connect the wires of the mains power cable according to the colour coding: Green/yellow = PE conductor 12 , blue = neutral conductor, brown = live (external

Securing the appliance - Fig. 5

Removal

4

5

2 3