Q: How to locate a break in the boundary wire of my Yard Force Classic 500B?

Visually inspect the wire Start by checking the entire boundary wire for breaks, knots, or visible damage . Breaks are often easy to spot if the wire has been damaged by a mower, gardening tool, or weather. Check the station connectors Make sure the wire is properly connected to the F (front) and B (back) connectors of the charging station. A poor connection can give the impression of a break. Unplug and firmly reconnect both connectors. Test by sections If you find nothing visually, gradually disconnect the wire in sections to identify where the signal is lost. The S1 and S2 indicators on the station blink when there is a break or no signal - check them at each step to precisely locate the damaged section. Repair the break Once the break is located, your manual contains provided repair connectors . You can repair the broken wire with these connectors or completely replace the damaged section.

Question 1

How to install the boundary wire on the Yard Force Classic 500B?

Accepted Answer

To install the boundary wire on your Yard Force Classic 500B, start by preparing your lawn by mowing it to a height of 60 mm or less. Burying the wire is optional, but the closer it is to the ground, the less likely it is to be damaged during mowing.

Use the ruler provided in the kit to maintain a minimum distance of 30 cm between the wire and all obstacles (walls, trees, fences, garden furniture, etc.). First, place the stakes on the lawn to check their positioning before driving them in. The recommended spacing is about 80 cm between two stakes in a straight line, and less in tight turns. Important: the hook of the stakes and the groove of the wire must always face outward from the marked area. Lightly drive the stakes in with a light hammer until you are sure of their correct positioning.

Position the charging station on flat and even ground, in the shade if possible. Leave at least 1.5 m of straight wire in front of the station and 30 cm on the side facing the mowing area. Place the charging station at the end of the wire so that it passes under the center of the station (approximate distance of 10 to 15 mm). Connect one end of the wire to the connector F (front) - black connector on the left, then the other end to the connector B (rear) - red connector on the right.

Before fully driving in the stakes, test the operation: plug the station into a power outlet and check that the blue LED indicator confirms a good installation. Place the robot a few meters from the station, turn the power button ON and press the unlock button 4 times. The robot should automatically return to the station by following the wire. If the device returns and charges correctly, it means your positioning is adequate. Once the test is successful, then fully drive the fixing stakes into the ground and be careful not to damage the excess wire stored under the station.

Your kit contains 150 stakes and 120 m of wire with 3 repair connectors if needed. The wire voltage is only 32 V, so there is no risk of electrocution. The wire will quickly be covered by grass and become invisible after a few mowings.

Question 2

How to locate a break in the boundary wire of my Yard Force Classic 500B?

Accepted Answer

Visually inspect the wire

Start by checking the entire boundary wire for breaks, knots, or visible damage. Breaks are often easy to spot if the wire has been damaged by a mower, gardening tool, or weather.

Check the station connectors

Make sure the wire is properly connected to the F (front) and B (back) connectors of the charging station. A poor connection can give the impression of a break. Unplug and firmly reconnect both connectors.

Test by sections

If you find nothing visually, gradually disconnect the wire in sections to identify where the signal is lost. The S1 and S2 indicators on the station blink when there is a break or no signal - check them at each step to precisely locate the damaged section.

Repair the break

Once the break is located, your manual contains provided repair connectors. You can repair the broken wire with these connectors or completely replace the damaged section.

Question 3

How to start the Yard Force Classic 500B robotic mower?

Accepted Answer

The Yard Force Classic 500B must be set up with mowing schedules before it can operate. Here is the complete procedure to start it correctly.

Important preparation: The robot must be out of the charging station when setting the schedules.

Step 1 - Initializing the robot: Press and hold the lock button, then switch the power switch to the ON position. Continue to hold the lock button until all the LED indicators light up. This step prepares the robot to receive the settings.

Step 2 - Setting the day of the week: Press the button corresponding to the current day (for example, the first button for Monday). A beep confirms your selection. After 3 seconds, the LEDs will blink, indicating that the day setting is complete.

Step 3 - Setting the time: The time can only be set approximately. The available time slots are: 8:00 AM, 10:00 AM, 12:00 PM, 2:00 PM, 4:00 PM, 6:00 PM, 8:00 PM. Select the time closest to the actual time. You will hear a beep after your selection. For example, if it is 8:25 AM, press the 8:00 AM button; if it is 2:45 PM, press the 2:00 PM button. After 3 seconds, the LEDs will blink, confirming that all settings are complete.

Starting the mowing: Once the schedules are set, press the lock button 4 times in a row to unlock it. Then, press the Start button, and confirm by pressing the OK button. The robot will then start mowing according to the program you have set. The operating time on a full charge is 60 minutes, and charging also takes 60 minutes. The cutting height can be adjusted by turning the adjustment knob on top of the robot (adjustable from 20 mm to 60 mm).

Important note: The rain sensor is enabled by default. If rain is detected, the robot will automatically return to the charging station to protect itself.

Question 4

What does a steady light on indicators S1 and S2 mean?

Accepted Answer

A steady (continuous, non-blinking) light on indicators S1 or S2 means that the peripheral cable signal is in good condition. This indicates that the charging station correctly detects your boundary cable and that everything is functioning normally. It's a great sign.

Complete interpretation of indicators S1 and S2:

Steady light (always on) = Peripheral cable signal OK, normal operation
Single blinking (S1 or S2 blinking alone) = Boundary cable broken, damaged, or disconnected, no signal detected
Alternating blinking (S1 and S2 blinking alternately) = Robot is charging in the station

The Classic 500B uses the S1 signal by default to communicate with the peripheral cable. You should never need to change the signal unless a neighbor has a similar Yard Force with the same signal and creates interference. In this case, you can switch to S2 by pressing the Signal button on the charging station and confirming with the S2 button on the robot's control panel. Important: the signal must be identical on both devices (station AND robot).

If the light remains steady when your robot is functioning normally outside, that's a good sign. It shows that the station is correctly detecting the boundary cable. If you had blinking previously, just check that the cable is not broken, damaged, or poorly connected to the terminals F (front) and B (back) of the charging station.

In case of a single blinking indicator, inspect the entire peripheral cable and connections. If the cable is indeed broken or cut, you can repair it with the provided connectors.

Question 5

Why are the S1 and S2 indicators flashing on my Yard Force Classic 500B?

Accepted Answer

When the S1 and S2 indicators are flashing, it means that the system detects a problem with the boundary wire - it is broken, cut, or disconnected.

Checks to perform:

Inspect the entire boundary wire for cuts, knots, or damage
Ensure that the wire is properly connected to the F (front) and B (back) connectors of the charging station
Make sure that the connections are not loose or corroded
If the wire has a visible break, it must be repaired or replaced

Special case - Alternating flashing:

If you observe an alternating flash (S1 then S2, then S1...), it is normal - the robot is charging on the dock.

Possible interference:

The Classic 500B has two available signals: S1 (fault) and S2. If a neighbor has a similar robot and creates interference, you can switch to the S2 signal. Make sure you are using the same signal on the dock AND the robot panel.

User manual Yard Force Robotic lawn mower : user manuals and guides in PDF

Models Yard Force Robotic lawn mower most viewed

Other categories Yard Force

Recent questions about Robotic lawn mower Yard Force