Q: How to delete alarms on the LA CROSSE TECHNOLOGY WS7018 weather station?

Your LA CROSSE TECHNOLOGY WS7018 weather station has 2 programmable alarms (Alarm 1 and Alarm 2) that you can easily disable or stop according to your needs. To disable a programmed alarm: simply press once on the AL1 button to disable Alarm 1, or on the AL2 button to disable Alarm 2. The corresponding alarm symbol will disappear from the LCD display, indicating that the alarm is now disabled. You can reactivate the alarm by pressing the same button again. To stop a ringing alarm: when the alarm sounds, press any button on the station except the SNZ button. The alarm will stop immediately. If you press the SNZ button instead, you will activate the snooze function, and the alarm will reactivate after the set interval (default 10 minutes). To change an alarm: if you want to change the alarm time instead of simply disabling it, press and hold the AL1 or AL2 button for about 3 seconds until the time starts flashing. Then use the IN (hour) and OUT (minutes) buttons to set the new time, and confirm by pressing AL1 or AL2 again.

Q: What does the OFL error mean on the LA CROSSE TECHNOLOGY WS7018 weather station and how can it be resolved?

The OFL error displayed on your LA CROSSE TECHNOLOGY WS7018 weather station generally indicates that the temperature measured by the outdoor sensor is outside the expected measurement range, often too low (below -40°C or -40°F). Possible causes of the OFL error Extremely low outdoor temperature exceeding the sensor's measurement capability. Weak or defective batteries in the outdoor sensor. Poor connection or incorrect installation of the outdoor sensor. Defective or damaged outdoor sensor. Steps to resolve the OFL error Check the environment: Ensure that the outdoor sensor is not exposed to temperatures below -40°C (-40°F), which exceeds its measurement range. Replace the batteries: Change the batteries of the outdoor sensor with new, high-quality batteries to ensure optimal operation. Check the installation: Verify that the sensor is properly installed, securely mounted, and that the connections are solid. Reset the station: Remove the batteries from the main station and the sensor, wait about 1 minute, then reinsert the batteries first into the main station, then into the sensor. Check the sensor: If the error persists despite all these checks, the outdoor sensor may be defective and require replacement. By following these steps, you should be able to correct the OFL error and regain reliable measurements on your LA CROSSE TECHNOLOGY WS7018 weather station.

Q: What does the error message OF1 on the sensor of the LA CROSSE TECHNOLOGY WS7018 weather station mean and how can it be resolved?

The error message OF1 displayed on the LA CROSSE TECHNOLOGY WS7018 weather station generally indicates a communication or operational problem with the outdoor sensor. Here’s how to identify and resolve this issue: 1. Check the batteries of the outdoor sensor Replace the sensor's batteries with new, high-quality batteries. Ensure that the batteries are correctly inserted with the right polarity. 2. Check the connection and range Make sure the sensor is properly installed and that nothing is obstructing the signal transmission. Ensure that the distance between the outdoor sensor and the main station does not exceed 100 meters in a direct line. Avoid obstacles such as thick walls, electronic devices, or sources of radio interference that could disrupt the link. 3. Reset the station and the sensor Remove the batteries from the main station and the outdoor sensor. Wait about 2 to 3 minutes to allow for a complete reset. First, reinsert the batteries into the main station, then into the outdoor sensor. 4. Check the sensor If the error message persists after these steps, the outdoor sensor may be defective. In this case, it is advisable to contact LA CROSSE TECHNOLOGY customer service to consider repair or replacement.

Question 1

How to delete alarms on the LA CROSSE TECHNOLOGY WS7018 weather station?

Accepted Answer

Your LA CROSSE TECHNOLOGY WS7018 weather station has 2 programmable alarms (Alarm 1 and Alarm 2) that you can easily disable or stop according to your needs.

To disable a programmed alarm: simply press once on the AL1 button to disable Alarm 1, or on the AL2 button to disable Alarm 2. The corresponding alarm symbol will disappear from the LCD display, indicating that the alarm is now disabled. You can reactivate the alarm by pressing the same button again.

To stop a ringing alarm: when the alarm sounds, press any button on the station except the SNZ button. The alarm will stop immediately. If you press the SNZ button instead, you will activate the snooze function, and the alarm will reactivate after the set interval (default 10 minutes).

To change an alarm: if you want to change the alarm time instead of simply disabling it, press and hold the AL1 or AL2 button for about 3 seconds until the time starts flashing. Then use the IN (hour) and OUT (minutes) buttons to set the new time, and confirm by pressing AL1 or AL2 again.

Question 2

What is the role of the TX44DTH-IT sensor for the La Crosse Technology WT280 weather station?

Accepted Answer

The TX44DTH-IT is a wireless external sensor designed to extend the measurement capabilities of your La Crosse Technology WT280 station. It transmits real-time temperature and humidity from the outside to the station, allowing you to have a complete view of the weather conditions both inside and outside your home.

This sensor performs two essential complementary measurements:

Outdoor temperature transmitted directly to the WT280 display, allowing you to visualize the thermal variations of your outdoor environment.
Hygrometry (humidity level) of the outside air, with a detection range of 1 to 99%, useful for assessing climate comfort and planning your activities.

With a range of 100 meters in open space, the TX44DTH-IT communicates with the station via radio signal at a frequency of 868 MHz, without requiring any wiring. This greatly facilitates its installation away from your home, particularly on a facade, balcony, or garden post.

To optimize the sensor's operation, install it sheltered from direct weather by placing it under an eave, awning, or specialized garden shelter, while positioning it in an open area to ensure good radio signal reception. Avoid completely enclosed areas or those buried under too many materials that could block the 868 MHz transmission.

Once paired with your WT280, the TX44DTH-IT provides accurate weather data that enriches your experience of using the station. This outdoor information is particularly useful for making daily decisions: adjusting your clothing, watering your garden at the right time, or adjusting your home's heating based on actual outdoor conditions.

Question 3

How to find the reference of the La Crosse Technology WT280 weather station?

Accepted Answer

The reference of your La Crosse Technology WT280 weather station is usually found on a label located on the device. To locate it, follow these steps:

Turn the station over: Place the station on a flat surface and gently turn it over to access its back.
Look for the label: On the back panel, you should see a label containing several technical details.
Identify the reference: The model reference is clearly indicated, often in the form of "WT280" or a similar code.

This reference is useful for accurately identifying your device, especially for support needs, updates, or purchasing compatible accessories.

Question 4

What should I do if the screen of the LA CROSSE TECHNOLOGY WS7018 weather station is blank despite new batteries?

Accepted Answer

If the screen of your LA CROSSE TECHNOLOGY WS7018 weather station remains black despite installing new batteries, here are several steps to follow to try to resolve this issue:

1. Battery Check

Ensure that the batteries are correctly inserted, respecting the polarity (+ and -).
Remove the batteries, wait a few seconds, then carefully reinsert them.
Try another set of new batteries, as some may be defective despite being new.

2. Device Reset

Remove all batteries and leave the station without power for about 10 minutes to allow for a complete reset.
Then replace the batteries and check if the screen turns on.

3. Physical Inspection

Examine the screen and casing for any visible damage that may prevent display.
Also check that the battery contacts are not corroded or dirty.

4. Operating Conditions

Place the station in a suitable location, away from extreme temperatures and where it can properly receive the necessary signals.

If after these checks the screen still does not turn on, it is possible that the station has a hardware defect requiring specialized technical assistance.

Question 5

Can the LA CROSSE TECHNOLOGY WS7018 weather station display indoor temperature without using the outdoor sensor?

Accepted Answer

Yes, the LA CROSSE TECHNOLOGY WS7018 weather station perfectly displays the indoor temperature without needing the outdoor sensor. The main unit has a built-in temperature and humidity sensor that operates independently of the external wireless transmitter.

What you will see without the outdoor sensor:

Indoor temperature: Real-time display, updated every 15 seconds (range -9.9°C to +59.9°C)
Indoor humidity: Relative humidity percentage (RH%) updated every 20 seconds, with recording of minimum and maximum values
Comfort indicator: A happy or sad smiley symbol indicates whether the conditions are comfortable (20-25.9°C with 45-65% humidity)
Clock and alarms: Full operation of the DCF-77 radio-controlled clock, calendar, and 2 alarms

What you will not see without the outdoor sensor:

Outdoor temperature and humidity
Weather forecasts based on atmospheric pressure
Weather trend indicator (up/down arrow)

The outdoor sensor is completely optional. The WS7018 can operate with 0 to 3 external wireless transmitters (frequency 868 MHz). You can add it later if you wish to monitor the temperature and humidity outside. Simply place the station in an open area, away from direct heat or cold sources, for accurate indoor measurements.

Question 6

What does the OFL error mean on the LA CROSSE TECHNOLOGY WS7018 weather station and how can it be resolved?

Accepted Answer

The OFL error displayed on your LA CROSSE TECHNOLOGY WS7018 weather station generally indicates that the temperature measured by the outdoor sensor is outside the expected measurement range, often too low (below -40°C or -40°F).

Possible causes of the OFL error

Extremely low outdoor temperature exceeding the sensor's measurement capability.
Weak or defective batteries in the outdoor sensor.
Poor connection or incorrect installation of the outdoor sensor.
Defective or damaged outdoor sensor.

Steps to resolve the OFL error

Check the environment: Ensure that the outdoor sensor is not exposed to temperatures below -40°C (-40°F), which exceeds its measurement range.
Replace the batteries: Change the batteries of the outdoor sensor with new, high-quality batteries to ensure optimal operation.
Check the installation: Verify that the sensor is properly installed, securely mounted, and that the connections are solid.
Reset the station: Remove the batteries from the main station and the sensor, wait about 1 minute, then reinsert the batteries first into the main station, then into the sensor.
Check the sensor: If the error persists despite all these checks, the outdoor sensor may be defective and require replacement.

By following these steps, you should be able to correct the OFL error and regain reliable measurements on your LA CROSSE TECHNOLOGY WS7018 weather station.

Question 7

What does the error message OF1 on the sensor of the LA CROSSE TECHNOLOGY WS7018 weather station mean and how can it be resolved?

Accepted Answer

The error message OF1 displayed on the LA CROSSE TECHNOLOGY WS7018 weather station generally indicates a communication or operational problem with the outdoor sensor. Here’s how to identify and resolve this issue:

1. Check the batteries of the outdoor sensor

Replace the sensor's batteries with new, high-quality batteries.
Ensure that the batteries are correctly inserted with the right polarity.

2. Check the connection and range

Make sure the sensor is properly installed and that nothing is obstructing the signal transmission.
Ensure that the distance between the outdoor sensor and the main station does not exceed 100 meters in a direct line.
Avoid obstacles such as thick walls, electronic devices, or sources of radio interference that could disrupt the link.

3. Reset the station and the sensor

Remove the batteries from the main station and the outdoor sensor.
Wait about 2 to 3 minutes to allow for a complete reset.
First, reinsert the batteries into the main station, then into the outdoor sensor.

4. Check the sensor

If the error message persists after these steps, the outdoor sensor may be defective. In this case, it is advisable to contact LA CROSSE TECHNOLOGY customer service to consider repair or replacement.

User manual LA CROSSE TECHNOLOGY Weather station : user manuals and guides in PDF

Models LA CROSSE TECHNOLOGY Weather station most viewed

Other categories LA CROSSE TECHNOLOGY

Recent questions about Weather station LA CROSSE TECHNOLOGY