Question 1

How to adjust the timing on a PFAFF 1070S sewing machine?

Accepted Answer

Adjusting the timing on a PFAFF 1070S sewing machine is a delicate but essential operation to ensure proper sewing. Here are the general steps to follow:

Steps to adjust the timing:

Remove the needle plate: Unscrew and remove the needle plate to access the timing mechanism.
Locate the timing marks: Identify the timing marks on the hook and the needle bar. These marks are used to properly align the parts.
Position the needle: Manually turn the handwheel to place the needle in the highest position.
Check the alignment: The hook should pass just behind the needle at the right moment to catch the thread. If not, an adjustment is necessary.
Loosen the hook screws: Slightly loosen the screws that hold the hook in place so that it can be moved.
Adjust the hook position: Gently move the hook to align the timing marks with the needle. It may be necessary to repeat this step several times for precise adjustment.
Tighten the screws: Once the correct timing is achieved, firmly tighten the hook screws.
Test the machine: Reattach the needle plate and perform several test stitches on a fabric to check that the timing is correct and that the machine operates smoothly.

Tip: If you are not comfortable with this procedure or if the problem persists, it is recommended to consult a qualified professional to avoid damaging the machine.

Question 2

How to clean and maintain a PFAFF 1222 sewing machine?

Accepted Answer

To ensure the proper functioning and longevity of your PFAFF 1222 sewing machine, regular cleaning is essential. Here are the steps to follow for effective maintenance:

Steps to clean your PFAFF 1222 sewing machine

Unplug the machine: Before any operation, make sure the machine is unplugged to avoid any electrical risk.
Remove the presser foot and needle: This makes it easier to access the internal parts to clean.
Clean the sewing area: Use a small soft brush or a paintbrush to remove lint, dust, and debris around the sewing area and in the bobbin case.
Check and clean the bobbin case: Remove it and carefully remove any thread or dirt that could hinder proper functioning.
Lubricate the moving parts: Apply a few drops of special sewing machine oil to the moving parts indicated by the manufacturer to ensure smooth movement.
Wipe the exterior: Use a soft, slightly damp cloth to clean the outer casing. Avoid harsh chemicals that could damage the surface.
Reassemble the machine: Replace the needle and presser foot correctly before turning the machine back on.
Test the machine: Plug it back in and perform a sewing test to ensure everything is working perfectly.

Regular maintenance ensures smooth sewing and prevents breakdowns. Feel free to repeat this cleaning after several hours of use or if you notice any malfunctions.

Question 3

How to raise the feed dogs on the PFAFF 1222E sewing machine?

Accepted Answer

To raise the feed dogs on your PFAFF 1222E sewing machine, follow these simple steps:

Steps to raise the feed dogs

Turn off the machine to ensure your safety during handling.
Locate the feed dog lever: On the PFAFF 1222E model, this lever is usually found at the back or on the side of the machine.
Operate the lever: If the feed dogs are lowered (down position), push or pull the lever to the up position to raise the feed dogs.
Check the movement: Gently turn the machine's handwheel to ensure that the feed dogs move freely and are properly raised.

Raising the feed dogs allows for easier movement of the fabric when you want to position or remove the fabric without it being fed by the machine.

Question 4

How to thread a double needle on a PFAFF 1070S sewing machine?

Accepted Answer

Threading a double needle on your PFAFF 1070S sewing machine is a simple operation that requires following the standard insertion process of the machine, adapted for two parallel needles. Before any handling, make sure that the machine is turned off (position "O") for safety reasons.

Preparation and installation of the needles:

Raise the presser foot to release the tension discs.
Completely loosen the needle clamp screw (located under the arm of the machine).
Insert the double needle (130/705H system compatible with your PFAFF 1070S) into the needle holder, ensuring that the flat side of the shank is facing towards the back of the machine. This positioning is crucial for proper functioning.
Push the double needle all the way into the needle holder, then firmly tighten the needle clamp screw.

Installation of the spools and threading:

Place two spools of thread on the horizontal spool holder (you can use the same color or two different colors depending on the desired effect).
Raise the horizontal spool holder to keep them in place.
Thread the first thread through the upper thread guide (3), then the pre-tension spring guide (4), the tension module, the thread guide of the thread lifter, and finally the horizontal thread guide of the needle holder.
Pass the thread through the eye of the first needle from front to back. Leave about 10 cm of thread at the back and cut it with the integrated thread cutter.
Repeat exactly the same path with the second thread for the second needle. Both threads must follow the same threading path.

Usage and tension:

Check that both threads are properly threaded and untwisted by gently pulling on each of them.
For balanced tension, adjust the tension dial (default setting: "4"). You may need to slightly adjust according to your fabric.
Always do a sewing test on a piece of identical fabric before starting your project.

With a properly threaded double needle, your PFAFF 1070S will create very regular and professional parallel or decorative stitches. Remember to use the appropriate needle plate to avoid damaging the needle.

Question 5

How to correctly thread the thread on a PFAFF 1222 sewing machine?

Accepted Answer

To correctly thread the thread on your PFAFF 1222 sewing machine, first turn on the machine by pressing the power button (C). Make sure the presser foot lever (presser bar lifter) is in the up position (position A), which is essential for this model. Place a standard spool of thread on one of the spool ports at the top of the machine.

Use PFAFF's exclusive "slot-threading" technique: pull the thread from the spool and slide it into the threading slot of the top cover. Guide the thread to the right and down following the arrows engraved on the machine. Pass the thread through the tension disc (between the tension discs located under the cover), then lift it up to the take-up lever above the needle's eye. The thread must pass firmly through the tension to ensure good sewing quality.

Your PFAFF 1222 features a patented automatic needle threader. With the presser foot lever still in position A, lower the needle threader control at the front left by pulling the thread towards you and placing it under the hook. Fully press down the control, which will automatically trap the thread in the needle's eye. Slightly release to allow the hook to come back and pull the thread through. Completely release and free the thread loop.

Preparing the lower thread: open the free arm cover to the left and remove the bobbin case by lifting the latch K. Insert a full bobbin with the thread coming from the top towards you. Pull the thread into the slot of the case and pass it under the spring, ensuring that the bobbin turns clockwise. Reinsert the case by lifting the latch K and pushing until it clicks into place.

Finish by lowering the presser foot lever to position B or C depending on your work. Pull both threads (upper and lower) back under the presser foot to avoid tangling. Do a test on scrap fabric to check that the stitches are even and the tension is balanced. Refer to the tension page in the manual if knots appear on one side only. Only use 130-705-H system needles compatible with your PFAFF 1222.

Question 6

Does the PFAFF 1070S sewing machine require regular lubrication?

Accepted Answer

Yes, the PFAFF 1070S sewing machine requires regular lubrication to ensure its proper functioning and extend its lifespan. Here are the important points to know:

Why lubricate the machine?

Reduce wear on moving parts.
Ensure smooth and quiet operation.
Prevent jams and malfunctions.

Which areas to lubricate?

The bobbin mechanism.
The moving parts around the needle.
The visible gears and shafts.

How to lubricate?

Use a special oil for sewing machines, available at haberdasheries or specialty stores.
Apply a few drops to the identified moving parts.
Run the machine for a few moments to distribute the oil.
Wipe off any excess oil to avoid stains on the fabric.

Lubrication frequency

Lubricate your machine after about 8 to 10 hours of use or as soon as you hear unusual noises. Regular maintenance contributes to the longevity of your PFAFF 1070S.

Question 7

Why do thread loops form under the fabric when sewing with the PFAFF TIPMATIC 1025 machine?

Accepted Answer

When thread loops form under the fabric while using the PFAFF TIPMATIC 1025 sewing machine, it generally indicates a problem with thread tension or installation. Here are the key points to check to resolve this issue:

1. Check the upper thread tension

Make sure the upper thread tension is properly adjusted. Too low tension can cause loops to form under the fabric.
Adjust the tension dial according to the type of fabric and thread used.

2. Check the bobbin

Ensure that the bobbin is correctly inserted into its case, in the right direction.
Make sure the bobbin thread is properly wound and that the bobbin thread tension is appropriate, neither too loose nor too tight.

3. Inspect the needle

Use a needle suitable for the type of fabric and ensure it is properly inserted, straight, and in good condition.
Replace the needle if it is worn or damaged.

4. Additional adjustments

Check that the presser foot is properly installed and suitable for the type of sewing.
Test different sewing stitches and adjust the settings if necessary.

5. Test on a sample

Before sewing your final project, perform a test on a piece of similar fabric to ensure the problem is resolved.

By following these steps, you should be able to eliminate thread loops under the fabric and achieve clean sewing with your PFAFF TIPMATIC 1025 machine.

User manual PFAFF Sewing machine : user manuals and guides in PDF

Models PFAFF Sewing machine most viewed

Other categories PFAFF

Recent questions about Sewing machine PFAFF