Question 1

How to pair the remote control with the LIVARNO IAN 367070.2101 starry sky table lamp?

Accepted Answer

To pair the remote control with your LIVARNO starry sky table lamp model IAN 367070.2101, follow these simple steps:

Steps to pair the remote control

Power the lamp: Make sure the lamp is plugged into a power source and is turned on.
Activate pairing mode on the remote control: Press and hold the pairing button or the power button for about 3 to 5 seconds until a light indicator blinks, indicating that the remote control is ready to connect.
Wait for confirmation from the lamp: The lamp may blink or briefly change brightness to signal that it has detected the remote control.
Test the connection: Use the remote control to turn the lamp on, off, or change the lighting effects to verify that the pairing was successful.

If the pairing does not work on the first try, repeat these steps ensuring that the lamp is turned on and that the remote control is close enough. If problems persist, check that the batteries in the remote control are in good condition.

Question 2

Why is the screen of my LIVARNO IAN 367070.2101 table lamp flickering continuously and making a sound, and how can I resolve this issue?

Accepted Answer

If the screen of your LIVARNO IAN 367070.2101 lamp is flickering continuously and making a sound, it is generally due to the unintentional activation of the setting or alarm mode. Here are the specific causes and solutions for this model:

Flickering and beeping during setting is normal. When you set the time, date, or alarm by pressing the selection button (button 5), the screen flickers and emits a beep sound with each confirmation. This is the standard behavior of this lamp. If you do not intend to adjust these settings, press the Mode button (button 4) to exit the setting mode and return to normal display mode.

Check the alarm status. If the alarm symbol remains active in the function display, press the Mode button (button 4) to switch to alarm mode, then press the arrow buttons (button 6) several times to disable the alarm function. Once disabled, the symbol will disappear and the flickering will stop.

Stop the ringing alarm. If the programmed alarm has gone off at the scheduled time, press any button (buttons 4, 5, or 6) located at the back of the lamp to turn off the sound. Note that if the snooze function is activated, the alarm will ring again after the defined delay (maximum 2 repetitions).

Check the CR2032 backup battery. This lamp contains a CR2032 3 V battery (included and pre-installed) that maintains the settings even when disconnected from the power supply. If this battery is low or faulty, it may cause display malfunctions. To replace it, open the battery compartment at the back by unscrewing the cover with a Phillips screwdriver, remove the old battery, and install a new CR2032 battery, then close the cover.

Perform a complete restart. Unplug the power adapter from the wall outlet for about 1 to 2 minutes. This operation resets the electronic circuit and may resolve temporary malfunctions. Wait for the lamp to fully discharge, then plug the adapter back in. The display should return to a normal state showing the time and temperature.

If after these steps the problem persists, particularly a flickering that does not stop or continuous sounds without an identifiable cause, this may indicate a hardware defect in the electronic circuit or the LCD screen. In this case, contact customer service or consider a replacement, as this lamp is not user-repairable (the casing should not be opened according to the safety manual).

Question 3

How to deactivate or delete the alarm on the LIVARNO IAN 367070.2101 table lamp?

Accepted Answer

To deactivate or delete the alarm on your LIVARNO IAN 367070.2101 table lamp, follow these simple steps:

Steps to deactivate the alarm

Locate the alarm button: On the control panel of the lamp, look for a button marked "Alarm", "Wake-up" or a similar symbol.
Deactivating the alarm: Press this button once to deactivate the alarm. If that doesn't work, hold it down for a few seconds until the alarm is deactivated.
Using the screen (if available): If your lamp is equipped with a screen, navigate through the settings using the control buttons to find the alarm option, then select "Deactivate" or "Delete".
Resetting the lamp: If the previous steps do not work, unplug the lamp from the electrical outlet for about a minute, then plug it back in. This may reset the settings and deactivate the alarm.

These methods generally allow you to delete the alarm on this model. If the alarm persists, the lamp may have a specific feature, but these tips are suitable for the majority of users.

Question 4

How to solve the alarm problem that goes off randomly at 0:00 on the LIVARNO IAN 367070.2101 table lamp?

Accepted Answer

Your LIVARNO IAN 367070.2101 table lamp has an alarm/wake-up function that can be turned on and off. If an alarm goes off randomly at 0:00 (midnight), it is usually because the alarm function is activated with a wake-up time set to 00:00 without you having intentionally programmed it. Here’s how to quickly resolve this issue.

First solution - Completely disable the alarm: Press the mode button (no. 4) on the back of the lamp to switch to alarm mode. You will see the display change to alarm mode. Then press the selection buttons (no. 6) several times to disable the alarm symbol in the function display. Once the alarm symbol disappears, press the mode button again to return to time mode. The alarm will no longer sound.

Second solution - Reprogram the wake-up time: If you wish to keep the alarm function, press the mode button (no. 4) to switch to alarm mode. Press the selection button (no. 5) to access the settings. Using the directional buttons (no. 6), first set the desired hour (for example, 07:00), confirm with the selection button, then set the minutes, and confirm again. Continue to set the snooze delay in minutes if desired, and finally choose one of the 8 available alarm tones. This procedure automatically clears any previous settings at 0:00.

Reset the lamp (as a last resort): If the problem persists, completely unplug the lamp from the electrical outlet for at least one minute. This action resets the stored settings, but you will need to reconfigure the time, date, and alarm once you plug it back in. Note that the CR2032 battery installed at the back of the lamp keeps these settings even when powered off, which explains why the alarm could continue to function even during a power outage.

If the unacceptable alarm problem at 0:00 persists despite these actions, contact LIVARNO/EGLO France customer service at +33 389 625 030 (line indicated in the warranty) stating your product reference IAN 367070.2101. A hardware malfunction of the internal electronic module may then be the cause.

User manual LIVARNO Table lamp : user manuals and guides in PDF

Models LIVARNO Table lamp most viewed

Other categories LIVARNO

Recent questions about Table lamp LIVARNO