Question 1

How to reset the HQ VDPC146 effects machine?

Accepted Answer

Your HQ VDPC146 effects machine has several reset levels depending on your needs. Here’s how to proceed:

Hardware reset (power cycle)

Turn off the device by pressing the power button
Unplug the power cable from the electrical outlet
Wait 5 to 10 minutes to allow the device to fully discharge
Plug the power cable back in
Turn the device back on

This procedure resets the device to its normal operating state and generally resolves temporary freezes or malfunctions. Note that your VDPC146 has an included backup battery (model 3/V80H'VP2) that preserves all your saved programs and scenes, even during a power outage.

Complete memory erase

If you want to delete all saved programs and scenes and return to a completely blank device, use this procedure:

Press and hold the RECORD button
Press and release the REC CLEAR button
Release the RECORD button

This operation completely erases the memory of your effects machine.

Selective program erase

If you want to keep certain items but only delete all stored programs, use this alternative:

Press and hold the RECORD button
Press the PRESET A flash buttons in the order: 1 - 3 - 2 - 3
Release the RECORD button

After any of these operations, your VDPC146 will be reset. If you still encounter issues after the reset, we recommend contacting technical support for further assistance.

Question 2

What to do if a problem occurs after replacing the battery of the HQ VDPC146 effects machine?

Accepted Answer

If you encounter a problem after replacing the battery of your HQ VDPC146 effects machine, here are several points to check to resolve the situation:

1. Check the battery orientation

Make sure the battery is inserted the right way, respecting the polarities indicated in the battery compartment (the + and - must match the markings).

2. Type of battery

Only use the recommended type of battery for your device. An unsuitable battery can cause malfunction.

3. Connections and contacts

Check that the battery contacts are clean, free of corrosion, and that the connections are tight and in good condition.

4. Resetting the device

If your machine has a reset button, try using it after changing the battery to restore normal operation.

If the problem persists despite these checks, it may be helpful to contact a specialized technical service for a thorough diagnosis.

Question 3

What should I do if the blackout indicator on the HQ VDPC146 effects machine is flashing and won't turn off?

Accepted Answer

The BLACK OUT indicator on your HQ VDPC146 is a yellow LED that lights up when you activate the blackout function to cut the DMX signal to all connected devices. If this indicator is continuously flashing and does not turn off after pressing the BLACK OUT button, it generally indicates an electronic problem requiring technical intervention.

Start by performing a complete power cycle: turn off the device, unplug the power adapter (12-20 VDC / 500 mA), wait at least 2-3 minutes to allow the electronics to reset, then plug it back in and restart. This operation resets the internal circuits and often resolves issues with faulty LEDs.

While the device is off, carefully check all connections: ensure that the power cable is firmly plugged into the DC jack, that the DMX XLR output cable is properly connected at both ends, and that all MIDI connectors (if used) are seated correctly. A poorly connected or damaged cable can create false contacts causing the indicator to flash.

If the device has been operating for a long time before the problem appeared, overheating may be the cause. The VDPC146 should operate between 5 and 35°C. Allow the device to cool down for at least 30 minutes before restarting to avoid malfunctions due to temperature.

If the indicator is still flashing after these steps, check the protection fuse: the VDPC146 model contains a F 0.5 A / 250 V fuse that may blow in case of overload or internal short circuit. A blown fuse often causes abnormal LED behavior. If you are comfortable accessing it, check its condition and replace it if necessary.

Persistent flashing of the BLACK OUT indicator after these checks almost certainly indicates an internal hardware fault (short circuit, faulty component, etc.). The memory backup battery (3/V80H'VP2) or a defective internal connection may also be the cause. In this case, contact a qualified technician or Velleman's technical service for diagnosis and warranty repair.

User manual HQ Effect machine : user manuals and guides in PDF

Models HQ Effect machine most viewed

Other categories HQ

Recent questions about Effect machine HQ