AquaShield AWH1069 - Water heater PHILIPS - Free user manual and instructions

Brand	Philips
Model	AquaShield AWH1069
Product Type	Electric Water Heater
Capacity	10 liters
Power Rating	1500 W
Voltage	220-240 V
Frequency	50/60 Hz
Temperature Range	35°C – 75°C
Installation Type	Wall-mounted, under-sink
Dimensions (H x W x D)	650 x 340 x 320 mm
Weight (empty)	6.2 kg
Material	Stainless steel inner tank
Safety Features	Anti-scald, overheat protection, pressure relief valve
Control Type	Mechanical knob with temperature indicator
Energy Efficiency	Class A
Water Connection	1/2 inch BSP inlet and outlet
Included Accessories	Safety valve, mounting bracket, installation manual
Maintenance	Descaling every 6 months; replace anode rod every 2 years
Warranty	2 years limited
Certifications	CE, RoHS

Frequently Asked Questions - AquaShield AWH1069 PHILIPS

How do I install the Philips AquaShield AWH1069 water heater?

Installation should be performed by a qualified plumber. The heater must be wall-mounted vertically, with the water inlet and outlet connected properly. Ensure the pressure relief valve is fitted and the unit is earthed. Refer to the manual for detailed steps.

What is the recommended temperature setting for daily use?

For energy efficiency and safety, set the thermostat between 50°C and 60°C. This prevents bacterial growth and reduces the risk of scalding.

How do I adjust the water temperature?

Turn the temperature knob located on the front panel. The indicator shows approximate temperature levels. Turn clockwise to increase temperature, counterclockwise to decrease.

Why is water not heating?

Check if the unit is powered on and the circuit breaker is not tripped. Verify the thermostat setting is above the current water temperature. If the problem persists, the heating element may be faulty and require replacement.

How often should I descale the water heater?

Descaling is recommended every 6 months, especially in hard water areas. Use a descaling solution suitable for electric water heaters or follow the procedure in the manual to remove limescale buildup.

What does the pressure relief valve do?

The pressure relief valve automatically releases excess pressure inside the tank to prevent bursting. It is a critical safety component. Test it periodically by lifting the lever; water should flow out. If it does not release, replace the valve.

Can I use an extension cord with the water heater?

No, do not use an extension cord. The water heater must be directly connected to a dedicated power outlet to avoid overheating and fire hazards.

How do I replace the anode rod?

The anode rod protects the tank from corrosion. To replace, turn off power and water supply, drain the tank, unscrew the old anode rod (usually located on top), and install a new one. Use Teflon tape on threads. Check every 2 years.

What should I do if there is a water leak?

Immediately turn off the power and water supply. Dry the area and inspect connections. Common causes: loose fittings, damaged seals, or a crack in the tank. Tighten connections or replace faulty parts. If the tank is leaking, contact customer service.

Is the water heater suitable for outdoor installation?

No, this water heater is designed for indoor use only. Exposure to rain, snow, or extreme temperatures can damage the unit and void the warranty.

USER MANUAL AquaShield AWH1069 PHILIPS

©2023 AquaShield All rights reserved.

Philips and the Philips Shield Emblem are registered trademarks of Koninklijke

Phillips N.V. and are used under license. This product has been manufactured by and is sold under the

responsibility of Guangdong AquaShield Health Technology Company Limited and Guangdo

AquaShield Health Technology Company Limited is the warrantor in relation to this product.

Exterior view of a white electronic device labeled 'PNLIDS' with control buttons (no additional text or symbols visible)

说明书

目录

Technical line drawing of a rectangular enclosure with vertical supports and labeled dimensions (no text or symbols)

8 安装及使用

8.1 安装前注意事项