ORF5060 - Measurement Owon - Free user manual and instructions

Product Type	Digital Multimeter
Model	ORF5060
Brand	Owon
Display	LCD with backlight, 6000 counts
DC Voltage Accuracy	±0.5% + 5 digits
AC Voltage Bandwidth	40 Hz to 400 Hz
Resistance Range	0.1 Ω to 60 MΩ
Capacitance Range	1 nF to 10 mF
Frequency Measurement	Up to 10 MHz
Safety Rating	CAT III 600V
Power Supply	2 x 1.5V AAA batteries
Auto Power Off	Yes, after 15 minutes
Dimensions	190 x 91 x 52 mm
Weight	Approx. 400 g (including batteries)
Operating Temperature	0°C to 40°C
Storage Temperature	-10°C to 50°C
Input Protection	Overload protection for all ranges
Accessories Included	Test leads, battery, user manual
Warranty	1 year limited

Frequently Asked Questions - ORF5060 Owon

How do I replace the batteries in the Owon ORF5060?

Turn off the meter and remove the protective holster. Slide off the battery cover on the back. Replace the two AAA batteries with fresh ones, observing polarity. Reattach the cover and holster.

What is the maximum voltage this multimeter can measure?

The Owon ORF5060 can measure up to 600V AC/DC in the voltage range. However, always start with the highest range and switch down for a safe measurement.

How do I use the relative measurement function?

Press the REL button to zero out any offset. The meter will store the current reading and subtract it from subsequent measurements. This is useful for measuring resistance or small capacitances.

What does the 'OL' reading mean?

'OL' stands for Over Limit. It indicates the input value exceeds the selected range. Select a higher range to get a valid reading.

Can I measure AC current with this meter?

Yes, the ORF5060 can measure AC current up to 10A. Use the manual range selection to choose the appropriate current range. Do not exceed 30 seconds for high current measurements.

How do I enable the backlight?

Press the BACKLIGHT button to turn on the display backlight. It will automatically turn off after 10 seconds to save battery.

What is the input impedance for voltage measurements?

The input impedance for DC voltage measurements is 10 MΩ. For AC voltage, it is 10 MΩ in parallel with less than 100 pF.

How do I test continuity?

Set the rotary switch to the continuity/Diode position. Connect the test leads to the circuit. The meter will buzz if the resistance is less than about 50 Ω.

What safety precautions should I take?

Always use the meter within the specified CAT rating (CAT III 600V). Do not measure voltages above 600V. Use proper test leads and inspect them for damage. Do not exceed 10A for more than 30 seconds.

How do I store the meter when not in use?

Turn off the meter, remove the test leads, and store in a dry, moderate temperature environment. Remove batteries if storing for more than a month to prevent leakage.

USER MANUAL ORF5060 Owon

Near Field Probe Set

Instruction Manual

May. 2024 edition V1.0.0

Copyright © LILLIPUT Company. All rights reserved.

The LILLIPUT's products are under the protection of the patent rights, including ones which have already obtained the patent rights and those which are applied for. The information in this manu replace all materials published.

The information in this manual was correct at the time of printing. However, LILLIPUT will continue to improve products and reserves the rights to change specification at any time without notice.

owon is the registered trademark of the LILLIPUT Company.

Fujian LILLIPUT Optoelectronics Technology Co., Ltd.

No. 19, Heming Road

Lantian Industrial Zone, Zhangzhou 363005 P.R. China

Tel: [phone] Fax: [phone]

Web: www.owon.com.cn E-mail: [e-mail]

www.owon.com.cn

1. Specifications

Model	Instruction
ORF5060-001	Near Field Probe:It is mainly used to locate and detect the leak electricFrequency rage: 1MHz-6GHzResolution: 3mmImpedance: 50Ω
ORF5060-002	Near Field Probe:It is mainly used to locate and detect the leak magnetFrequency rage: 1MHz-6GHzResolution: 13mmImpedance: 50Ω

Model	Instruction
ORF5060-003	Near Field Probe:It is mainly used to locate and detect the leak magnFrequency rage: 1MHz-6GHzResolution: 30mmImpedance: 50Ω
ORF5060-004	Near Field Probe:It is mainly used to locate and detect the leak magnFrequency rage: 1MHz-6GHzResolution: 45mmImpedance: 50Ω