Aironet 602i - Access Point CISCO - Free user manual and instructions
Find the device manual for free Aironet 602i CISCO in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Cisco Aironet 602i Access Point |
| Standards | IEEE 802.11a/b/g |
| Frequency Band | 2.4 GHz and 5 GHz |
| Maximum Data Rate | 54 Mbps per band |
| Dimensions (W x D x H) | 8.0 x 8.0 x 1.8 in (20.3 x 20.3 x 4.6 cm) |
| Weight | 1.1 lb (0.5 kg) |
| Power Input | 48V DC via Power over Ethernet (PoE) or external power supply |
| Power Consumption | 12.5W typical |
| Ethernet Ports | 1 x 10/100 BASE-T (RJ-45) |
| Antenna | Internal dual-band diversity antennas |
| LED Indicators | Power, Ethernet, Radio (2.4 GHz and 5 GHz) |
| Management | Console port, HTTP/HTTPS web interface, Telnet/SSH, SNMP, Cisco IOS CLI |
| Security | WEP, WPA/WPA2 (TKIP/AES), 802.1X, MAC filtering, SSID broadcast control |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Humidity | 10% to 90% non-condensing |
| Mounting | Ceiling or wall mount (kit included) |
| Compliance | FCC, CE, IC, UL, RoHS |
| Cleaning | Wipe with a dry cloth; do not use liquids or sprays |
| Spare Parts | Power injector, mounting bracket, console cable (available from Cisco) |
| Repair | No user-serviceable parts; contact Cisco support for repairs |
Frequently Asked Questions - Aironet 602i CISCO
How do I perform a factory reset on the Cisco Aironet 602i?
To reset to factory defaults, press and hold the Mode button on the back of the access point while powering it up. Hold for about 10 seconds until the LEDs flash. Alternatively, use the write erase command via the CLI.
What PoE standard does the Aironet 602i support?
It supports IEEE 802.3af Power over Ethernet. A PoE injector or PoE switch providing 48V DC is required.
How can I access the web interface?
Connect via Ethernet and assign a static IP in the same subnet as the AP (default IP: 10.0.0.1). Open a browser and enter https://10.0.0.1. Default username is Cisco and password is Cisco (case-sensitive).
Can I mount the Aironet 602i outdoors?
No, this device is designed for indoor use only. It is not weatherproof and should be installed in a climate-controlled environment.
How do I update the firmware?
Download the latest firmware from Cisco.com. Access the web interface, go to Administration > Software Upgrade, and upload the file. Do not power off during the process.
What security options are available?
The device supports WEP, WPA and WPA2 (with TKIP or AES), 802.1X authentication, and MAC address filtering. For best security, use WPA2-AES.
Why is the Radio LED not lit?
This indicates the radio is disabled. Enable it via the web interface under Wireless > Radio Settings. Alternatively, check if the country code is configured correctly.
Can I use a different antenna?
The Aironet 602i has integrated internal antennas and does not have external antenna connectors. Antenna replacement is not possible.
How do I configure VLANs?
VLAN support is available via the CLI. Use the interface dot11Radio and interface FastEthernet commands to set native VLAN and allowed VLANs. Refer to the manual for detailed steps.
Does the device support mesh networking?
No, the Cisco Aironet 602i is a standalone access point and does not support mesh or wireless bridging. It requires a wired connection to the network.
User questions about Aironet 602i CISCO
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Point in PDF format for free! Find your manual Aironet 602i - CISCO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Aironet 602i by CISCO.