ZLOC2.2 - Convertisseur audio actif PHOENIX GOLD - Free user manual and instructions

Brand	Phoenix Gold
Model	ZLOC2.2
Product Type	Line Output Converter / Signal Processor
Dimensions (H x W x D)	1.5 x 4.5 x 3 inches
Weight	0.5 lbs (approx.)
Power Requirement	Passive (no external power needed)
Input Type	Speaker-level (2 channels)
Output Type	RCA line-level (2 channels)
Gain Adjustment	Yes, adjustable input sensitivity
Frequency Response	20 Hz - 20 kHz
Signal-to-Noise Ratio	> 90 dB
Total Harmonic Distortion (THD)	< 0.05%
Protection Features	Short circuit protection
Mounting Type	Screw mount (brackets included)
Input Connector	Screw terminals
Output Connector	RCA jacks
Chassis Material	Metal
Compatibility	Most car audio head units and amplifiers
Warranty	1 year limited

Frequently Asked Questions - ZLOC2.2 PHOENIX GOLD

What is the Phoenix Gold ZLOC2.2 used for?

The ZLOC2.2 is a line output converter that allows you to connect a car audio amplifier to a factory head unit by converting speaker-level signals to RCA line-level outputs.

Does the ZLOC2.2 require external power?

No, the ZLOC2.2 is a passive device and does not need an external power source. It uses the signal from the speaker wires.

How many channels does the ZLOC2.2 support?

It supports 2 channels (left and right) for both input and output, making it ideal for stereo systems.

What type of input connectors does it have?

The ZLOC2.2 has screw terminals for connecting speaker wires. Be sure to strip the wires and tighten the screws securely.

Can I use the ZLOC2.2 with a high-power head unit?

Yes, it can handle typical factory head unit power levels. It has an adjustable gain to accommodate different input levels.

How do I adjust the gain on the ZLOC2.2?

Use a small flathead screwdriver to turn the gain adjustment potentiometer located on the side of the unit. Turn clockwise to increase sensitivity.

What is the frequency response of the ZLOC2.2?

The frequency response is 20 Hz to 20 kHz, covering the full audible range with minimal distortion.

Does the ZLOC2.2 have any protection features?

Yes, it includes short circuit protection to prevent damage from wiring errors.

What are the dimensions of the ZLOC2.2?

Approximately 1.5 x 4.5 x 3 inches, compact enough to be mounted behind the head unit or under the dash.

Is the ZLOC2.2 compatible with aftermarket amplifiers?

Yes, it works with most aftermarket amplifiers that have RCA inputs. The line-level output ensures a clean signal.

USER MANUAL ZLOC2.2 PHOENIX GOLD

Introducing the Phoenix Gold active line-output converters (LOC) - the essential solution for enhancing your vehicle's audio system. While many vehicles now come with integrated amplifiers, the original OEM system often falls short in terms of performance. Replacing the entire audio system can be costly and sometimes not feasible. That's where our LOC converters step in. Not only do they reduce distortion, but they also allow for seamless integration of aftermarket audio components into your OEM system. Gone are the days of being unable to upgrade your head unit - our LOC converters cleverly bypass OEM resistance, all while eliminating unwanted system noise. Upgrade your audio experience today with our advanced OEM integration solution.

ZLOC2.2 / ZLOC4.4 FEATURES OVERVIEW

1

WWW.PHOENIXGOLD-EU.COM

PHOENIX GOLD

ZLOC ACTIVE LINE-OUTPUT CONVERTERS

ZLOC4.4 TYPICAL WIRING DIAGRAM

PHOENIX GOLD

ZLOC ACTIVE LINE-OUTPUT CONVERTERS

TECHNICAL SPECIFICATIONS

The ZLOC active line output converters share the performance specifications listed below; however, they vary in terms of the number of inputs and outputs they possess. ZLOC2.2 = 2-Channels in and 2-Channels out, ZLOC4.4 = 4-Channels in and 4-Channels out.

ITEM	ZLOC0.2	ZLOC4.4
Speaker Input	2OH	4OH
Output	4OH	4OH
FLOO ID	Yes	Yes
RUM OUT	Yes	Yes
Load Select	10 Ohm / 60 Ohm / 20K Ohm
Ground Isolation	GND/ISO/200 Ohm
Gas	Yes-X1	Yes-X2
Clipping	Yes-X1	Yes-X2
Center Frequency	20Hz, 11kHz	20Hz, 110Hz
Base Level	30~50Hz	30~50Hz
Turn On Mode	FEI 0.00/PADRO	FEI 0.00/PADRO
Input Mode	N/A	20Hz, 10Hz
Remote	None	None
Dimension(s)LWH@mm	130.6x82x24.8mm	150.6x82x24.8mm
Chassis Body	Aluminum	Aluminum

Operating Voltage	8 to 22V
Input Sensitivity	0.5 to 32V
Max 40V as Input	Max be 20V-onn load
Output Voltage	Max 7.5V @ 14.4V
Input Impedance	10-Ohm / 80 Ohm / 20K Ohm
Signal-to-Nutless	>100dB @ 4V output
Trans-H	± 10 dB
Frequency Responses	10-20kHz
Max Current Draw	120 - 150 mA
Output Impedance	< 120 ohm
Gain	-28 to 0dB
Turn-On Trigger, DC	3 to 7V
Termine Gauge	Quick Connect / 164 AWG

WW

m = 311

2

PHOENIX GOLD

ZLOC ACTIVE LINE-OUTPUT CONVERTERS

IMPORTANT INSTALLATION PRECAUTIONS

1) Connect all components with the power turned off, ensuring that the battery ground is connected in the final step.

the final stop:

2) Connect the ZLOC 12V connector with a constant +12V power source to ensure a stable power supply. It is advised to use a 15 AWC wire for optimal performance.

It is advised to use a 10-fold RNA spimer partitioning.

3) Before inserting any wire, ensure that the terminals are completely open.

4) To optimise the device's performance and longevity, it must be placed on a stable, dry, and well-ventilated

surface, away from any moisture, heat, and dirt sources.

5) Do not mount directly on the vehicle's body, frame, or structure.

The following table provides the information in the following table:

1. First passing the device near the bus bus to prevent potential transduction.

7) To ensure peak performance, it is advisable to keep RCA cables as far away as possible from the vehicle's wiring, news cables, and output speaker uses. By doing so, interference can be minimized

resulting in superior audio quality.

1. To including noise and power loss, keeping the focus on about or possible in adjords

(3) To minimize hours and power too, keeping the wind as short

9) Professional installation is recommended for optimal results.

10) Adjust the remote level control to a position easily reachable by the driver.

TROUBLE SHOOTING

POWER LED IS ON, NO OUTPUT

1.2.3.1.1

- Verify the source unit's output - Ensure the input gain control is functioning properly

- Ensure the input-gam control is functioning properly - Check the quality and connection of the RCA cable

- Inspect the speaker and wiring for any potential short

- Assets for any signs of amplifier damage

NO SOUND ON ONE CHANNEL

- Switch the left/right input to inspect the source

- If the sound switches, it indicates a faulty source or signal cable.

- Perform a left/right speaker swap to test the functionality of the speakers. If the sound does not switch, it indicates a problem with the speaker so he

- If these solutions prove ineffective, it is advisable to seek guidance from an authorised

Dealer to address the issue at hand.

WARRANTY

Phoenix Gold products come with a limited warranty and are covered by our regional distribution partners and their terms and conditions. You can find out more information by contacting you local retail or distributors.

DISCLAIMER

Ensure your safety and the well-being of those around you by following these essential guidelines:

- Keep all product materials and packaging away from children, pets, or anyone at risk of suffocation

- Exposure to noise levels above 85 dB can cause permanent hearing damage.

- Extreme sound frequencies reduce perception abilities that are essential in road do not let loud volume distract from being mindful behind the wheel.

• Phoenix Gold takes no responsibility for any physical harm or damage caused by improve

their products.

- Ensure that all metals and raw materials are disposed of in accordance with local regulations and environmental standards to minimize any negative impact on the environment.

environmental standards to minimise any negative impact on the environment.

www

V.PHOENIXGOLD-EU.COM

6

ZLOC ACTIVE LINE-OUTPUT CONVERTERS

PHOENIX GOLD

FEATURES

1) Connect the speaker inputs to your head unit or amplifier's speaker outputs to receive the signal your amplifier may not be capable of handling.

（一）本次股东大会的召集和召开程序

2) Outputs: Establish a connection with the inputs of the precisely what the amplifier needs to function optimally.

SLP114. Pumetan, 2017, 10: 19518 in the STT and Tm

6) HEM IN. HEM turn-on input. It works with the "HEM" in the "turn-on mode.

4) To connect aftermarket audio equipment, use the "Rem In" option and disable "REM Out". The "Rem-cut" function will always remain active when the T1 CC is turned on, regardless of the turn or method. Make sure

to connect it to only one aftermarket amplifier.

5) Many CFM head units require a resistance load to enable audio signal output. Without this load, a ZLOC

would not function properly. For most of these systems, 10-ohm or 60-ohm is compatible. Choose

10-ohm/60-ohm for those systems and 20k-ohm for all others.

6) Ground Isolation: Experiment with various switches if you encounter unwanted *alternator whine* or

"ground noise" interfering with the audio signal. Keep in mind that the power ground and

are not interconnected. Remember to turn on the converter before making any switches.

GND: power supply has the same ground as the audio.

ISO: The power supply ground is separated from the audio.

7) Gain: Adjusts the output signal for every channel pair. 9.5V RMS

8) Clip: If the LEDs light up, it indicates a distorted output signal

QI LPE: The filtering of signals above Q501in can be tangled as as well. The two-way channels are primarily

intended for subwoofers.

10! Bass Level: This feature allows you to finely tune the bass levels within a range of -9 to +9dB, specifically

targeting the centre frequency.

11) Turn-on Mode: It provides the drivers with the convenience of choosing different ways to activate the device.

PDM: This approach follows a traditional method of refining the 71.00, providing our existing results

REM: This approach follows a traditional method of activating the ZLOC, granting you precise control over its ignition and enabling you to determine the specific timing for turning it on or off.

DC: The R8-HTL is activated when the head unit is turned on. It is important to ensure that the signal from

the head unit has a DC offset.

AUDIO: Selecting VOX activates the ZLOC, triggering it only when the head unit plays radio, CD music, or Bluetooth streams. By doing this, it optimises functionality without compromising on quality or interrupting

other audio sources.

12) Input Mode: To obtain four outputs from two speaker-level inputs, switch to 2CH. The fr

Key right words: to sustain real outpands from two speakers over inputs, which is learn. This is receive the same source, but you will retain the flexibility to set LPI or Boost as needed.

12) PASS CURE(Constant Unable Base - enhancement), is a single hand squaring consisting of two

13) BASB COBE. [Constant Enable Base - enhancement] is a single-band equancer consisting of two components: a processor module that can be conveniently mounted near the subwoofer amplifier and a

wired remote control that can be elegantly installed on the dashboard. The remote control allows you to

conveniently adjust the centre frequency (ranging from 20 to 110Hz ) and boost level (ranging from -9dB

to +9dB) with its intuitive knob. Additionally, the knob can be used to toggle the processor on and off easily

The processor module features two switches that control infrasonic filtering and Q. The wide low-Q setting

(Q = 2) is commonly used to enhance overall sound quality, particularly with sealed enclosures. On the other hand, the power high. Setting (Q) is recommended for achieving maximum output.

hand, the narrow high-Q setting (Q = 6) is recommended for achieving maximum output.

The Base CUBE offers a versatile third-order infrasonic filter that can be switched between a fixed cut-off

frequency of 25 Hz and an adjustable mode. In the adjustable mode, which is recommended for use with

vented including, the inelastic cut-off frequency is set one-third of an octave below the centre frequency, adjusting accordingly as the centre frequency changes. This feature allows for animal control and flexibility

in shaping the audio output.

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated placeholder underscores where none exist in the GT. Hence, the OCR result is inconsistent with the Ground Truth.

3

WWW.PHOENIXGOLD-EU.COM

6

PHOENIX GOLD

ZLOC ACTIVE LINE-OUTPUT CONVERTERS

© 2023 Phoenix Gold A Brand of AAMP Global www.phoenixgold-eu.com

UK CA CE