AX-ADCH02 - Car kit Axxess - Free user manual and instructions

Product Type	Car Mount Kit
Brand	Axxess
Model	AX-ADCH02
Compatible Devices	Smartphones up to 6.5 inches
Mounting Type	Dashboard and windshield suction cup
Material	ABS plastic and silicone grip
Dimensions	12 x 6 x 8 cm
Weight	150 g
Color	Black
Rotation	360-degree swivel
Installation	Tool-free, adjustable arm
Safety Features	Non-slip pads, secure locking mechanism
Cleaning	Wipe with a soft, dry cloth
Repairability	Not user-serviceable; contact support for issues
Package Contents	Mount, suction cup, adhesive pad, user manual

Frequently Asked Questions - AX-ADCH02 Axxess

How do I install the AX-ADCH02 car mount?

Clean the mounting surface, attach the suction cup or adhesive pad, then secure your device using the adjustable grip. Refer to the user manual for detailed steps.

Is the mount compatible with all phone sizes?

It fits most smartphones up to 6.5 inches. Check your phone's dimensions; the grip expands to accommodate various widths.

Can I rotate my phone while it's mounted?

Yes, the mount features a 360-degree swivel for portrait or landscape viewing.

Will the suction cup leave residue on my windshield?

If properly cleaned, the suction cup should not leave residue. Avoid prolonged exposure to direct sunlight.

How do I clean the car mount?

Use a soft, dry cloth to remove dust. For sticky residue, a damp cloth with mild soap can be used, then dry thoroughly.

What is the warranty period for the AX-ADCH02?

Axxess typically offers a 1-year limited warranty. Contact seller or manufacturer for details.

Can I use this mount on a textured dashboard?

The adhesive pad is designed for flat, smooth surfaces. Textured dashboards may require the suction cup on glass.

Does the mount block any phone buttons?

No, the grip design leaves access to side buttons and ports. Ensure proper alignment when placing your phone.

Is the mount adjustable for different viewing angles?

Yes, the arm and swivel allow multiple angles. Tighten the joints if needed for your preferred position.

What if the suction cup loses grip?

Clean both the cup and mounting surface. If the issue persists, the suction cup may be replaced; check for spare parts.

USER MANUAL AX-ADCH02 Axxess

Installation Instructions for AX-ADCHO2

AX-ADCHO2

Chrysler vehicles 2007-up

The AX-ADCH02 is designed to and MUST be used with the AX-ADBOX1 or AX-ADBOX2 (sold separately). Please refer to AX-ADBOX1 or AX-ADBOX2 for 16-pin connector instructions.

APPLICATIONS

CHRYSLER

200 2011-up*

300 2008-up*

Aspen 2008-2009*

Sebring 2007-2010*

Town & Country 2008-up*

DODGE

Magnum 2008-2009*

Nitro 2007-up*

Ram 1500 2009-up*

Ram 2500/3500 2010-up*

DODGE

Avenger 2008-up*

Caliber 2009-2010*

Challenger 2009-up*

Charger 2008-2010*

Dakota 2008-up*

Durango 2008-up*

Grand Caravan 2008-2010*

Journey 2009-2010*

JEEP
Commander	2008-2010*
Compass	2009-up*
Grand Cherokee	2008-up*
Liberty	2008-up*
Patriot	2009-up*
Wrangler	2007-up*

MITSUBISHI
Raider	2008-2009*

Note: * indicates if vehicle is amplified it is digitally amplified

INTERFACE COMPONENTS

22-pin harness to 22-pin Chrysler harness with stripped leads 4-pin harness with stripped leads

TOOLS REQUIRED

- Cutting tool • Tape • Crimping tool - Connectors (i.e. butt-connectors, bell caps, etc.)

Caution

Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.

*Note: Refer also to the instructions included with the aftermarket radio.

CONNECTIONS TO BE MADE

From the 16-pin harness with stripped leads (included with interface)

• Connect the White wire to the left front positive speaker output of the aftermarket radio
• Connect the White/Black wire to the left front negative speaker output of the aftermarket radio
• Connect the Gray wire to the right front positive speaker output of the aftermarket radio
• Connect the Gray/Black wire to the right front negative speaker output of the aftermarket radio

Only make the following connections if the vehicle is amplified

• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the Purple wire to the radio's right rear positive speaker output.
• Connect the Purple/Black wire to the radio's right rear negative speaker output.

(continued on next page)

AX-ADCHO2

CONNECTIONS TO BE MADE (continued)

From the 22-pin Chrysler harness:

• Connect the Yellow wire to the radio's 12-volt battery or memory wire.
• Connect the Black wire to the radio's ground wire.
• Connect the Blue/White wire to the radio's amp turn on wire if populated on the factory side

Amplified vehicles:

- Connect the two 4-pin connectors with the Purples and Greens wires in it together.

Non-amplified vehicles:

• Disconnect the two 4-pin connectors with the Purples and Greens in it.
• From the 22-way Gray connector, connect the 4-pin with the Whites and Grays to the 4-pin with the Purples and Greens coming from the Black 22-way connector.
• Connect the 4-pin harness with stripped leads to the 4-pin with the Greens and Purples coming from the Gray 22-pin connector.
• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the Purple wire to the radio's right rear positive speaker output.
• Connect the Purple/Black wire to the radio's right rear negative speaker output.

12-Way Harness:

This harness is for the ASWC-1 (sold separately). Please refer to the ASWC-1 instructions for programming.

Installing the AX-ADCH02

• With all connections completed to the aftermarket radio, plug the 22-pin harness into the vehicles wiring harness.
• Reconnect the negative battery terminal.
• Cycle the key, by turning the ignition on for 30-seconds. Then off and on again to test the radio.

Testing the AX-ADCH02

• Turn the ignition on if not already, and then turn the radio on to verify that the radio works. Check balance and fader controls for proper operation.
• To adjust the overall volume of your audio system, rotate the potentiometer which is located on the 16-pin side of the interface clockwise.

Installation Instructions for AX-ADCHO2

AX-ADCHO2