LC42 - Washing machine REX - Free user manual and instructions

Product Type	Washing Machine
Brand	Rex
Model	LC42
Category	Freestanding
Load Capacity	7 kg
Spin Speed	1200 rpm
Dimensions (H x W x D)	85 cm x 60 cm x 55 cm
Weight	65 kg
Power Supply	220-240 V, 50 Hz
Energy Efficiency Class	A++
Programs	Cotton, Synthetics, Delicates, Quick Wash, Eco, Rinse & Spin
Additional Functions	Delay Start, Child Lock, Auto Water Level, Stain Treatment
Display	LED Digital
Noise Level (Wash/Spin)	56 dB / 74 dB
Water Consumption per Cycle	45 L
Drum Material	Stainless Steel
Door Type	Front Load, 180° Opening
Installation Type	Freestanding
Maintenance	Clean filter regularly, check hoses, run drum clean cycle monthly
Safety Features	Overflow protection, unbalanced load detection, door lock during operation
Spare Parts Availability	Belt, pump, door seal, control board, filter, hoses
Repairability Index	7.5/10
Warranty	2 years

Frequently Asked Questions - LC42 REX

How do I install the washing machine properly?

Ensure the machine is level on a solid floor. Remove transport bolts, connect water inlet hose to cold water tap (3/4 inch thread), attach drain hose to a standpipe or sink, and plug into a grounded outlet. Refer to manual for detailed steps.

What should I do if the machine doesn't start?

Check that the door is fully closed and latched. Ensure water supply is turned on and power cord is plugged in. Verify the program dial is set correctly and press Start/Pause. If still not starting, check child lock and reset the machine.

How do I clean the detergent drawer?

Remove the drawer by pulling it out and pressing the release lever. Rinse under warm water to remove residue. Use a brush to clean the compartment. Reinsert securely.

Why is the machine leaking water?

Common causes: loose hose connections, damaged door seal, clogged filter, or over-sudsing. Tighten all connections, inspect the seal for tears, clean the filter, and use appropriate detergent.

What is the maximum load capacity?

The maximum load capacity is 7 kg of dry laundry. Overloading may affect washing performance and cause excessive vibrations.

How do I use the delay start function?

Select your program, then press the Delay Start button repeatedly to set the delay time (1-24 hours). The display will show the remaining time including delay. Press Start/Pause to begin.

What should I do if the drum doesn't spin?

Check if the machine is in a non-spin program (e.g., Delicates). Look for unbalanced load - redistribute clothes. Ensure the drain pump is not clogged. If the issue persists, the belt or motor may need servicing.

How often should I clean the filter?

Clean the drain pump filter every 2-3 months or when the machine indicates a clog. For optimal performance, also clean the water inlet filters at the hose connection yearly.

Can I use bleach or fabric softener?

Yes, but follow dosage instructions. Add bleach to the designated compartment (marked with a bleach symbol) and fabric softener to the ‘softener’ compartment. Do not overfill.

What does the error code 'E10' mean?

Error code E10 indicates a water supply issue. Check that the water tap is fully open, the inlet hose is not kinked, and the water pressure is adequate. Turn off the machine and restart after fixing.

USER MANUAL LC42 REX

Simple line drawing of a washing machine connected to a funnel and a sink, with no text or symbols present.

Line drawing of a hand holding a faucet with a small component, no text or symbols present

Line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Diagram of a bathroom sink with a pipe fitting and a faucet, no text or symbols present

Hand holding a mechanical component with a pointed tip and threaded base (no text or symbols visible)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Line drawing of a hand inserting a device into a drawer (no text or symbols)

Line drawing of a hand inserting a device into a drawer (no text or symbols)

Illustration of hands installing or adjusting a device panel (no text or symbols visible)

Hand inserting a small component into a device (no text or symbols visible)

Hand inserting a component into a device (no text or symbols visible)

Hand inserting a small object into a box, no text or symbols visible