PMD24 - Detector Pyle - Free user manual and instructions

Product Type	Metal Detector
Brand	Pyle
Model	PMD24
Detection Depth	Up to 6 inches for small coins, larger objects up to 3 feet
Discrimination Modes	All Metal, Discrimination, Pinpoint, and Tone Mode
Sensitivity Control	Adjustable with 10 levels
Detection Coil Size	7.5 inches waterproof search coil
Audio Feedback	Variable tone for different metal types
Visual Display	LCD screen with target ID, depth indicator, and battery level
Power Source	2 x 9V batteries (not included)
Battery Life	Approximately 20 hours of continuous use
Weight	2.5 lbs (1.13 kg)
Dimensions (Collapsed)	45 inches (114 cm) length
Dimensions (Extended)	52 inches (132 cm) length
Material	Lightweight ABS plastic with metal shaft
Waterproof	Coil is waterproof; control box is not submersible
Arm Rest	Adjustable padded arm rest
Warranty	1 year limited warranty
Cleaning	Wipe with damp cloth; do not use solvents or submerge
Safety Precautions	Do not sweep near overhead power lines; avoid wet conditions for control box
Spare Parts	Search coil, shaft, and arm rest available as accessories

Frequently Asked Questions - PMD24 Pyle

How do I assemble the Pyle PMD24 metal detector?

To assemble, attach the search coil to the lower shaft using the provided knobs, then extend the telescopic shaft to your desired length and tighten. Connect the coil cable to the control box, and secure the arm rest. Insert two 9V batteries to power on.

What type of batteries does the PMD24 use?

The PMD24 uses two 9V batteries (alkaline recommended). They are not included and should be inserted into the battery compartment located on the control box.

How do I adjust the sensitivity?

Use the sensitivity knob on the control box. Turn clockwise to increase sensitivity for deeper detection, or counterclockwise to reduce interference from mineralized soil. Start at a medium setting and adjust as needed.

What does the discrimination mode do?

Discrimination mode filters out unwanted metals like iron and foil. You can set the discrimination level to ignore certain target types. The detector will emit different tones or display IDs to help identify the metal.

Is the search coil waterproof?

Yes, the 7.5-inch search coil is waterproof and can be submerged in fresh water. However, the control box is not waterproof and should be kept dry at all times.

Why does my PMD24 beep constantly or give false signals?

False signals can be caused by high sensitivity, electromagnetic interference, or mineralized ground. Try reducing the sensitivity, moving away from power lines or electronic devices, and ground balancing if possible. Sweep slowly and keep the coil parallel to the ground.

How deep can the PMD24 detect?

The detection depth depends on the size and composition of the object. For a coin-sized object, the maximum depth is about 6 inches. Larger objects like a metal pipe can be detected up to 3 feet deep under ideal conditions.

How do I clean and maintain the PMD24?

After use, wipe the shaft and control box with a damp cloth. Rinse the search coil with fresh water if used in saltwater or mud. Do not use harsh chemicals or submerge the control box. Store in a dry place.

What do the different tones indicate?

The PMD24 uses three tones: low tone for iron and steel, medium tone for foil and small metals, and high tone for silver and copper. The LCD also shows a target ID number from 0-99 for more precise identification.

Can I replace the search coil or other parts?

Yes, the search coil, shaft, and arm rest are replaceable. Contact Pyle customer support or check online for compatible accessories. The control box is not user-serviceable; contact service for repairs.

USER MANUAL PMD24 Pyle

The Pyle PMD24 uses electronic signals to locate the exact position of studs, ceiling joists, AC wires, and metal through drywall, concrete and other common wall materials. Once the edge of a stud has been detected, the unit emits audio and visual signals (LED Display) that allow you to easily pinpoint its center position.

PMD24 offers quick calibration and heavy-duty ABS construction. The ergonomically designed shape increases user comfort and safety during use.

OPERATING INSTRUCTIONS

1. RED LED
2. GREEN LED
3. FUNCTION SWITCH:

STUD

METAL

VOLTAGE

1. ON/OFF BUTTON
2. STUD ADJUSTMENT
3. POWER LED
4. METAL/VOLTAGE ADJUSTMENT
5. EDGE GROOVE

Battery:

Open door on back of unit and connect a 9-volt battery to clip. Place battery back into case and put battery door on.

Calibration:

Calibrate the unit on the surface being tested before scanning. Unless it is known that No live AC wires are present, detect the AC wires first.

Calibration & Detection for Wood:

Press the ON/OFF button, set the function switch to “STUD” position, then adjust the left knob until the first two side green LEDs lights on the bottom turn on, then switch the knob back until the LED lights turn off; the unit is now calibrated for wood. Slowly slide unit horizontally across the wall, right or left. As you begin to approach a stud, the green LEDs will light successively, from bottom to top. When the center two red LEDs are lit and a steady tone sounds, you have located the edge of the stud. Mark this spot. Continue scanning beyond marked spot until target LEDs go out. Slide unit in reverse direction to locate the other edge of stud. Mark this second spot. Middle of stud is centered between the two marks.

Calibration and Detection for Metal:

Press the ON/OFF button, set the switch to "METAL" position, then adjust the left knob until the first two side green LED lights on the bottom turn on, then switch the knob back until the LED lights turn off; the unit is now calibrated for metal. To set the depth sensitivity of the unit, place the sensor over a metal object at the desired depth, turn the unit on, then adjust the left knob until the first two side green LED lights on the bottom turn on, then switch the knob back until the LED lights turn off; the unit will be set to the desired depth. The actual depth will vary with type and size of metal used. Slowly slide unit horizontally across the wall, right or left. As you begin to approach a metal, the green LEDs will light successively, from bottom to top. When the center two red LEDs are lit and a steady tone sounds, you have located the edge of the metal. Mark this spot. Continue scanning beyond the marked spot until target LEDs go out. Slide unit in reverse direction to locate the other edge. Mark this second

spot. The middle of the metal is the center point between the two marks.

When metal sensing is set to maximum depth sensitivity and the sensed metal object is close to the unit (example; metal behind 1/2 inch wallboard) the apparent width of the sensed metal can be very wide. To locate the true metal size, place the unit in the approximate center of the indicated area and re-calibrate the unit. Then re-scan the area. Repeat this procedure until the size of the metal is determined.

Calibration and Detecting live Wires:

“Set the function switch to “VOLTAGE” position, then adjust the right knob until the two red LED lights turn on, then switch the knob back until the LED lights turn off. The unit is now calibrated for voltage. Its AC voltage sensing is set to Maximum sensitivity. Slowly slide unit horizontally across the wall, right or left. When the center two red LEDs flash and the tone sounds continuously, you have located the AC line. Reduce the sensitivity by turning back the knob. Then re-scan to get an accurate location of the AC line.”

To be safe, detect the AC live wires first unless it is known that no live AC lines are present.

WARNING

Shielded wires or live wires in metal conduits, casings, metalized walls or thick, dense walls will not be detected. Always turn AC power off when working near wiring.

PMD24 is designed to detect 110 and 220 volts AC in live electrical wires. It will also detect the presence of live wires greater than 220 volts.

CAUTION

You should always use caution when nailing, cutting or drilling in walls, ceilings and floors that may contain wiring or pipes near the surface. Shielded, dead, telephone, TV cable or non-powered wiring will not be detected as live wires. Always remember that studs or joists are normally spaced 16 inches or 24 inches apart and are typically 1^1/2 inches in width. To avoid surprises, be aware that anything closer together or of a different width may be an additional stud, ceiling joist, pipe or fire break. When working near AC electrical wires, always turn off the power.

Prevent Interference

To ensure best performance from the PMD24, the unit should be held properly with the hand on the lower portion of the unit. Keep your free hand at least 6 inches away from the unit while testing or scanning surfaces.

Conventional Construction

Doors and windows are commonly constructed with additional studs and headers for added stability. PMD24 detects the edge of these double studs and solid headers and emits and holds an audio signal as it crosses them.

Surface Differences

Wallpaper - There will be no difference in the function of PMD24 on surfaces covered with wallpaper or fabric unless the covering used contains metallic foil or fibers.

Concrete - Metal up to 3/4 inches deep can be detected. If surface is rough, use of a piece of cardboard as outlined under Ceilings is recommended.

Ceilings - When dealing with a rough surface such as a sprayed ceiling utilize a piece of cardboard when scanning the surface. Run through the calibration technique described earlier WITH the piece of cardboard in place to assure best performance of the unit. Also, it is particularly important in this application to remember to keep your free hand away from the unit.

Specifications

Utilizing the procedure of scanning and marking from two sides, PMD24 will find the center of wood or metal studs or live wires through 3/4 inch surfaces within 1/8 inch accuracy.

Battery Life: 1 year with normal use

Water Resistance: Water resistant, but not waterproof.

Operating Temperature: -20°F to +120°F (-7°C to +49°C)

Storage Temperature: -20°F to +150°F (-29°C to +66°C)

Dimension: (L×W×H): 8.730* 3.6 * 1.8 (in.)

Weight (with battery): 250g (0.11 LBS)