ES-SWLT2 - Razor PANASONIC - Free user manual and instructions

Product Type	Rechargeable Wet/Dry Shaver
Model Number	ES-SWLT2
Brand	Panasonic
Power Source	AC adaptor (RE7-87), automatic voltage conversion
Motor Voltage	3.6 V DC
Charging Time	Approx. 1 hour
Quick Charge	3-minute charge for one shave
Usage Time (full charge)	Approx. 2 weeks (based on 3-minute dry shave daily)
Battery Type	Built-in rechargeable lithium-ion (3-year life)
Shaving System	System outer foil and inner blades
Wet/Dry Use	Yes, suitable for shower and wet shaving with lather
Shaving Sensor	Yes, automatic power adjustment based on beard thickness
Trimmer	Pop-up trimmer for sideburns and long hairs
Shaving Foam Mode	Yes, for making foam from facial cleanser
Switch Lock	Yes, with indicator lamp
Charging Indicator	Red charge status lamp: glows during charge, off when full, blinks for abnormal
Low Battery Warning	Lamp blinks once every second, beeps twice after switch off
Cleaning	Waterproof; rinse under running water with cleaning shutter, use brush
Lubrication	Apply one drop of oil to each outer foil and trimmer after cleaning
Replacement Parts	Outer foil (WES9087) and inner blades (WES9068) set (WES9013)
Outer Foil Life	Approx. 1 year
Inner Blade Life	Approx. 2 years
Accessories	Cleaning brush, oil, protective cap

Frequently Asked Questions - ES-SWLT2 PANASONIC

Will the battery deteriorate if not used for an extended period of time?

Yes, the battery will deteriorate if not used for over 6 months. Perform a full charge at least once every 6 months.

Can I charge the shaver after every use?

Yes, the lithium-ion battery has no memory effect, so charging after every use does not affect battery life.

Why should the adaptor be disconnected after charging?

For safety and to save energy. Charging longer than 1 hour does not affect performance, but disconnecting is recommended.

What is the constituent of the dedicated oil?

The oil is made of liquid paraffin.

Why does the appliance beep twice after switched off?

It indicates that the battery capacity is low. Please recharge the appliance.

How often should I replace the outer foil and inner blades?

Replace the system outer foil approximately every year and the inner blades every two years for optimal performance.

Can I use the shaver in the shower?

Yes, the shaver is waterproof and can be used in the shower. It is designed for wet shaving with lather.

How should I clean the shaver?

Rinse the shaver under running water with the cleaning shutter open, shake off water, and dry. Use the cleaning brush for heavy dirt. Always apply oil after cleaning.

What shaving agents are recommended?

Use shaving foam, gel (without scrubbing compounds), facial cleansing foam (without scrubbing), or liquid body soap. Do not use shaving cream or soap with scrubbing.

Why does the shaving sensor not respond sometimes?

The sensor may not respond with thick beard, low oil, low battery, or depending on shaving gel type. This is normal and not a malfunction.

USER MANUAL ES-SWLT2 PANASONIC

Operating Instructions

O V I 7 K 1 V I 7 1 V 7 D I 1 D V N

(Household use) Rechargeable Shaver

CEONMEON7 ONMO 7VIEK70VIKEJM NEKYM7

Model No. ES-SWLT2

ENOK-NA, "OW NACO7

English....3

VIA DYNNE

Español.... 25

VYNDKAN

Panasonic®

Operating Instructions (Household use) Rechargeable Shaver Model No. ES-SWLT2

Contents

Safety precautions...... 5

Important information....9

Parts identification....10

Preparation....10

How to use ......12

Cleaning the shaver .....15

Replacing the system outer foil and the inner blades....17

FAQ....18

Troubleshooting 19

Battery life....22

Removing the built-in rechargeable battery 22

Specifications 23

Thank you for purchasing this Panasonic product.

Before operating this unit, please read these instructions completely and save them for future use.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions are required to always be followed, including the following:

Read all instructions before using this appliance.

DANGER To reduce the risk of electric shock:

1. Except when charging, always unplug this appliance from the electrical outlet immediately after using.
2. Unplug this appliance before cleaning.

WARNING To reduce the risk of burns, fire, electric shock, or injury to persons:

1. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

1. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

2. Never operate this appliance when it has a damaged cord or plug, when it is not working properly, after it has been dropped or damaged, or after it has been dropped into water. Return the appliance to a service center for examination and repair.

3. Keep the cord away from heated surfaces.
4. Never drop or insert any object into any opening.
5. Do not use outdoors or operate where aerosol (spray) products are being used.
6. Do not use this appliance with damaged shaving blades and/or foil, as it has the potential to result in facial injury.
7. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to "off" then remove plug from outlet.

SAVE THESE INSTRUCTIONS

Safety precautions

Make sure to follow these instructions.

To prevent accidents, injuries or damage to property, please follow the instructions below.

■ The following chart indicates the degree of damage caused by improper operation.

⚠️ DANGER	Indicates a potential hazard that will result in serious injury or death.
⚠️ WARNING	Indicates a potential hazard that could result in serious injury or death.
⚠️ CAUTION	Indicates a potential hazard that could result in minor injury or property damage.

The symbols are classified and explained as follows.

This symbol indicates prohibition.

This symbol indicates requirement that must be followed.

WARNING

▶ This product

This product has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, leave, or store in a high temperature environment.

- Doing so may cause overheating, ignition, or explosion.

Do not modify or repair.

- Doing so may cause fire, electric shock, or injury. Contact an authorized service center for repair (replacement of battery etc).

Never disassemble except when disposing of the product.

- Doing so may cause fire, electric shock, or injury.

▶ In case of an abnormality or malfunction Immediately stop using and remove the AC adaptor.

- Failure to do so may cause fire, electric shock, or injury.

•The main unit, adaptor or cord is deformed or abnormally hot.

- The main unit, adaptor or cord smells of burning. - There is an abnormal sound during use or charging of the main unit.

- Immediately request inspection or repair at an authorized service center.

WARNING

▶ Power supply

Do not connect or disconnect the adaptor to a household outlet with a wet hand.

- Doing so may cause electric shock or injury.

Do not immerse the AC adaptor in water or wash with water.

Do not place the AC adaptor over or near water filled sink or bathtub.

Never use the appliance if the AC adaptor is damaged or if the power plug fits loosely in a household outlet.

Do not damage the cord or the power plug.

- Do not deface, modify, forcefully bend or pull the cord or the power plug. Also, do not place anything heavy on, twist or pinch the cord.

- Doing so may cause electric shock or fire due to a short circuit.

Do not use in a way that would exceed the rating of the household outlet or the wiring.

- Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating.

Use only the supplied AC adaptor with this product.

Do not use the AC adaptor with any other product. (See page 10.)

- Failure to do so may cause burn or fire due to a short circuit.

Fully insert the power plug.

- Failure to do so may cause fire or electric shock.

Disconnect the AC adaptor when cleaning the main body with water.

-Failure to do so may cause electric shock or injury.

Regularly clean the power plug and the appliance plug to prevent dust from accumulating.

- Failure to do so may cause fire due to insulation failure caused by humidity.

▶ Preventing accidents

Do not place within reach of children or infants. Do not let them use it.

- Putting parts or accessories in the mouth may cause an accident or injury.

If oil is consumed accidentally, do not induce vomiting, drink a large amount of water and contact a physician.

If oil comes into contact with eyes, wash immediately and thoroughly with running water and contact a physician.

- Failure to follow these instructions may result in physical problems.

WARNING

▶ Note the following precautions

The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.

- Failure to do so may cause an accident or injury.

CAUTION

▶ Protecting the skin

Do not use excessive pressure to apply the system outer foil to your lip or other part of your face.

Do not apply the system outer foil directly to blemishes or injured skin.

Do not touch the blade section (metallic section) of the inner blade.

- Doing so may cause injury to skin or hand.

Do not forcefully press the system outer foil. Also, do not touch the system outer foil with fingers or nails when in use.

Do not use this product for hair on head or any other part of the body.

- Doing so may cause injury to skin or reduce the life of the system outer foil.

Check the system outer foil for cracks or deformations before use.

- Failure to do so may cause injury to the skin.

▶ Note the following precautions

Do not allow metal objects or trash to adhere to the power plug or the appliance plug.

- Doing so may cause electric shock or fire due to a short circuit.

Do not share your shaver with your family or other people.

- Doing so may result in infection or inflammation.

Disconnect the adaptor from the household outlet when not charging.

- Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.

Handling of the removed battery when disposing

DANGER

•The rechargeable battery is exclusively for use with this appliance. Do not use the battery with other products.

- Do not charge the battery after it has been removed from the product.

- Do not throw into fire or apply heat.

- Do not hit, disassemble, modify, or puncture with a nail.

- Do not let the positive and negative terminals of the battery get in contact with each other through metallic objects.

- Do not carry or store the battery together with metallic jewellery such as necklaces and hairpins.

- Do not use or leave the battery where it will be exposed to high temperatures, such as under direct sunlight or near other sources of heat.

• Never peel off the tube.

- Doing so may cause overheating, ignition, or explosion.

WARNING

After removing the rechargeable battery, do not keep it within reach of children and infants.

- The battery will harm the body if accidentally swallowed.

If this happens, consult a physician immediately.

If the battery fluid leaks out and comes in contact with the eyes, do not rub the eyes, and thoroughly rinse with clean water, such as tap water.

- Failure to do so may cause eye injury.

Consult a physician immediately.

CAUTION

If the battery fluid leaks out and comes in contact with the skin or clothes, rinse off with clean water, such as tap water.

- Failure to do so may cause inflammation.

Important information

- This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean with water. The following symbol means suitable for use in a bath or shower.

- Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method. - Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged. - If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time. - The following symbol indicates that a specific detachable power supply unit is required for connecting the electrical appliance to the supply mains. The type reference of power supply unit is marked near the symbol.

- Charge the appliance correctly according to these Operating Instructions. (See page 10 "Charging the shaver".) - This appliance contains battery that is only replaceable by skilled persons. Please contact an authorized service center for the details of repair.

Note the following precautions

▶ When using

- Do not bring the system outer foil into contact with hard objects.

Doing so may damage the system outer foil as it is very thin and deforms easily.

- Do not drop or hit against other objects.

Doing so may cause injury.

▶ When storing

- Store the shaver in a place with low humidity after use.

Failure to do so may cause malfunction due to condensation or rust.

- Be sure to place the protective cap on the shaver when carrying around or storing.

Failure to do so may cause injury to skin or reduce the life of the system outer foil.

▶ When cleaning

- Do not dry using heat from a dryer or other appliance. Doing so may cause malfunction or deformation of the parts.

- Do not leave the shaver exposed to direct sunlight with the foil frame detached.

Doing so may deteriorate the waterproof rubber and degrade waterproof function, which may cause to malfunction.

Parts identification

A

B

©

D

A Main body

① Protective cap
② System outer foil
③Water inlets
④Cleaning shutter
⑤ Foil frame release buttons
⑥ Thumb rest
⑦Power switch

To turn the shaver on and off and also lock and unlock the power switch.

⑧ Switch lock lamp (🔒)

⑨ Charge status lamp (→)
⑩Appliance socket
⑪ Foil frame
⑫ System outer foil release buttons
⑬ Outer foil section
⑭Inner blades
⑮ Trimmer
⑯ Trimmer handle

B AC adaptor (RE7-87)

⑰Adaptor
⑱Power plug
⑲ Cord
⑳Appliance plug

Accessories

© Cleaning brush
D Oil

Preparation

Charging the shaver

• Turn the shaver off.
• Wipe off any water droplets on the appliance socket.

1 Insert the appliance plug into the shaver.

2 Plug in the adaptor into a household outlet.

• Check that the charge status lamp (→) is glowing.
• Charging is completed after approx. 1 hour.
• If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration.

3 Disconnect the adaptor after charging is completed and the charge status lamp (→) turns off.

Note

You cannot operate the shaver while charging.

Quick charge

Even though the battery runs out, you can shave once after 3-minute charge. (This will differ depending on usage.)

While charging

The charge status lamp (→) glows red.

After charging is completed

The charge status lamp (→turns off.

Abnormal charging

The charge status lamp (→) will blink twice every second.

- After charging is completed, turning the power switch ON with the shaver plugged in will cause the charge status lamp (→) to light up and then turn off after 5 seconds.

This shows that the shaver is fully charged.

- When charging the shaver for the first time or when it has not been in use for more than 6 months, the charging time may change or the charge status lamp (▶) may not glow for a few minutes. It will eventually glow if kept connected.

- Recommended ambient temperature for charging is 10^ - 35^ (50°F - 95°F). It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures.

The charge status lamp (▶) will blink twice every second when there is a problem with charging. Charge the shaver within the recommended ambient temperature range.

- The shaver can be used for approximately 2 weeks with a full charge. (Based on one 3-minute dry-shave usages per day in an ambient temperature range of 20^ - 30^ [68 °F - 86 °F].)

The number of usable days varies depending on the following conditions.

- Beard thickness

- Pressure applied to the skin

- Usage of wet shaving

- Usage in shaving foam mode

- If there is noise from the radio or other sources while using or charging the appliance, move to a different location to use the appliance.

How to use

▶ Usable facial cleansers, etc.

		Shaving	Shaving foam mode
Shaving agent	Shaving foam —	√
	Shaving gel	√	✕
	Shaving cream	✕	✕
Facial cleanser	Facial cleansing foam (without scrubbing compounds)	√	√
	Facial cleansing foam (with scrubbing compounds)	✕	✕
	Facial soap	√	✕
Body soap etc.	Liquid	√	√
	Foam —	√

- Do not use anything other than above listed shaving agent/facial cleanser/body soap etc. as these may cause the blades to clog, or be unable to make foam.

Making foam in shaving foam mode

It is easier to make foam this way than by hand.

1 Take an appropriate amount of facial cleanser etc. in the palm of your hand.

2 Add an appropriate amount of water or hot water.

3 Check that the cleaning shutter is closed and hold the power switch for 2 seconds or more to switch to shaving foam mode.

The switch lock lamp ( 🔊 and charge status lamp ( ➤) blink alternately.

• The shaving foam mode ends after 15 seconds. The shaver can then be used to shave.
• To stop using the shaving foam mode and start shaving, press the power switch once.

- When the switch lock lamp() blinks after the power switch is pressed, the shaver will not operate as it is locked. Hold the power switch for more than 2 seconds to unlock. (See page 15.)

4 Press the blades gently in the palm of your hand, mix the facial cleanser etc. around and move the blades up and down to make foam.

- If there is insufficient foam, add slightly more water, hot water or facial cleanser etc. to make it easier to create foam.

Line drawing of a hand holding a small object, possibly a tool or device, with no visible text or symbols.

Notes

- Do not use shaving agent (excluding foam), facial cleansing foam (with scrubbing compounds) or soap as these may cause the blades to clog, or be unable to make foam.

Shaving beard

- Before shaving, check that the cleaning shutter is closed.

1 Press and shave.

- The “shaving sensor”, which automatically adjusts the power depending on the beard thickness, will operate. It will shave with high power on areas where the beard is heavy, and reduce the power on areas where the beard is thin, to reduce burden on the skin.

Line drawing of a hand holding a flashlight (no text or symbols)

Tips for better shaving

Apply the whole system outer foil perpendicularly against the skin and shave by slowly gliding the shaver over the face against the grain of the beard.

• The beard under the chin and around the throat can be shaved better by stretching the skin so the beard will stand.
  • To prevent damaging the system outer foil, do not shave with only a part of the system outer foil.

2 Press when finished.

When the battery capacity is low

The charge status lamp (→) blinks once every second when operating the shaver. The appliance beeps twice after switched off.

- You can shave 2 to 3 times after the charge status lamp (→) blinks. (This will differ depending on usage.)

▶ Using the trimmer

Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns.

▶ Tips for better usage

Apply the trimmer edge perpendicular to skin gently and move downward slowly.

Trimming sideburns Pre-shave of long beards

Illustration showing two-step facial massage technique: one with finger placement and arrow, the other with tool and motion arrows (no text or symbols)

Notes

• After wet shaving, wash the main body with water and apply oil to the system outer foil.
- Depending on the beard thickness or the amount of beard trimmings in the shaver head, the shaving sensor may not react and the driving sound may not change. This is not abnormal.
- The shaving sensor may not respond depending on the type and quantity of the shaving gel or the quantity of the foam. This is not abnormal.
• The appliance may not operate in an ambient temperature lower than approximately 5 °C (41 °F).
- To prevent erroneous operation, place your fingers on the thumb rest while using the shaver.

Operation and display of the switch lock

▶ Locking the power switch

1. Press once and then release.

• The shaver starts operating.

1. Hold ⓐ for more than

2 seconds.

• The switch lock lamp

( 🔒 ) will light up for

5 seconds and turn off.

• The shaver will stop operating.

1. Release

▶ Unlocking the power switch

1. Hold for more than 2 seconds.

- The switch lock lamp (🔒) will turn off.

1. Once the shaver starts operating, release Ⓞ.

- The power switch is locked when the switch lock lamp (💡) blinks for 5 seconds and the shaver does not operate even though the power switch is pressed.

Cleaning the shaver

We recommend cleaning the shaver after each use.

Cleaning with water

- Turn the shaver off and disconnect the AC adaptor.

1. With the cleaning shutter closed, apply some hand soap and some water to the system outer foil.

2. Turn the shaver on and make foam for a few seconds.

There are two ways to clean the shaver, depending on the actual dirt level.

To remove light dirt To remove heavy dirt

1. Slide the cleaning shutter until it clicks.

• The water inlets of the shaver head are opened.

1. Pour running water into the water inlets and rinse thoroughly, and then turn off.

• Pour running water into both water inlets.

- Rinse with water and shake up and down several times to remove the water, and then close the cleaning shutter.

1. Turn the shaver off and remove the outer foil section. (See page 17.)

2. Clean the shaver and the outer foil section with running water.

- Rinse with water and shake up and down several times to remove the water.

1. Wipe off any drops of water with a dry cloth.

2. Dry the outer foil section, the shaver, and the trimmer completely.

3. Allow the shaver to dry in the shade, avoid direct sunlight.

4. Lubricate the shaver.

It will keep the movement of the blade smooth and maintain a comfort shave.

1. Apply one drop of oil to each of the system outer foils.
2. Raise the trimmer and apply a drop of oil.
3. Switch the shaver on, and run it for approximately five seconds.
4. Switch off the shaver, and wipe off any excess oil from the system outer foil with a soft cloth.

Notes

• Do not use any kitchen or bathroom detergents other than hand soap.
  Doing so may cause malfunction.
• Do not wipe with thinners, benzine, alcohol etc. Doing so may cause malfunction, cracking or discoloration of the parts.
• Be careful not to hit the main body on the sink or any other object while draining the water. Failure to do so may cause malfunction.

Cleaning with the brush

Remove the outer foil section and the inner blades. (See this page.) Do not use any brush other than the supplied one.

▶ Cleaning with the long brush

Clean the foil frame, system outer foil, the main body and the trimmer using the long brush.

▶Cleaning with the short brush

• Clean the inner blades using the short brush by moving it in direction as illustrated.
• Do not move the short brush perpendicularly against the blades as it will damage the inner blades and affect their sharpness.

Replacing the system outer foil and the inner blades

system outer foil once every year

inner blades once every two years

▶Removing the outer foil section

Press the foil frame release buttons and lift the outer foil section upwards.

▶ Attaching the outer foil section

After turning the foil frame mark (✗) to the front, securely attach the outer foil section to the shaver until it clicks.

▶ Replacing the system outer foil

1. Press the system outer foil release buttons and pull down the system outer foil.

- Do not press the system outer foil release buttons with excessive force. Doing so may bend the system outer foil, preventing complete attachment to the foil frame.

1. Align the foil frame mark (✗) and the system outer foil mark (△) and securely attach together until it clicks.

▶ Replacing the inner blades

1. Remove the inner blades one at a time.
2. Insert the inner blades one at a time.

▶ Note

Do not throw away the foil frame.

▶ Replacement parts

Replacement parts are available at your dealer or Service Center.

Replacement parts for ES-SWLT2	System outer foil and inner blades	WES9013
	System outer foil	WES9087
	Inner blades	WES9068

FAQ

Question Answer

Will the battery deteriorate if not used for an extended period of time?

Can I charge the shaver after every use?

Why should the adaptor be disconnected after charge?

What is the constituent of the dedicated oil?

Why does the appliance beep twice after switched off?

The battery will deteriorate if not used for over 6 months, so make sure to perform a full charge at least once every 6 months.
The battery used is a lithium-ion, so charging after every use will have no effect on battery life.
Charging the battery for more than 1 hour will not affect battery performance, but disconnect the adaptor for safety and to save energy.
▶ Constituent of the oil is liquid paraffin.
The sound indicates that the battery capacity is running low. Please charge the appliance.

Troubleshooting

Perform the following actions. If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorized by Panasonic for repair.

Problem Action

The power switch does not turn ON.

The power will not switch to OFF.

▶ Unlock the switch lock. (See page 15.)

Press the power switch twice while using in shaving foam mode.

Problem Action

The shaving sensor does not respond.

Depending on the beard thickness or the amount of beard trimmings in the

▶ shaver head, the shaving sensor may not react and the driving sound may not change. This is not abnormal.

The shaving sensor may not respond depending on the type and quantity of the shaving gel. This is not abnormal.

The shaving sensor may not respond when the remaining battery capacity is low. If this happens, recharge the shaver.

Apply oil. (See page 16.) The shaving sensor may not respond when there is not enough oil on the blades.

Problem Action		Problem Action
The shaving sensor responds even though the shaver is not in contact with the skin.	Clean the beard trimmings from the shaver.When the shaver is very dirty, first use the cleaning brush to remove beard trimmings.Or, remove the foil frame and wash with water.(See page 16.)	The shaver cannot be charged.	The recommended temperature for charging is 10 ^ - 35 ^ ( 50 ^ - 95 ^ ). If charged at a temperature other than the recommended temperature, the shaver may take longer to charge or may not charge at all.
	Replace the system outer foil and/or inner blades.Expected life of system outer foil and inner blades:System outer foil:Approximately 1 yearInner blades:Approximately 2 years
Foam cannot be made in shaving foam mode.	Making foam may be difficult depending on the type of facial cleansers etc., so adjust the amount of water or facial cleanser.	Operating time is short even after a full charge.	The shaver can be used for about 2 weeks on a full charge assuming dry-shaving for 3 minutes per day. However, the usable number of days may be reduced depending on how the shaver is used (for example, use in shaving foam mode, wet shaving, or use in low temperatures).
Foam made in shaving foam mode contains shavings.	Before making foam, cleanly rinse off any shavings. (See page 15.)		Apply oil.When the number of operations per charge starts to decrease, the battery is nearing the end of its life.

Problem Action
Shaver does not operate even after charging.	Use the appliance in an ambient temperature approximately 5 °C (41 °F) or higher.
	The battery has reached the end of its life.
	The shaver will not operate with the AC adaptor connected. Please use the shaver after it has been sufficiently charged and the AC adaptor disconnected.
The driving sound changes while shaving.	The shaving sensor is operating. The sound changes depending on the beard thickness.

Problem Action
Makes a loud sound.	Apply oil.The blades will not move smoothly when there is no oil on the blades, requiring more power.
	The shaver makes a high-pitched sound due to the linear motor drive. This does not indicate a problem.
	Confirm that the blades are properly attached.
	Clean the system outer foil with the brush.
The odor is getting stronger.	This can be improved by cleaning every time after shaving.
Shavings fly out in all directions.	This can be improved by cleaning every time after shaving.Clean the inner blades with the brush when shavings are adhering to the inner blades.
	Confirm that the cleaning shutter is firmly closed.

Problem Action

System outer foil gets hot.	Apply oil.
	Replace the system outer foil if it is damaged or deformed. (See page 17.)
You do not get as close a shave as before.	Apply oil.
	This can be improved by cleaning every time after shaving.
	Replace the system outer foil and/or inner blades. Expected life of system outer foil and inner blades: System outer foil: Approximately 1 year Inner blades: Approximately 2 years
The shaver cannot be properly cleaned even after water is poured from the water inlets.	When the shaver is very dirty, first use the cleaning brush to remove beard trimmings. Or, remove the foil frame and wash with water. (See page 16.)

Battery life

The life of the battery is 3 years. The battery in this shaver is not intended to be replaced by consumers.

Removing the built-in rechargeable battery

ATTENTION:

A lithium ion battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

Remove the built-in rechargeable battery before disposing of the shaver.

The battery is to be disposed of safely.

This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction.

- Remove the shaver from the AC adaptor.

- Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.

- Perform steps ① to ⑤ and lift the battery, and then remove it.

• Take care not to short circuit the positive and negative terminals of the removed battery, and insulate the terminals by applying tape to them.

Specifications

Power source	See the name plate on the AC adaptor. (Automatic voltage conversion)
Motor voltage	3.6 V---
Charging time Approx. 1 hour

This product is intended for household use only.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, install and use in accordance with provided instructions. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Personal Care & Beauty Care Products

FOR USA ONLY

30-Day Quality Satisfaction Guarantee

If you are dissatisfied with any Panasonic Personal Care & Beauty Care Products for any reason, simply return it to the place of purchase with a dated proof of purchase, in the original packaging, with all accessories, parts and instructions, within 30 days of the date of purchase for a full refund. Abuse or misapplication of this product voids the guarantee.

PRODUCT REGISTRATION (U.S. customers only)

Go to www.shop.panasonic.com/register and register your product now to receive these benefits:

Safety Notification

We contact our customers in case of recall

Owner Verification

Proof of purchase in case of product theft or loss

Efficient Warranty Service

In case there is a problem with your product

Special Offers and Promotions from Panasonic

FOR YOUR CONVENIENCE, WE HAVE ESTABLISHED A TOLL-FREE (IN USA ONLY) NATIONAL ACCESSORY PURCHASE HOTLINE AT 1-800-332-5368.

Panasonic®

Line drawing of a hand holding a small object, possibly a medical or anatomical device (no text or symbols present)

Notas

Line drawing of a hand holding a flashlight (no text or symbols)

Illustration of a person applying facial contour to the ear area, showing finger placement and eye alignment (no text or symbols)

Notas

Especificaciones

Panasonic Corporation of North America

Two Riverfront Plaza, Newark, NJ 07102-5490

Service • Assistance • Accessories

https://shop.panasonic.com/personal-care

https://shop.panasonic.com/support

https://www.panasonic.com

© Panasonic Corporation 2023

⑤ EN, ES

Printed in Japan

Impreso en Japón

ES9700SWLT21A Y0623-0