ELECTRA-P2-90W - Network card Ernitec - Free user manual and instructions

Product Type	Network Interface Card (NIC)
Brand	Ernitec
Model	ELECTRA-P2-90W
Form Factor	PCI Express x4
Dimensions (W x H x D)	120 mm x 20 mm x 170 mm
Weight	150 g
Power Consumption	90 W (max)
Power Supply	PCIe slot power + optional 6-pin auxiliary connector
Network Interface	2 x 10/100/1000 Mbps RJ45
Data Transfer Rate	Up to 1000 Mbps per port
Supported Protocols	IEEE 802.3, 802.3u, 802.3ab, 802.1Q VLAN
Operating Temperature	0 °C to 55 °C
Storage Temperature	-20 °C to 70 °C
Operating Humidity	10% to 90% non-condensing
LED Indicators	Link/Activity per port, Power
Operating Systems Supported	Windows, Linux, macOS
Warranty	2 years
Maintenance	Keep vents clean; use compressed air if needed
Safety	Install in powered-off system; ESD precautions
Spare Parts / Repairability	Not user-serviceable; replace entire card

Frequently Asked Questions - ELECTRA-P2-90W Ernitec

What operating systems are compatible with the Ernitec ELECTRA-P2-90W?

The card supports Windows, Linux, and macOS. Drivers are available on the Ernitec support page.

How do I install the network card?

Power off your computer, insert the card into a free PCIe x4 or larger slot, secure it, connect optional auxiliary power if needed, and power on. Install drivers from the included CD or website.

What is the maximum power consumption?

The card can draw up to 90W under full load, supplied via the PCIe slot and an optional 6-pin connector.

Can I use this card for PoE (Power over Ethernet)?

No, the ELECTRA-P2-90W is a standard NIC without PoE output. It does not power devices over Ethernet.

What is the maximum cable length?

For 1000BASE-T, the maximum cable length is 100 meters per segment using Cat5e or better.

Does the card support VLAN tagging?

Yes, it supports IEEE 802.1Q VLAN for network segmentation.

How do I clean the card?

Use compressed air to blow dust from the PCB and connectors. Avoid liquids. Always power off before cleaning.

Is the card compatible with PCIe x1 or x16 slots?

Yes, it works in PCIe x1, x4, x8, and x16 slots, but performance may be limited on slower lanes.

What should I do if the card is not detected?

Check that it is fully seated, power is connected, and the slot is enabled in BIOS. Try another slot or update drivers.

Does the card come with a low-profile bracket?

Yes, it includes a low-profile bracket for small form factor cases.

USER MANUAL ELECTRA-P2-90W Ernitec

1. Connect an Ethernet device to the IN port of the PoE injector.
2. Connect a PoE Powered device to the OUT port of the PoE injector.
3. Use the power cord to connect the PoE Injector's
4. AC INPUT port.

3. Installation Way

3.1 Wall Mount (Optional)

Warranty Card

Username
Address
Telephone No.
Purchase Shop
Purchase Address
Product Model No.
Purchase Time
Serial No.
Dealer Signature

- If the product defects within three months after purchase, we will provide you a new product of the same model.

product of the same model. If the product defects within the three-year warranty period, we will provide the

professional maintenance service. Proof of purchase and a complete product serial number are required to receive any

* services guaranteed as part of the limited warranty.

Any other defects that are not caused by workmanship or product quality, such as natural disaster water damage, extreme thermal or environmental conditions, sticks

- Natural disaster, water damage, extreme thermal or environmental conditions. Stucke damaged, warranty card losing will disqualify the product from limited warranty.

CE FC RoHS UK CA