HighRise - DJ Equipment SAMSON - Free user manual and instructions

Product Type	DJ Headphones
Brand	Samson
Model	HighRise
Driver Size	40 mm
Frequency Response	20 Hz – 20 kHz
Impedance	32 ohms
Sensitivity	100 dB SPL/mW
Maximum Input Power	500 mW
Connector	3.5 mm stereo jack (1/8") with 1/4" adapter
Cable Length	1.5 m (coiled, extends to 3 m)
Weight	250 g
Dimensions (folded)	180 x 170 x 80 mm
Ear Cup Design	Closed-back, over-ear
Headband	Adjustable, padded
Swivel Mechanism	90° rotating ear cups for single-ear monitoring
Color	Black
Included Accessories	1/4" adapter, carrying pouch
Power Source	Passive (no battery required)
Cleaning	Wipe with a soft, dry cloth; do not use liquids
Storage	Store in a cool, dry place; avoid extreme temperatures
Safety	Protect hearing by avoiding prolonged exposure to high volume
Spare Parts & Repairability	Ear pads and cable replaceable; other repairs by authorized service
Certification	CE, RoHS

Frequently Asked Questions - HighRise SAMSON

Are the Samson HighRise DJ headphones compatible with smartphones?

Yes, they have a 3.5 mm jack that works with most smartphones, tablets, and laptops. An included 1/4" adapter allows use with DJ mixers and audio interfaces.

How do I clean the ear pads of the HighRise headphones?

Wipe the ear pads gently with a soft, dry cloth. Do not use water or cleaning liquids as they may damage the padding. For deep cleaning, replaceable ear pads are available.

Can I use only one ear cup for monitoring?

Yes, the ear cups swivel 90 degrees, allowing you to rotate one ear cup backward for single-ear monitoring while keeping the other over your ear.

What is the maximum volume these headphones can handle?

The maximum input power is 500 mW. However, to protect your hearing, it is recommended to keep the volume at moderate levels and avoid extended listening at high volumes.

Are replacement parts available for the HighRise?

Yes, replacement ear pads and cables are available separately. For other repairs, it is best to contact Samson customer support or an authorized service center.

The sound is distorted; what should I check?

First, ensure the audio source is not clipping. Then check the cable connection and try a different device. If distortion persists, the driver may be damaged; contact support.

How long is the cable on the HighRise headphones?

The cable is coiled and measures 1.5 m when relaxed, but it can extend up to 3 m for added mobility.

Do the Samson HighRise headphones have a microphone?

No, the HighRise is a dedicated monitoring headphone without a built-in microphone. It is designed for critical listening and DJ monitoring.

Can I store the headphones in the included pouch?

Yes, the headphones fold flat and fit into the included carrying pouch for easy storage and transport. Avoid placing heavy objects on top of the pouch.

What is the warranty period for Samson HighRise headphones?

Samson typically offers a one-year limited warranty against defects in materials and workmanship. Check your local dealer or Samson's website for specific warranty terms.

USER MANUAL HighRise SAMSON

HighRise Mono Active Mic Booster

Owner's Manual

SAMSON®

Follow us:

@samson

@samson_technologies @samsontech

Samson Technologies Corp.

Copyright 2022, v1.2

278-B Duffy Ave

Hicksville, NY 11801

www.samsontech.com

Description

HighRise is a microphone preamp that will boost low output mics by adding up to +30dB of clean gain. This will allow any dynamic mic or ribbon mic to be used with different types of mixers, preamps, and digital audio interfaces. Additionally the HighRise will improve the EIN (equivalent input noise) specification of the mic preamps you plug it into.

NOTE - HighRise requires phantom power to operate

With proper care and maintenance your HighRise will operate trouble-free for many years. Should your HighRise ever require servicing a Return Authorization (RA) number must be obtained before shipping your unit to Samson. Without this number the unit will not be accepted. Please email [e-mail] for an RA number prior to shipping your unit. If your direct box was purchased outside of the United States, contact your local distributor for warranty details and service information.

graph TD
    A["Input Data"] --> B["Sensor"]
    B --> C["HighRIS"]
    C --> D["Output Sensor"]
    D --> E["Microphone"]

Callouts

1. INPUT – XLR input connector for connecting dynamic mics or ribbon mics to mixers, low gain pre-amps or digital audio interfaces that have a gain range that is too small.
2. OUTPUT – XLR output connector for passing the input signal through to your mixer, preamp, or digital audio interface.
3. LOW CUT – When the switch is set to 120Hz, HighRise will cut frequencies beginning at 120Hz. This helps remove unwanted bass frequencies known to cause audio signals/recordings to sound muddy.
4. BOOST – Change this 3 position switch to best suit your use case. HighRise adds 20dB of gain, 30dB of gain, or 20dB of gain with HF Lift (more treble).
5. PWR LED – White LED indicates that the HighRise is operational, powered by mixer phantom power.

Setup

The HighRise can be quite useful on stage or in the studio for connecting low gain audio sources to mixers, preamps, or digital audio interfaces. By utilizing the HighRise, the signal's gain can be boosted cleanly thus increasing audio level without adding noise. The following diagram shows a typical hook-up using a dynamic microphone connected to a professional style multi-channel audio mixer.

graph LR
    A["Device 1"] --> B["HIGHRISE"]
    B --> C["External Voice"]

• Engage phantom power on your mixer or digital audio interface.
• Set the volume controls of your audio system/mixer or DAW/interface to the off (minimum) position.
• Connect your mic to the HighRise INPUT jack.
• Connect the XLR OUTPUT to the XLR/MIC input of a mixer or other audio device.
• Raise the level of the audio system to the appropriate level.
• Change position of LOW CUT and BOOST switches to suit your specific use case.

Specifications

Type Class-A biased bipolar transistors, fully differential input/output

Amplification +20dB low-rise, +30dB high-rise

Frequency Response -1dB @ <10Hz low-rise, -1.5dB @ 20Hz high-rise

Input impedance 3k low-rise, 2.1k high-rise

Power Supply P12-P48 phantom power

Connectors XLR, balanced (Input)

XLR, balanced (Output)

Construction 14-gauge steel chassis

Dimensions 4.25" x 2.25" x 1.755"

110mm x 54mm x 46mm

Weight0.7lb

0.32kg

Support

Having Trouble with your HighRise?

We can help!

CONTACT OUR SUPPORT TEAM: [e-mail]

Our experts can help you resolve any issues.

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private household in the 27 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).

For Countries not mentioned above, please contact your local authorities for a correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Samson Technologies Corp.

278-B Duffy Ave

Hicksville, NY 11801

www.samsontech.com