IOD200 - Ice cream maker Ice-O-Matic - Free user manual and instructions

Product Type	Ice Cream Maker (Batch Freezer)
Brand	Ice-O-Matic
Model	IOD200
Dimensions (W x D x H)	Approximately 22 x 28 x 36 inches
Weight	Approximately 175 lbs
Power Supply	115V / 60Hz / 1-Phase
Amperage	15 A
Refrigerant	R404A
Capacity	2.0 quarts per batch
Freezing Cylinder Material	Stainless steel
Controls	Digital timer and temperature control
Dashpot	Adjustable dasher speed
Compressor Type	Air-cooled hermetic
Functions	Freeze, Hardening, Cleaning cycle
Cleaning	Manual cleaning with approved sanitizer; removable dasher and lid
Safety Features	Overload protection, safety switch on lid, compressor delay
Spare Parts Availability	Through authorized Ice-O-Matic distributors
Warranty	1 year parts and labor
Certifications	NSF, cULus
Noise Level	< 70 dB
Usage	Commercial countertop

Frequently Asked Questions - IOD200 Ice-O-Matic

How do I clean the Ice-O-Matic IOD200?

Disconnect power, remove dasher and lid, wash all removable parts with warm soapy water, rinse, and sanitize with an approved sanitizer. Wipe down the freezing cylinder with a soft cloth. Reassemble and run a cleaning cycle if available.

What is the maximum batch size for the IOD200?

The IOD200 can produce up to 2 quarts of ice cream per batch, depending on the mix composition and desired overrun.

How long does it take to freeze a batch?

Freezing time typically ranges from 10 to 15 minutes for a standard 2-quart batch, depending on mix temperature and recipe.

What type of power supply is required?

The IOD200 requires a 115V / 60Hz single-phase electrical connection with a 15-amp dedicated circuit.

Can I use the IOD200 for soft serve?

The IOD200 is designed for hard ice cream. For soft serve, a different machine with a continuous freeze function is recommended.

Why is my ice cream not freezing properly?

Check that the mix is pre-chilled (<40°F), the dasher is properly inserted, the lid is closed, and the refrigerant charge is adequate. Also ensure the ambient temperature is not too high.

How often should I replace the dasher seal?

Inspect the dasher seal regularly for wear or cracking. Replace it annually or sooner if leaking occurs to maintain hygiene and performance.

What safety features does the IOD200 have?

The machine includes an overload protector, a safety switch that stops operation when the lid is opened, and a compressor delay to prevent short cycling.

Where can I find spare parts for the IOD200?

Spare parts are available through authorized Ice-O-Matic distributors or by contacting Ice-O-Matic customer service. Always use genuine parts for warranty and safety.

What is the warranty coverage?

The IOD200 comes with a 1-year parts and labor warranty from the date of purchase. Extended warranties may be available through dealers.

USER MANUAL IOD200 Ice-O-Matic

Ice. Pure and Simple

SERVICE PARTS MANUAL

ICE ONLY DISPENSERS

MODELS-IOD150, IOD200 AND IOD250

14-1010

Date 6/13/16

IOD150, IOD200, IOD250 Dispenser

This parts list contains the service parts available for the IOD150-200-250 dispensers

Check the model number on the data plate and refer to the correct listing for the specific component.

Check carefully that the correct part is identified and ordered.

Note: Part Numbers in BOLD are not stocked items

Table of Contents Page 1

Cabinet and Dispenser Part Numbers, IOD150 Page 2 - 3

Cabinet and Dispenser Part Numbers, IOD200 and IOD250 Page 4 - 5

Rotary Solenoid Page 6

Electrical Box, IOD150 Page 7

Electrical Box, IOD200 and IOD250 Page 8

Wiring Diagram Page 9

Ice-O-Matic

11100 East 45th Ave.

Denver Co. 80239

IOD150, IOD200 and IOD250 Service Parts

IOD 150 Cabinet and Dispenser

IOD150, IOD200 and IOD250 Service Parts IOD 150 Cabinet and Dispenser

Item Item

No. Part No. Description No. Part No. Description

1 1011342-12 Gate Slide 34 1011342-07 Baffle
2 1011342-144 Gate Restrictor 35 1011342-62 Plug
3 1011342-145 Plate, Motor Mounting 36 1011342-63 Clip, White
4 1011342-06 Agitator Assy 37 1011342-76 Hex Nut, No. 10-32
5 1011342-18 Cover, Rear Wrapper 38 1011342-77 Hex Nut, No. 10-32, Nyloc
6 1011342-141 Lower Panel (F/Drip Tray) 39 1011342-78 Hex Nut, 1/4-20
7 1011342-05 Extension Assy, Drip Tray 40 1011342-79 Washer, .255 I.D.
8 1011342-17 Wrapper (ED 150) 41 1011342-81 Washer, No. 10, .219 I.D.
9 1011342-13 Retainer, Lever, Ice Dispense 42 1011342-83 Washer, .218 I.D.

10 1011342-02 Pin, Drip Tray Mounting

11 1011342-29 Boot, Switch

12 1011342-49 Snap Bushing

13 1011342-03 Retainer, Agitator

14 1011342-25 Agitator Motor Heater, 120 V

15 1011342-26 Dispense Switch

16 1011342-133 Agitator Motor, 120 Volt

17 1011342-38 Solenoid Assembly, 120 Volt

18 1011342-128 Electrical Box Ass'y, 120 V

19 1011342-16 Bracket, Motor Mounting

20 1011342-103 Washer, Captivating No. 8

21 1011342-115 Hinge, Gusset

22 1011342-53 Seal, Agitator Motor Shaft

23 1011342-01 Gasket, Gate 56 1011342-63 Clip, Black

*24 1011342-55 Plug (120 Volt Models Only)

25 1011342-57 Gasket, Motor Shaft

26 1011342-139 Ice Chute

27 1011342-69 Cover, Ice Chute

28 1011342-73 Agitator Disk

29 1011342-11 Merchandiser, S.S. (IOD 150) 62 1011342-150 Cup Rest

29 1011342-64 Merchandiser, Black (IOD 150)

30 1011342-58 Panel, Plexiglass, Inner

31 1011342-72 Drip Tray, Black, Insulated

32 1011342-68 Lid, Dispenser, Black

33 1011342-56 Hopper Assy., Foamed

43 1011342-85 Hex Nut, No. 8-32

44 1011342-86 Insert, Threaded, No. 8-32

45 1011342-89 Machine Screw, Phil

46 1011342-90 Machine Screw, Phil

47 9031113-01 Sheet Metal Screw, Phil

48 1011342-08 Lever, Cup Dispense

49 1011342-93 Machine Screw, Phil Rd Hd,

50 1011342-94 Spring, Motor Heater

51 1011342-140 Thread Forming Screw, Phil

52 1011342-149 Clip, Push On

53 1011342-95 Machine Screw, Phil

54 1011342-96 Hose Clamp, Worm

*55 1011342-154 Machine Screw, Phil

*57 1011342-104 Leg

58 1011342-98 Receptacle, 1/4 Turn

59 1011342-99 Retainer, 1/4 Turn

60 1011342-155 Stud Wing Head, 1/4 Turn

61 1011342-97 Spacer, Switch

342-150 Cup Rest

63 1011342-111 Shoulder Screw, No. 8-32

*64 1011342-51 Adapter, 1" Barb x 3/4 MPT

*65 1011342-50 Adapter, 3/4 Soc x 3/4 FPT

66 1011342-35 Bulb, 18" daylight

67 1011342-153 Graphic IOD150 (Not Shown)

* 1011342-101 Water Filler Handle

* Not shown

Note: Part Numbers in BOLD are not stocked items

IOD150, IOD200 and IOD250 Service Parts

Cabinet and Dispenser Parts, IOD200 and IOD 250

IOD150, IOD200 and IOD250 Service Parts IOD 200 and IOD250 Cabinet and Dispenser

Item Item

No. Part No. Description No. Part No. Description

1 1011342-12 Slide, Gate 34 1011342-76 Hex Nut, No. 10-32
*2 1011342-144 Restrictor, Gate 35 1011342-77 Hex Nut, No. 10-32, Nyloc
3 1011342-146 Plate, Motor Mount 36 1011342-63 Tab, Retaining
4 1011342-22 Agitator 37 1011342-92 Screw, No. 10-32 By 3/8-In.
5 1011342-21 Cover, Rear Wrapper 38 1011342-75 Hex Nut, No. 10-32, Keps
6 1011342-142 Panel, Lower Front 39 1011342-143 Washer, No. 10
7 1011342-20 Cabinet 40 1011342-83 Washer,
8 1011342-29 Boot, Switch 41 1011342-89 Screw, No. 8-32 By 3/8-In.

9 1011342-08 Dispense Lever, Short
10 1011342-02 Pin, Drip Tray
*11 1011342-25 Agitator Motor Heater 115 V
12 1011342-26 Dispense Switch
13 1011342-13 Retainer, Ice Dispense lever
14 1011342-33 Bulb, Florescent
15 1011342-41 Agitator Motor 120 Volt
16 1011342-38 Solenoid Ass'y 120 Volt
17 1011342-125 Elec Box Ass'y, 120V IOD 200 1011342-126 Elec Box Ass'y, 120V IOD 250
18 1011342-19 Bracket, Motor Mount
19 1011342-103 Washer, Captivating No. 8
20 1011342-115 Hinge Gusset
21 1011342-70 Seal, Motor
22 1011342-01 Gasket, Gate
*23 1011342-55 Plug
24 1011342-105 Strap, Motor
25 1011342-139 Ice Chute
26 1011342-69 Ice Chute Cover
27 1011342-04 Motor Mount
28 1011342-66 Merchandiser, Black (IOD250)
1011342-65 Merchandiser, Black, (IOD200)
1011342-09 Merchandiser, S.S., (IOD250)
1011342-10 Merchandiser, S.S., (IOD200)
29 1011342-60 Panel, Inner
30 1011342-71 Drip Tray, Black, Insulated 1011342-152 Graphic, IOD250
31 1011342-67 Lid, Dispenser, Black
32 1011342-61 Hopper Ass'y, Insul (ID250)
1011342-59 Hopper Ass'y, Insul (ID200)
33 1011342-63 Tab, Retaining
42 1011342-90 Screw, No. 8-32 By 1/2-In.
43 1011342-91 Screw, No. 8 By 1/2-In. Long
44 1011342-107 Screw, 3/8-16 By 3/4-In. Long
45 1011342-84 Washer
46 1011342-110 Washer,
47 1011342-94 Spring, Motor Heater
48 1011342-154 Screw, No. 8-32 By 1 1/8-In.
49 1011342-149 Clip, Push-on
50 1011342-116 Reflector Panel-IOD200 1011342-120 Reflector Panel-IOD250
51 1011342-140 Sheet Mtl Screw, #10 x 1/2.
*52 1011342-104 Leg
53 1011342-03 Retainer, Agitator
54 1011342-97 Spacer, Switch
55 1011342-109 Wing Nut, 3/8-16
56 1011342-111 Shoulder Screw, No. 8-32
57 1011342-106 Shoulder Screw, 1/4-20
58 1011342-108 Cup Rest
*59 1011342-51 Adapter, 1-In. Barb By 34
MPT (For Drip Tray Drain)
*60 1011342-50 Adapter, 3/4 Soc By 3/4 FPT
(For Drip Tray Drain)
*61 1011342-96 Hose Clamp
(For Drip Tray Drain)
62 1011342-151 Graphic, IOD200
Graphic, IOD250
63 1011342-122 Drip tray extension
* 1011342-100 Faucet Blank Panel
* 1011342-101 Water Filler Handle
* Not shown

Note: Part Numbers in BOLD are not stocked items

IOD150, IOD200 and IOD250 Service Parts Rotary Solenoid

Item

No Part Number Description

1 1011342-15 Arm, Gate Lift

2 1011342-48 Bearing, Gate Arm

3 1011342-39 Solenoid, 120 Volts NLA

4 1011342-14 Plate, Solenoid Mounting

5 1011342-47 Isolator

6 1011342-75 Hex Nut, No. 10-32

7 N/A Locktite

8 1011342-87 Screw, No. 8-32 By 1/4-In. Long

9 1011342-46 Tie Cable

10 1011342-88 Screw, No. 8-32 By 5/8-In. Long

11 1011342-102 Spring, Solenoid Arm

12 1011342-52 Spacer

13 1011342-83 Washer, .218 I.D. By .875 O.D.

14 1011342-82 Lockwasher, No. 10

15 1011342-80 Flatwasher, No. 8

Order 1011342-38 Assembly (page 4-5)

Note: Part Numbers in BOLD are not stocked items

IOD150, IOD200 and IOD250 Service Parts Electrical Box IOD150

Item

No Part number Description

1 1011342-113 Electrical Box (IOD 150)
2 1011342-114 Reflector, Panel (IOD 150)
3 N/A N/A
4 1011342-23 Clamp, Capacitor, 120 Volts
5 1011342-24 Capacitor, 120 Volt

6 N / A N / A

7 1011342-30 Terminal Board
8 N / A N / A
9 1011342-31 Starter
10 1011342-32 Ballast, 120 Volt
11 1011342-138 Timer, Agitation, 120 Volt
12 1011342-124 Socket, Starter
13 1011342-36 Transformer, 120 Volts No Longer Available (Not Used)
14 1011342-123 Lampholder

Not Shown:

1011342-40 Relay, Start, 120 Volts

Note: Part Numbers in BOLD are not stocked items

IOD150, IOD200 and IOD250 Service Parts Electrical Box IOD200 and IOD250

FRONT

RIGHT SIDE

Item Item
No Part numbe r Description No Part numbe

1	1011342-119 Electrical Box (IOD250)	11	1011342-124 Socket, Starter
	1011342-117 Electrical Box (IOD200)	12	1011342-36 Transformer, 120 Volts
2	1011342-120 Reflector Panel (IOD250)	13	1011342-123 Lampholder
	1011342-116 Reflector Panel (IOD200)	14	1011342-40 Relay, Start, 120 Volts
3	1011342-118 Clamp, Capacitor 15 N/		A Not Used
4	1011342-148 Capacitor, Agitator Motor 16 N/		A Not Used
5	1011342-28 Power Cord, 120 Volts 17 N/		A Not Used
6	1011342-27 Terminal Board, 120 Volts	18	N/A Not Used

7 N/A Not Used
8 1011342-31 Starter
9 1011342-32 Ballast, 120 Volts
10 1011342-138 Agitation Timer, 120 Volts

Note: Part Numbers in BOLD are not stocked items

IOD150, IOD200 and IOD250 Service Parts Schematic Diagram

graph TD
    A["LEDA"] --> B["L1 TIMER L2"]
    B --> C["RECTIFIER"]
    C --> D["MOTOR HEATER"]
    D --> E["N.O. CAPACITOR"]
    E --> F["AGITATOR MOTOR"]
    F --> G["GATE SOLENOID"]
    G --> H["BALLAST"]
    H --> I["OPTIONAL LIGHT"]
    I --> J["STARTER"]
    J --> K["OPTIONAL BEVERAGE TRANSFORMER"]
    K --> L["OPTIONAL ICE LEVEL"]
    L --> M["BEVERAGE PANEL"]
    M --> N["OPTIONAL BEVERAGE VALVES"]
    M --> O["OPTIONAL BEVERAGE VALVES"]

FIGURE 8. WIRING SCHEMATIC (120 V UNIT)