B25PP - Ice cream maker Ice-O-Matic - Free user manual and instructions

Product Type	Ice storage bin for ice cream maker
Brand	Ice-O-Matic
Model	B25PP
Exterior Material	Stainless steel
Interior Material	Polyethylene liner
Drain Connection	1" FPT female fitting
Legs	Adjustable; maximum leg extension 1 in. (26mm), total leg height up to 2.125 in. (54mm)
Ice Shield	Adjustable with catch; controls ice flow into lower door area
Lower Door Assembly	Removable for access through narrow doors; includes hinge and screws
Ice Paddle Accessory	Optional; use to break congealed ice mass
Inspection Windows	Removable; size 21.125 x 8.625 in.
Cleaning	Clean interior with food zone cleaner; sanitize periodically
Water Filter Recommendation	Ice-O-Matic IFQ Water Filter to remove chlorine
Safety Caution	Avoid excessive force on drain fitting; avoid excessive heat when sweating fittings
Technical Support	Call 800-423-3367 (US & Canada), 7:30 a.m. – 4:00 p.m. Mountain time
Installation Requirement	Level bin in both directions; connect drain line
Compatible Ice Makers	Various Ice-O-Matic models (see icemaker instructions)
Leg Set	Four stainless steel legs (6 in.) included
Spare Parts Availability	See parts list in manual for replacement items
Shipping	Inspect for damage upon uncrating; notify shipper if damaged
Warranty	Not specified in manual; contact Ice-O-Matic

Frequently Asked Questions - B25PP Ice-O-Matic

How do I level the ice storage bin?

Adjust the foot at the bottom of each leg to level the bin in both directions. Do not extend any leg more than 1 inch (26mm) for a total leg height no greater than 2.125 inches (54mm).

How do I connect the drain line?

Connect the drain line to the 1" FPT female fitting located at the bottom of the bin. Avoid excessive tightening force to prevent damage.

How do I remove the lower door assembly for narrow access?

With the door closed, remove the Phillips head screw and washer from the hinge on each side. Insert a screwdriver between the door and hinge bracket to gently push the bracket, allowing the door stud to clear. Remove the door, then pull up on the Ice Shield to remove it. Finally, remove screws along the top of the door assembly and lift it out.

How does the Ice Shield work?

The Ice Shield controls ice flow into the lower door area. To encourage more ice, gently lift and jiggle the shield using the full-length handle. To lock it at a higher level, pull up, hold, and push the tapered end of the catch into the nearest hole. Pull up to release.

When should I use the Ice Paddle?

If ice is congealed and not flowing into the lower door area, quickly jiggle the Ice Shield several times. If the problem persists, insert the Ice Paddle through the rectangular openings in the shield and agitate it back and forth to break up the ice mass. Keep your head and face clear of the area during use.

How do I clean the interior of the bin?

Remove the inspection windows by sliding them to one side and pulling the front window toward you. Wash the bin walls, hopper, access door plate, and partition with a product suitable for a food zone. Rinse and sanitize. Clean the exterior stainless steel with a stainless steel cleaner.

What water filter does Ice-O-Matic recommend?

Ice-O-Matic recommends installing the IFQ Water Filter on the water supply to the icemaker to remove chlorine, which can affect ice quality and bin longevity.

What precautions should I take when installing the drain?

Avoid excessive tightening force when connecting to the bin drain fitting. Also, do not apply excessive heat if sweating fittings is necessary, as heat conduction through metal can melt the plastic threads in the drain fitting.

How do I install the legs?

Lay the bin on its back (protecting the finish), remove bolts holding the skid, then screw the legs into the tapped holes at the bottom. Tighten to seat the legs well. Set the bin upright and adjust the feet to level.

Where can I get replacement parts?

Refer to the parts list in the manual for part numbers. Contact Ice-O-Matic technical service at 800-423-3367 (US & Canada) or visit their website at www.iceomatic.com to order parts.

USER MANUAL B25PP Ice-O-Matic

Installation Instructions and Parts List

Ice-O-Matic ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this bin delivers that same degree of service, we ask that you take a moment to review this instruction before beginning the installation of the bin. Should you have any questions or require technical help at any point, please call our technical service group at [phone] (US & Canada)

Before You Begin.

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify the shipper immediately and contact Ice-O-Matic so that we can help in the filing of a claim, if necessary.

! Important Cautions

• Avoid excessive tightening force when connecting to the bin drain fitting
• Do not apply excessive heat if any sweating of fittings is necessary. Heat conduction through metal may melt threads in plastic drain fitting.
• When leveling, do not extend any leg more than 1 in. (26mm) for total leg height no greater than 2.125 in. (54mm).

Installation

1. Remove all packing material from bin.
2. Remove all tape and temporary fastenings from door assemblies and outside of bin.
3. Remove set of four legs and any other accessories packed inside bin.
4. Lay bin on back, being careful to protect finish, and remove bolts holding skid to bin.
5. Screw legs into tapped holes in bin bottom and tighten to seat legs well against bottom.
6. Set bin upright.
7. Remove protective paper from stainless steel exterior.
8. Move bin to permanent location.
9. Adjust "foot" at bottom of each leg to level bin in both directions.
10. Mount icemaker(s) on bin in accordance with icemaker manufacturer's instructions.
11. Connect drain line to 1" FPT female fitting located in bottom of bin.
12. Make final connections to icemaker. (Reference the Ice-O-Matic Installation Manual)

Ice-O-Matic

11100 East 45th Ave.

Denver CO 80239

800 423-3367

Bin Model Numbers

www.iceomatic.com

B700-30, B1000-48, B1300-48, B1325-60, B1600-60 01078856R00

9081461-01

12/14

Removing Lower Door Assembly

(Only if required for access through narrow doors)

1. With door in closed position, remove Phillips head screw and washer from hinge area on each side of lower access door.
2. Insert screwdriver between door and hinge bracket on one side of door and gently push against bracket to provide room for door stud to clear bracket.
3. Remove access door.
4. Pull up on Ice Shied to remove.
5. Remove screws along top of door assembly.
6. Pull forward on top of assembly and lift to remove.

Reinstalling Door Assembly

1. Reinstall lower door assembly in bin opening.
2. Reinstall screws in hood at top of door assembly.
3. Reinstall Ice Shield in side panel tracks and push down to seat.
4. With door in closed position, insert one door stud through hinge bracket, install washer, screw and tighten.

Note: For proper operation the access door must be reinstalled in the closed position.

1. On other side, insert screwdriver between door and hinge bracket and gently push against bracket to provide room for door stud to clear bracket.
2. Reinstall washer and screw in lift door and tighten.
3. Check door to ensure proper operation.

Operation

Ice Shield Operation

Ice-O-Matic's unique Ice Shield positively controls the flow of ice into lower door assembly area for removal with either a scoop or shovel.

Ice Shield can also be adjusted and locked at one of several levels to accommodate flow characteristics of different types of ice.

Bin is shipped with Ice Shield in full down position. The Ice Shield can be raised and locked in higher position for better flow or when more access is needed.

If More Ice Is Needed In Lower Door Area:

1. Use full-length handle at top of Ice Shield to gently lift and jiggle the Ice Shield to encourage ice to flow into access area of the bin (Fig. 1). (Loose ice will cascade into lower door area.)
2. When adequate ice has flowed, push the Ice Shield back down.

When More Access Is Needed Or To Encourage Flow Of Less Ice:

1. Lock gate at higher level by pulling up and holding the Ice Shield at correct level, and pushing tapered end of catch into nearest hole in gate (catch will automatically release when you pull up).

2. To release catch, pull up on the Ice Shield.

Fig. 1

Illustration of a hand holding a pen over a printed document with a paper airplane (no text or symbols)

Using Ice Paddle Accessory

The Ice Paddle is an optional accessory that can be ordered directly from Ice-O-Matic. Mount the Ice Paddle for easy access on either side of the bin in the bracket provided.

Using the Paddle

If there is adequate ice in bin but lower door area is not filled with ice, it may be that ice has congealed in bin and cannot flow. This can often be remedied by quickly jiggling the Ice Shield several times (Fig. 1). If problem continues, the Ice Paddle can be inserted through rectangular openings in the Ice Shield and agitated back and forth to break up congealed ice mass (Fig. 2).

Note: Use Ice Paddle only as described above. To avoid possible injury, keep head and face clear of lower door area and Ice Paddle at all times. Do not use the Ice Paddle for other purposes.

Fig. 2

Illustration of a hand holding a tool interacting with a screen displaying a black-and-white graphic (no text or symbols)

Technical assistance available toll free

Should you have any questions concerning installation or maintenance of Ice-O-Matic ice storage bins, please call our technical service department at 800 423-3367 (US & Canada) between 7:30 a.m. and 4:00 p.m. Mountain time.

Cleaning

Interior of bin must be cleaned and sanitized prior to use and should be cleaned on routine basis during use.

Interior Bin Care

Ice-O-Matic single door upright ice storage bins are equipped with polyethylene liner walls and stainless steel bottoms which should be cleaned and sanitized periodically with any product suitable for use in a food zone.

Important: Ice-O-Matic recommends installing our IFQ Water Filter on water supply to icemaker to remove chlorine.

1. Remove upper inspection windows by sliding windows to one side. Grasp the end of the front window and pull toward you as the window is slid to the opposite side. Repeat for rear window.

1. Wash bin walls, hopper, access door plate and partition (if any), rinse and sanitize.

Exterior Bin Care

Exterior stainless steel surfaces can be cleaned with a stainless steel cleaner such as 3M Stainless Steel Cleaner & Polish or equivalent.

Replacement Parts

Item	Ice-O-Matic DES	CRIPTION B700 B1000 B1300 B1325 B1600 Part Number 30 48 48 60 60
1	N/A	No Item Number 1	NA	NA NA		NA NA
2	1011518-10	Inspection Window 21.125 x 8.625 2 Required		XX		XX
2	1011517-10	Inspection Window 21.125 x 8.625 2 Required	X
3	1011518-11	Frame Assembly, Lower Door		XX		XX
3	1011517-11	Frame Assembly, Lower Door	X
4	1011518-12	Door, Outer lift 45 inch		XX		XX
4	1011517-12	Door, Outer lift 28 inch	X
5	1011517-13	Hinge, Right Hand Door Mount (Includes Hardware)	X	XX		XX
6	1011517-14	Hinge, Left Hand Door Mount (Includes Hardware)	X	XX		XX
7	1011518-13	Ice Gate 40 inch With Paddle Access		XX		XX
7	1011518-14	Ice Gate 40 inch With Out Paddle Access		XX		XX
7	1011517-15	Ice Gate 24 inch With Paddle Access	X
7	1011517-16	Ice Gate 24 inch With Out Paddle Access	X
8	1011517-17	Catch, Ice Gate	X	XX		XX
9	N/A	No Item Number 9	NA	NA NA		NA NA
10	1011517-18	Hinge, Bracket, Bin Mount (Includes Hardware)	X	XX		XX
11	1011517-19	Drain Assembly, Plastic	X	XX		XX
12	1011517-20	Legs, 6 inch Stainless Steel (Set of 4)	X	XX		XX
12	1011517-21	Legs, 6 inch Stainless Steel Flanged Foot (Set of 4)	X	XX		XX
NS	1011517-22	Shovel, Ice (Plastic)	X	XX		XX
NS	1011517-23	Bracket, Ice Shovel	X	XX		XX
NS	1011517-24	Paddle Ice, 46.5 Inch Total Length	X	XX		XX
NS	1011517-25	Kit, Top, Replacement B700 Flextop	X
NS	1011518-15	Kit, Top Replacement B1000, B1300 Flextop		XX
NS	1011520-10	Kit, Top Replacement B1325, B1600 Flextop				XX
NS	1011520-11*	Kit, Top Replacement B1325, B1600 Flextop (2 30" Wide)*				XX
NS	1011520-12	Kit, Top Replacement B1325, B1600 Flextop (2 ICE1506)				XX
NS	1011517-26	Bintop Filler Panel, Small, ("S" Lasered into Panel)	XX		X
NS	1011518-16	Bintop Filler Panel, Large, ("L" Lasered into Panel)		XX		XX
NS	1011517-27	Gasket, Foam Rubber, 25 Ft.	X	XX		XX
NS	1011517-28	Sealant, RTV 4.7 Oz. Tube (1 ea.)	X	XX		XX
NS	1011517-29	Bracket, Paddle	X	XX		XX

*Note: For Top Air Discharge, Water Cooled and Remotes Only ICE0250, 400, 500, 606, 806 and 1006 NS = Not Shown

GASKET PATTERN FOR ICE-O-MATIC FLEXITOP 30" WIDE BIN

NO FILLER PANEL REQ'D NO FILLER PANEL REQ'D

ICE 0926 GEM 0956

FILLER 'S'

FILLER 'S'

USING THE ILLUSTRATION FOR THE SPECIFIC ICEMAKER YOU ARE INSTALLING,

INSTALL FILLER PANELS, IF REQUIRED,

BY PEELING PAPER BACKING AND ADHERING TO TOP PER DIMENSION SHOWN.

APPLY 3/8" GASKET TO BIN TOP PER DIMENSIONS SHOWN AND AROUND ICE DROP OPENING. SEAL INSIDE EDGE OF GASKET AROUND ICE DROP OPENING WITH SEALANT SUPPLIED. POSITION ICEMAKER ONTO BIN.

GASKET PATTERN FOR ICE-O-MATIC FLEXITOP

48" WIDE BIN

ICE 1406, ICE 1806, ICE 2106 MFI 2406

NO FILLER PANEL REQ'D

FILLERS'S

(1) GEM 0956 (2) GEM 0956

FILLER 'L'
FILLER 'L'
w/2nd flange

FILLER 'L'
w/2nd flange

USING THE ILLUSTRATION FOR THE SPECIFIC ICEMAKER YOU ARE INSTALLING,

INSTALL FILLER PANELS, IF REQUIRED,

BY PEELING PAPER BACKING AND ADHERING TO TOP PER DIMENSION SHOWN.

APPLY 3/8" GASKET TO BIN TOP PER DIMENSIONS SHOWN AND AROUND ICE DROP OPENING.

SEAL INSIDE EDGE OF GASKET AROUND ICE DROP OPENING WITH SEALANT SUPPLIED.

POSITION ICEMAKER ONTO BIN.

(1) ICE 0926 (2) ICE 0926

GASKET PATTERN FOR ICE-O-MATIC FLEXITOP

60" WIDE BIN

ICE 1406, ICE 1806, ICE 2106 MFI 2406

NO FILLER PANEL REQ'D

FILLER 'L'

(1) GEM 0956 (2) GEM 0956

FILLER 'L'
FILLER 'L' w/2nd flange

FILLER 'L' w/2nd flange

USING THE ILLUSTRATION FOR THE SPECIFIC ICEMAKER YOU ARE INSTALLING,

INSTALL FILLER PANELS, IF REQUIRED,

BY PEELING PAPER BACKING AND ADHERING TO TOP PER DIMENSION SHOWN.

APPLY 3/8" GASKET TO BIN TOP PER DIMENSIONS SHOWN AND AROUND ICE DROP OPENING.

SEAL INSIDE EDGE OF GASKET AROUND ICE DROP OPENING WITH SEALANT SUPPLIED.

POSITION ICEMAKER ONTO BIN.