ECSi210-580 - Water heater DIMPLEX - Free user manual and instructions
Find the device manual for free ECSi210-580 DIMPLEX in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Electric Water Heater |
| Model | ECSi210-580 |
| Brand | Dimplex |
| Capacity | 210 L (approx.) |
| Height | 1500 mm (approx.) |
| Diameter | 580 mm |
| Weight (empty) | 60 kg (approx.) |
| Power Supply | 230 V ~ 50 Hz, 3 kW (approx.) |
| Adjustable Thermostat | Yes, range 30-75 °C |
| Overheat Protection | Yes |
| Pressure Relief Valve | Included (factory-set at 0.8 MPa) |
| Anode Rod | Magnesium or titanium (replaceable) |
| Insulation | Polyurethane foam, 50 mm thick |
| Energy Efficiency Class | B (approx.) |
| Maintenance | Annual check of anode rod and pressure relief valve |
| Cleaning | Wipe exterior with damp cloth; avoid abrasives |
| Safety Features | Overheat thermostat, thermal fuse, safety valve |
| Spare Parts Available | Heating element, thermostat, anode rod, gaskets |
| Mounting | Wall-mount or floor-standing (depending on model variant) |
Frequently Asked Questions - ECSi210-580 DIMPLEX
What are the installation clearance requirements?
Maintain at least 50 cm clearance above the unit for servicing and 30 cm on sides. Ensure the floor is level and capable of supporting the weight when full (approx. 270 kg).
What water pressure is required?
The water heater operates with a maximum inlet pressure of 0.8 MPa (8 bar). If the mains pressure exceeds this, a pressure reducing valve must be installed.
What electrical supply is needed?
The unit requires a 230 V ~ 50 Hz single-phase supply with a dedicated 16 A circuit breaker. Ensure the wiring complies with local regulations.
How do I set the temperature?
Turn the thermostat dial on the front panel to your desired temperature (range 30-75 °C). Recommended setting is 60 °C for energy efficiency and to prevent bacterial growth.
How can I save energy?
Set the thermostat to 55-60 °C, insulate hot water pipes, and use hot water wisely. The unit has 50 mm polyurethane foam insulation for standby heat loss reduction.
Is the heater noisy?
This electric water heater operates silently. If you hear bubbling or popping sounds, it may be due to sediment buildup; consider descaling every 2-3 years.
How often should maintenance be performed?
Inspect the anode rod annually and replace if corroded. Test the pressure relief valve every 6 months by lifting the lever briefly. Drain and flush the tank every 2 years to remove sediment.
What if I have no hot water?
Check the circuit breaker and reset if tripped. Verify the thermostat setting and that the unit is powered. If the problem persists, the heating element, thermostat, or thermal fuse may be faulty.
What should I do if the pressure relief valve leaks?
A small amount of water discharge during heating is normal. If it leaks continuously, the valve may be faulty or the water pressure may be too high. Replace the valve or install a pressure reducing valve.
What is the warranty period?
Dimplex typically offers a 2-year warranty on the entire unit and up to 5 years on the tank for domestic use. Check your local retailer for exact terms.
User questions about ECSi210-580 DIMPLEX
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water heater in PDF format for free! Find your manual ECSi210-580 - DIMPLEX and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ECSi210-580 by DIMPLEX.