SHFUSB10 - Hi-Fi System Sandstrøm - Free user manual and instructions

Product Type	Hi-Fi System with CD, FM/AM Radio, USB Playback, and AUX Input
Brand	Sandstrøm
Model	SHFUSB10
Dimensions (Approx.)	250 x 130 x 250 mm (W x H x D)
Weight (Approx.)	2.5 kg
Power Supply	AC 220-240V, 50/60Hz
Power Consumption	30 W (typical)
Audio Output Power	2 x 10W RMS
Supported Disc Formats	CD, CD-R, CD-RW, MP3 CD
USB Playback	USB 2.0, supports MP3/WMA files up to 32GB
Radio Bands	FM (87.5-108 MHz), AM (522-1620 kHz)
Number of Preset Stations	20 (FM) + 10 (AM)
AUX Input	3.5mm stereo jack
Headphone Output	3.5mm stereo jack
Speaker Configuration	2-way bass reflex speakers
Display	LCD with backlight
Remote Control	Included (battery type: CR2025)
Maintenance & Cleaning	Wipe with soft dry cloth; avoid liquids; clean CD lens with lens cleaner if needed
Safety	Place on flat stable surface; keep away from heat/moisture; unplug during storms/long absence
Spare Parts & Repairability	Contact Sandstrøm support or authorized service center for replacement parts; do not open device yourself

Frequently Asked Questions - SHFUSB10 Sandstrøm

How do I connect my smartphone to the Hi-Fi system?

Use the AUX input on the front or rear panel with a 3.5mm audio cable. Select AUX mode on the system.

Can I play music from a USB flash drive?

Yes, insert a USB drive with MP3 or WMA files into the USB port. Press USB/SD button to select USB mode.

How do I set the clock?

Press and hold the CLOCK button on the remote or main unit. Use TUNE +/- to set hour and minute. Press CLOCK again to confirm.

What should I do if the CD skips or doesn't play?

Try cleaning the CD with a soft cloth. If the problem persists, use a CD lens cleaning disc. Ensure the disc is not scratched or damaged.

How can I improve radio reception?

Extend the FM antenna fully for FM reception. For AM, rotate the built-in ferrite antenna. Avoid placing the system near metal objects or electronic interference.

Can I program the CD player to play tracks in a specific order?

Yes, press PROGRAM while the CD is stopped. Select tracks using TUNE +/- and press PROGRAM to add each. Press PLAY to start programmed playback.

How do I reset the system?

Turn off the unit, unplug it from the mains for about 10 seconds, then plug back in and turn on. This resets the microprocessor.

The remote control doesn't work. What should I check?

Replace the battery with a new CR2025. Point the remote directly at the sensor on the main unit within 5 meters. Remove any obstacles.

How do I clean the system safely?

Use a soft, dry microfiber cloth. Do not use any liquids, alcohol, or chemicals. For the CD lens, use a specialized lens cleaner disc.

Is it possible to connect external speakers?

No, this system is designed with built-in speakers and does not have speaker outputs for external speakers. Use headphone output for private listening.

USER MANUAL SHFUSB10 Sandstrøm

Interior scene with a white armchair, wooden fire pit, and stacked books on a floor (no visible text or symbols)

Exterior view of a modern audio streaming setup with two Soundstrom speakers, a remote control, and a CD-ROM (no visible text or symbols)

Contents

Unpacking....5

Product Overview....6

CD Player 6

Front View 6

Top View....6

Control Panel....6

Rear View 6

The Amplifier ....7

Front View 7

Rear View ....7

Remote Control....8

Remove the Insulating Strip from the Remote Control....9

Battery Installation for the Remote Control....9

Remote Control Operation Range....10

Connections....11

1. Connecting the FM Aerial .... 11

2. Speaker Connections .... 11

3. Connecting Auxiliary Equipment 12

4. Connecting Control Cable 12

5. Connecting to the Mains Supply....12

ECO-Power/Standby Features ....13

Sound Quality 13

Adjusting the Volume 13

Adjusting the Super Bass....13

Control the Loudness....13

Preset Equalizer....13

Changing the Display Darkness....13

Listening to Radio Broadcasts....14

Tuning in a Station....14

Presetting Stations....14

To change the FM Reception Mode....15

RDS (Radio Data System) Reception 15

CD Operation 16

Compatible Disc Types....16

CD Playing....16

To Skip Search or Search and Play....16

Program Play....17

Random Play (CD and MP3 discs)....17

Playing the Beginning (Intro) of each Track....17

Text Display During Playback 17

Playing Repeatedly....17

MP3 Disc Playing ....18

Playing Repeatedly....18

Using the USB 19

Setting the Clock Automatically....19

Setting the Clock Manually....19

Setting the Sleep Timer....20

Setting the Daily on Timer 21

To Deactivate or Re-activate an Daily Timer....21

AUX Input 21

Maintenance 22

Hints and Tips ......23

Specifications....24

Safety Warnings....25

Thank you for purchasing your new Sandstrøm 100 Watts Hi-Fi Component System.

We recommend that you spend some time reading this instruction manual in order that you fully understand all the operational features it offers. You will also find some hints and tips to help you resolve any issues.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Unpacking

Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

Diagram of a speaker with concentric circles and two speakers, labeled 'Speakers x 2' below (no other text or symbols)

Remote Control

FM Aerial x 1

Control Cable x 1

Speaker Cable x 2

If items are missing or damaged, please contact Partmaster (UK only).

Tel: [phone] for assistance.

Product Overview

CD Player

Front View

1. Standby Button
2. Remote Sensor IR
3. Display
4. USB Port

Top View

1. Disc Door

Control Panel

6 MODE Button

Stereo / Mono Button

1. Tuning ◀ Button
2. Tuning ▶▶ Button
3. Play/Pause ▶ II Button
4. Stop ■ Button
5. Preset ◀◀ Button
6. Preset ▶▶ Button
7. Open/Close ▲ Button

Rear View

1. Control Cable Connector
2. Line Out Terminals (L&R)
3. AUX Input Terminals (L&R)
4. FM Aerial Socket

The Amplifier

Front View

1. LOUDNESS Button
2. Preset Equalizer P-EQ Button
3. -VOLUME + Control
4. FUNCTION Button
5. Headphone 📄 Socket

Rear View

1. Mains Cable
2. Control Cable Connector
3. Left & Right Speaker Output Terminals

Remote Control

1. Standby Button
2. CD Function
3. Tuner Function
   4 RANDOM Button
   5 INTRO Button
4. Dimmer Button DIM
5. Preset Equalizer Button P-EQ
   8 CLOCK Button
6. Preset
7. Tuning Button
8. Preset ◀◀ Button
9. Play/Pause ▶■Button
10. Album Up Button ALB+
11. Album Down Button ALB-
12. MUTE Button
13. Number Buttons
14. Open/Close ▲ Button
15. USB Function USB Button
16. AUX Function AUX Button
17. Repeat A-B Button A-B
18. MODE Button Stereo / Mono Button
19. LOUDNESS Button
20. Super Bass S-BASS Button
21. SLEEP/TIMER Button
22. CD Display DISPLAY Button RDS Display Button
23. Tuning ▶ Button
24. Stop ■ Button
25. VOL + Button
26. VOL - Button
27. Program PROG Button

Remove the Insulating Strip from the Remote Control

Remove the insulating mylar strip from the battery if the battery is being used for the first time. It is located at the bottom back side of the remote control.

Illustration of a hand holding a bottle with an arrow indicating direction (no text or symbols)

Battery Installation for the Remote Control

1. Unwind the screw and slide open the battery compartment of the remote control.

Line drawing of a smartphone with a screwdriver inserted, showing the needle and rotation (no text or symbols)

1. Remove the old battery, and place a new battery (CR2025 Lithium Battery) in the holder.

Diagram showing a device with directional arrows and a separate mechanical component (no text or symbols)

1. Close the battery compartment cover and wind the screw back on.

Illustration of a hand holding a small object with an arrow indicating direction (no text or symbols)

Handling the Battery

- Improper or incorrect use of batteries may cause corrosion or battery leakage, which could cause fire, personal injury or damage to property.

• Install the battery correctly by following the polarity (+ and -) indications in the battery compartment.

- When the battery is exhausted, the remote control will not function.

• Only use the battery type indicated in this manual.

- Do not dispose of the used battery as domestic waste. Dispose of it in accordance with local regulations.

- Small button cell batteries such as the one used in the remote control are easily swallowed by young children and this is dangerous. Keep loose button cells away from young children and make sure that the battery holder tray is secure in the remote control. Seek medical advice if you believe a cell has been swallowed.

Handling the Remote Control

• Take care of your fingernails when you press and hold the battery release tab.
- Do not drop or cause impact to the remote control.
- Do not spill water or any liquid on the remote control.
- Do not place the remote control on a wet object.
- Do not place the remote control under direct sunlight or near sources of excessive heat.
- Remove the battery from the remote control when not in use for a long period of time, as it could cause corrosion or battery leakage and may result in physical injury and/or property damage including fire.

Remote Control Operation Range

Point the remote control at the unit no more than 5 metres from the remote control sensor and within 60^ of the front of the unit. The operating distance may vary depending on the brightness of the room.

Connections

1. Connecting the FM Aerial

Connect the FM wire aerial provided to the FM Aerial socket as illustrated below.

1. FM Aerial
   

Back view of a portable electronic device showing ports, cables, and connectors (no text or symbols visible)

Connect the FM wire aerial to the FM aerial socket on the rear of the CD player.

1. FM Aerial
   

If reception is poor, connect the unit to an outdoor aerial.

• Before attaching a 75 ohm coaxial lead (the kind with a round wire going to an outside aerial), disconnect the supplied FM wire aerial.
  • To avoid noise, keep antennas away from the system, the control cable and the mains cable.

2. Speaker Connections

Connect the speaker cables at the back of the speakers to the speaker sockets (L/R) at the rear side of the amplifier.

3. Connecting Auxiliary Equipment

Connect the AUX INPUT sockets at the rear of the CD player to the line output sockets on the auxiliary equipment using RCA stereo audio cables (not included) as illustrated below.

graph LR
    A["The CD Player"] --> B["Control Cable"]
    B --> C["LIVE OUT"]
    C --> D["Audio Out"]
    D --> E["Auxiliary equipment"]

Connect the LINE OUT sockets at the rear of the CD player on this unit to the auxiliary input sockets on the auxiliary equipment as illustrated below.

graph LR
    A["The CD Player"] --> B["Controller Unit"]
    B --> C["Wireless Portugal"]
    C --> D["Switch"]
    D --> E["Line 4V"]
    E --> F["Auxiliary equipment"]
    F --> G["Monitor"]

4. Connecting Control Cable

Connect the control cable between the CD player and the amplifier.

5. Connecting to the Mains Supply

Insert the mains plug into a wall socket. Your system is now ready to use.

ECO-Power/Standby Features

This unit features an ECO-Power/Standby mode. Press the STANDBY ⏻ button on the remote control or on the unit to enter standby mode. To save energy consumption, the clock will not be displayed.

If you want to display the clock during standby mode, you can press the CLOCK button. The clock display will disappear after 90 seconds.

Sound Quality

Adjusting the Volume

To increase or decrease the volume, rotate the VOLUME+ / - control on the CD player or press the VOL+ / - buttons on the remote control.

Adjusting the Super Bass

You can reinforce the bass sound to maintain rich, full bass at low volume.

Press the S-BASS button on the remote control to get the effect. The "S-BASS" will show on the display. Press the S-BASS button again to cancel the effect.

Control the Loudness

This unit has a loudness function. It can automatically increase the bass sound at low volume (the higher the volume, the smaller the bass increase). Press the LOUDNESS button on the remote control to obtain the loudness function. The “LOUD” will show on the display.

Preset Equalizer

You can adjust the sound reproduced by pressing the P-EQ button repeatedly.

Select from one of the 5 preset equalizer:

Changing the Display Darkness

To dim or brighten the display, press the DIM button repeatedly on the remote control to the desired brightness.

Listening to Radio Broadcasts

You can listen to FM stations. Stations can be tuned in manually, automatically, or from preset memory storage.

Before listening to the radio, please check that the FM antenna is correctly connected and adjusted for length and direction or that the unit is connected to an external FM antenna.

Tuning in a Station

1. Press the FUNCTION button repeatedly on the front of the amplifier or press the TUNER on the remote control to select tuner function.
2. Select a station using one of the following methods.

- Manual Tuning

Press the TUNING ↕ button repeatedly to change the frequency until you find the station you want.

- Auto Tuning

If you press and hold the TUNING button for one second or more, the frequency changes down, or up, automatically until a station is found.

- Preset Tuning (Possible only after presetting stations)

Press the PRESET ▶ button repeatedly to select the desired preset number. Its band and frequency are shown on the display.

Presetting Stations

You can preset up to 20 FM stations.

Automatic

1. Press and hold the PROG button on the remote control until "AUTO" shows on te display.
2. First 20 available stations found will be stored.
3. When automatic preset is completed, the first preset station will start boardcast.

Manual

1. Press the PROG button on the remote control, the "PROG" will show on the display and the preset number will flash.
2. Press the PRESET ◀◀/▶button to select the preset number.

PRESET - / ▶Decreases	the preset number by 1
PRESET +/ ▶Increases	the preset number by 1

If you select more than 20, the preset number will be changed to "1" automatically.

1. Press the PROG button on the remote control to store the station. After 1 second, the display returns to the broadcast frequency display.

2. Repeat above steps 1 to 3 for each station you want to store in the memory with a preset number.

If the system is unplugged or if a power failure occurs, the preset stations will not be erased.

To change the FM Reception Mode

When you are tuned into a FM stereo broadcast, "ST" will be displayed and you can hear stereo effects.

If a FM stereo broadcast is hard to receive or noisy, you can select MONO by pressing the MODE button and the "ST" will not display. Reception will be improved, but you will lose any stereo effect.

RDS (Radio Data System) Reception

Many FM stations are broadcasting added data compatible with RDS. This radio set offers convenient functions using such data.

• PS (Program Service Name)

When an RDS station is received, the "RDS" and the name of that station will be displayed. When the DISPLAY button on the remote control is pressed during PS display, the CT is displayed for 3 seconds, then PS display returns.

• PTY (Program Type)

Program type identification signal. (Example: News, Rock, Classical music.)

• CT (Clock Time System)

- The CT system may not properly operate in areas where RDS CT service is not available. Once CT service is received, the CT system keeps operating. "RDS CLOCK" is displayed in areas where no CT services are available.

- Changing Display

During PS display, press the DISPLAY button on the remote control repeatedly to select the CT, PTY or Frequency. They will be displayed for 3 seconds, then the PS display returns.

Compatible Disc Types

Disc Types Disc Logo Recorded Content
CD-R (CD Recordable - Audio/MP3/WMA)		AUDIO / MP3 / WMA
CD-RW (CD-Rewritable - Audio/MP3/WMA)		AUDIO / MP3 / WMA
AUDIO-CD (Compact Disc Digital Audio)		AUDIO

Some recorded files may not be able to be played due to the type and format of disc or condition of the recording.

CD Playing

1. Press the FUNCTION button repeatedly on the front of the amplifier until "DISC" is displayed or press the CD button on the remote control to select CD function.
2. Press the ▲ button to open the disc door and place the disc on the disc tray (with the printed side up).
3. Press the ▲ button to close the disc door, the unit will read the disc and play it automatically.

If in stop mode, please press the ▶ button to start playing the disc.

1. Press the ▶ button to pause the playback, the time elapsed indicator will flash.
2. To resume playback, press the ▶■ button again.

To Skip Search or Search and Play

• Press the PRESET◄◄ button once or more to skip to the previous one or more tracks of the disc.
• Press and hold the TUNING button to search backwards for the track position that you want to start playing from.
• Press the PRESET▶ button once or more to skip forward one or more tracks on the disc.
• Press and hold the TUNING▶ button to search forward for the track position that you want to start playing from.

Program Play

1. Insert a disc and press the button when it starts playing.
2. Press the PROG button on the remote control.
3. Press the PRESET ←, buttons or 0-9, 10+, buttons on the remote control to select the desired track number and then press the PROG button to confirm your program.
4. Repeat the above step 3 to enter more tracks.
5. Press the ▶II button to start program play.
6. Press the ■ button to stop the program play and press the ▶ button to start program play again. Press this button again to exit programme mode.
7. Press the ■ button twice to clear programmed memory.

Random play will not shuffle the programmed music list.

Random Play (CD and MP3 discs)

The CD can be played randomly.

Random play begins by pressing the RANDOM button on the remote control in stop mode.

Playing the Beginning (Intro) of each Track

Press the INTRO button on the remote control to play the beginning of each track consecutively. The playing time of each track is 10 seconds.

When you hear the desired track, press the play/pause button twice.

Text Display During Playback

Repeatedly press the DISPLAY button on the remote control to show the current track number and single remain time / the current track number and single elapsed time / total track number and total remain time.

Playing Repeatedly

* For CD disc, ONE and ALL repeat play can be set by pressing the MODE button repeatedly.

First press : To repeat the same track over and over again, ("REP" will flash).

Second press : To repeat all tracks on a disc and then play them again and again, ("REP" will stay lit).

Third press : To cancel the repeat playing, ("REP" off).

* You can use this function to enjoy the certain part of a disc which you like repeating.

When it is playing, press the A-B button on the remote control at the beginning of the content that needs repeat playing. Press the A-B button again at the end of the content that needs repeat playing. Then the player will repeatedly play between A and B until you press the A-B button again to cancel the repeat and the setting turns to normal playing mode.

A-B repeat function can only be used within the same track.

MP3 Disc Playing

When selecting tracks the player will automatically display the album and track number.

For example: track number 21 may be from album 3, track 7.

1. Press the ▲ button to open the disc door and place the MP3 disc on the disc tray.
2. Press the DISPLAY button on the remote control, ID3 information (song title and artist) will be displayed or "NO ID3" if there is no ID3 information. Press this button again, album, track and playing time will be displayed.
3. When playing MP3 discs, the current album and track will be displayed.
4. Press the PRESET ◀◀, ▶button to select the previous/next track. Press and hold the TUNING ◀◀ button to search backward or forward.
5. PresstheALB +/ - button on the remote control to select the next /previous album, and play the first track of the album.

If playing has ended, press the ALB+ / - button on the remote control to select the next/previous album. Then choose the track with the PRESET◀◀,▶button.

1. Press the ▶■ button to start playing the disc.
2. Press the ■ button to stop playback.

Play will continue to the final track when the selected tracks have been played.

The first 2 digits of the display is the album number, the next 3 digits is the track number and the remaining digits display the minutes and seconds.

Playing Repeatedly

For MP3 disc, ONE, ALB and ALL repeat play can be set by pressing the MODE button repeatedly.

• First press : To repeat the same track.
• Second press : To repeat ALB (Album).
• Third press : To repeat ALL (All albums and tracks).
• Fourth press : To cancel the repeat playing.

The word ALB will appear on the display to indicate the albums stored on your MP3 disc.

Using the USB

By connecting a USB mass storage device (including USB flash memory, USB flash players or memory cards) to this unit, you can enjoy the device's stored music through the powerful speakers of this unit.

1. Insert the USB device's USB plug into the port on the front of the CD player
2. Press the FUNCTION button Repeatedly upon the front of the amplifier or press the USB button on remote control to select the USB function until "USB DIR" appears on the display.
3. The device's stored music will be played automatically.

For devices with a USB cable:

1. Insert one plug of the USB cable (not supplied) to the port on the front of the CD player.
2. Insert the other plug of the USB cable to the USB output terminal of the USB device.

For memory cards:

1. Insert the memory card into a card reader (not supplied) to the front of the CD player.
2. Use a USB cable (not supplied) to connect the card reader into the socket on the set.

Setting the Clock Automatically

Tune into a RDS station and wait for a few minutes, the clock will be automatically set. To view the time, press the CLOCK button in standby mode.

Setting the Clock Manually

The built-in clock shows the time on the display.

1. In standby mode, press and hold the CLOCK button until the display shows CLOCK SET and [24 HR] begins to flash.
2. Set the 12/24 hour format with the VOL + / - button.
3. Press the CLOCK button, hour indicator will flash.
4. Set the hour with the VOL + / - button.
5. Press the CLOCK button, minute indicator will flash.
6. Set the minute with the VOL + /- button.
7. Press the CLOCK button to confirm. The clock is now set.

• The operating time of every step shouldn't be longer than 90 seconds or it will return to the time display.
• If there is a power failure or the systems power is turned off, the clock will lose its setting.

Setting the Sleep Timer

Use the sleep timer to turn the system off after a certain number of minutes when in play mode. By setting the sleep timer, you can fall asleep to music and know that your system will turn off by itself rather than play all night.

1. Play a CD or tune in to the desired station.
2. To set the sleep timer press the SLEEP/TIMER button on the remote control repeatedly, it changes the number of minutes shown on the display in this sequence:

After setting the number of minutes for the sleep timer, the display will return to the previous display.

The system is now set to turn off after the number of minutes you set. The display will show "SLEEP".

To confirm the sleep time

When the SLEEP/TIMER button on the remote control is pressed once, the remaining sleep time is displayed. Wait for a second until the display returns to the original display.

To cancel the sleep timer setting

Press the SLEEP/TIMER button repeatedly on the remote control until the "OFF" is displayed.

Turning off the system also cancels the sleep timer.

Setting the Daily on Timer

You can use the setting timer to make the unit automatically turn on at a certain time everyday from standby. When the setting timer is on, the timer indicator "①" will be displayed. The clock must be correctly set for the timer to operate correctly.

1. In standby mode, press and hold the SLEEP/TIMER button on the remote control, the display will show "TIMER SET". Then "USB" will show on the display
2. Select USB/TUNNER/DISC mode with the VOL + / - button.
3. Press the SLEEP/TIMER button on the remote control, hour indicator will flash.
4. Set the hour with the VOL + / - button.
5. Press the SLEEP/TIMER button on the remote control, minute indicator will flash.
6. Set the minute with the VOL + / - button.
7. Press the SLEEP/TIMER button on the remote control, volume indicator will flash.
8. Adjust the volume with the VOL + / - button.
9. Press the SLEEP/TIMER button on the remote control to confirm the setting.

• You can set the daily timer only in standby mode.
- The operating time of every step shouldn't be longer than 90 seconds or it will return to the time display.

To Deactivate or Re-activate an Daily Timer

In standby mode, repeatedly press the SLEEP/TIMER button on the remote control to activate or deactivate timer.

AUX Input

There is a RCA (L/R) sockets located at the back of the unit. Analogue audio sound signals from other sources can be input to the unit through these 2 sockets.

1. Connect the input to another audio device via an audio cable (not included) with RCA (L/R) socket.
2. Press the FUNCTION button repeatedly or press the AUX button on the remote control to select the AUX Input function until "AUX" appears on the display.
3. Adjust the volume control for your desired sound output level.

Maintenance

Handling Discs

• Do not touch the playback side of the disc.
• Do not attach paper or tape to the disc.

Cleaning Discs

- Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the centre outwards with a soft cloth. Always keep the disc clean.

• If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth.
• Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray. They may damage the disc.

Storing Discs

• Do not store discs in places subjected to direct sunlight or near heat sources.
- Do not store discs in places subjected to moisture and dust such as a bathroom or near a humidifier.
- Storing discs vertically in a case, stacking discs or placing objects on discs outside of their cases may cause warping.

Hints and Tips

If a problem does occur, it may often be due to something very minor. The following table contains various tips.

Problem Cause / Solution
CD
The unit does not power on	Make sure the mains plug is secure in the outlet, and the outlet has power.Make sure you've selected CD mode.
Disc in place but the unit won't play	Make sure the disc label is facing up.Make sure the disc is clean.PAUSEmode may be activated, deactivate it.Disc may be damaged or dirty; check and clean the disc.
Disc skips	Make sure the unit is on a secure spot. Vibrations or jarring can cause the disc to skip.
RADIO
Poor FM reception	Make sure the FM antenna wire is fully extended.Electrical interference in your home can cause poor reception. Move the unit away from them (especially those with motors and transformers).

Specifications

Model SHFUSB10
Power Supply 230V ~50Hz
Output Power 50 Watts x 2
Unit Dimension 192 (W) x 250 (D) x 130 (H) mm
Speaker Box Dimension 127 (W) x 195 (D) x 200 (H) mm
N.W.: 6 kg
Radio Section
Frequency Range FM 87.5 – 108 MHz
Compact Disc Section
Optical Pickup 3 - Beam Laser
Frequency Response 100Hz – 16kHz
USB Section
USB Memory StickMemory Size	Up to 16 GB

Features and specifications are subject to change without notice.

Safety Warnings

• Read all the instructions carefully before using the unit and keep them for future reference.
• Retain the manual. If you pass the unit onto a third party make sure to include this manual.
• Check that the voltage marked on the rating label matches your mains voltage.

Damage

• Please inspect the unit for damage after unpacking.
• Do not continue to operate the unit if you are in any doubt about it working normally, or if it is damaged in any way - switch off, withdraw the mains plug and consult your dealer.

Location of Unit

• The unit must be placed on a flat stable surface and should not be subjected to vibrations.
- Do not place the unit on sloped or unstable surfaces as the unit may fall off or tip over.
- The mains socket must be located near the unit and should be easily accessible.
• This unit is designed for indoor use only.

Temperature

• Avoid extreme degrees of temperature, either hot or cold. Place the unit well away from heat sources such as radiators or gas/electric fires.
• Avoid exposure to direct sunlight and other sources of heat.

Naked Flames

- Never place any type of candle or naked flame on the top of or near the unit.

Moisture

• To reduce the risk of fire, electric shock or product damage, do not expose this unit to rain, moisture, dripping or splashing. No objects filled with liquids, such as vases, should be placed on the unit.
• If you spill any liquid into the unit, it can cause serious damage. Switch it off at the mains immediately. Withdraw the mains plug and consult your dealer.

Ventilation

• To prevent the risk of electric shock or fire hazard due to overheating, ensure that curtains and other materials do not obstruct the ventilation vents.
• Do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure the unit is well ventilated.

Safety

• Always disconnect the unit from the mains supply before connecting/disconnecting other devices or moving the unit.
• Unplug the unit from the mains socket during a lightning storm.

Mains Cable

• Make sure the unit or unit stand is not resting on top of the mains cable, as the weight of the unit may damage the mains cable and create a safety hazard.
• If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

Earphones

• Listening to loud sounds for prolonged periods of time may permanently damage your hearing.
• Before putting on earphones, turn the volume down then put the earphones on and slowly increase the volume until you reach a comfortable listening level.

Interference

- Do not place the unit on or near appliances which may cause electromagnetic interference. If you do, it may adversely affect the operating performance of the unit, and cause a distorted picture or sound.

Standby

- The STANDB button on the remote control does not switch off the unit completely. The unit will continue to draw electricity from the mains supply while in standby. In the interests of safety and to avoid unnecessary energy consumption, never leave the unit in standby while unattended for long periods of time, e.g. overnight, while on holiday or while out of the house. Switch it off and disconnect the mains plug from the mains socket.

Batteries

• Batteries used in the remote control for this unit are easily swallowed by young children and this is dangerous.
• Keep loose batteries away from young children and make sure that the battery holder tray is secure in the remote control. Seek medical advice if you believe a cell has been swallowed.
• Please dispose of batteries correctly by following the guidance in this manual.

Supervision

• Children should be supervised to ensure that they do not play with the unit and the remote control.
• Never let anyone especially children push anything into the holes, slots or any other openings in the case - this could result in a fatal electric shock.

Class 1 Laser Product

• This unit utilises a laser. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Before moving the unit, ensure the disc tray is empty.
  • Always remove the disc when the unit is not in use.
  • Failure to do so will risk severely damaging the disc and the unit.
• Do not stack devices, heat from other devices may affect the performance of the unit.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the unit’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the manual accompanying the unit.

Service

• To reduce the risk of electric shock, do not remove screws. The unit does not contain any user-serviceable parts. Please leave all maintenance work to qualified personnel.
• Do not open any fixed covers as this may expose dangerous voltages.

Maintenance

• Ensure to unplug the unit from the mains socket before cleaning.
• Do not use any type of abrasive pad or abrasive cleaning solutions as these may damage the unit's surface.
  • Do not use liquids to clean the unit.

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to

your door the very next day. Visit www.partmaster.co.uk or call 0844 800 3456 (UK customers only) Calls charged at National Rate.

Notes for battery disposal

The batteries used with this product contain chemicals that are harmful to the environment. To preserve our environment, dispose of used batteries according to your local laws or regulations. Do not dispose of batteries with normal household waste.

For more information, please contact the local authority or your retailer where you purchased the product.

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU.

For more information, please contact the local authority or your retailer where you purchased the product.

This product is not designed, manufactured, sponsored or endorsed by Apple Computer, Inc.

iPod is a trademark of Apple Computer, Inc. registered in the U.S. and other countries.

All trademarks are the property of their respective owners and all rights are acknowledged.

DSG Retail Ltd • Maylands Avenue • Hemel Hempstead Herts • HP2 7TG • England