PRA70 - Range hood Premier - Free user manual and instructions

Product Type	Under-cabinet range hood (cooker hood)
Brand	Premier
Model	PRA70
Installation Distance	65-75 cm (26-30 in) from cooking surface
Voltage	220-240 V
Frequency	50 Hz
Motor Type	Centrifugal (high power)
Number of Speeds	3 (low, mid, high)
Controls	Electronic push buttons with indicator
Lighting	LED lamps (isolated low voltage input)
Filter Type	High-density grease filter (washable)
Material	High quality materials, streamlined design
Air Extraction	Ducted (extensible pipe to outside)
Chimney	Telescopic chimney included
Safety Features	Child safety, anti-leakage ventilation, overheat protection
Maintenance	Grease filter: soak in warm water (40-50°C) with mild detergent; main body: non-corrosive detergent; carbon filter replacement
Warranty	As per warranty card (keep purchase receipt)
Weight	Approx. 12 kg (estimated)
Dimensions	Width: 70 cm; Depth: 50 cm; Height: adjustable with chimney (estimated)

Frequently Asked Questions - PRA70 Premier

What is the recommended installation height for the Premier PRA70 range hood?

The cooker hood should be placed at a distance of 65-75 cm (26-30 inches) from the cooking surface for best performance.

How do I clean the grease filter?

You can wash the high-density grease filter by soaking it in warm water (40-50°C) with mild detergent for 2-3 minutes, then gently scrubbing. Alternatively, you can wash it at around 60°C if the filter material allows.

Can I use the range hood with a gas stove?

Yes, but ensure the room is well-ventilated and do not exhaust the gas from the cooker hood together with other gas appliances. The hood should not share the same air duct with gas tubes or water heaters.

How do I replace the light bulb?

If the light does not work, check if the light is damaged. If so, replace it with a compatible LED lamp. Always disconnect power before replacing.

What should I do if the motor does not work but the light turns on?

This may indicate a blocked fan blade, a damaged capacitor, or a jammed motor bearing. Clear any blockages or replace the capacitor/motor as needed.

How often should I clean the carbon filter?

The carbon filter should be replaced periodically rather than cleaned. Frequency depends on usage, typically every 3-6 months.

Can I install the hood myself?

Installation must be carried out by a competent fitter to ensure safety and proper operation. The manufacturer disclaims liability for improper installation.

What does the wind tunnel construction do?

The special wind tunnel construction ensures that dirt is absorbed in a second, providing efficient smoke and odor extraction.

Why is the hood shaking or noisy?

Shaking can be due to loose mounting or damaged fan blade. Tighten the fixing screws or replace the blade if damaged. Also check if the motor is tightly secured.

What voltage and frequency does the PRA70 require?

The cooker hood is designed for 220-240V, 50Hz. Always check that your household voltage matches before installation.

USER MANUAL PRA70 Premier

1. Thank you for choosing our cooker hood. Please read the instruction manual carefully before use.

2. The installation work must competent fitter.

3. The manufacturer disclaims injury caused as a result of not installation contained in the

The cooker hood is used on 22

(2)FEATURE

1. The cooker hood uses high quality materials, and is made with a streamlined design.
2. Equipped centrifugal with a large power grease filter leaf, it produces strong and easy to clean.
3. With the isolated low voltage input, the lights are therefore sa
4. Special wind tunnel construction dirt will be absorbed in a second.

(3). Installation

3.1 The cooker hood should be placed at a dis of 65-75cm (26-30inch) from the cooking surface the best effect. See Pic

3.2 Install the hook installation height is

fixed position of the place of chimney.

3.3 Fix the extensible direction and way, the hook. S ee pic 3.

1. 4 Put the glass according to the way on the cooker hood, and then lead the extensible pipe outside of the inside chimney to the position fix on it by screw, here should be freely. See Pic 4.

2. 5 Put the two chimneys together adjust the height of the inside chimney inside chimney body with safety to the inside chimney Note: The two safety screw. See Pic pos

diameter of 6mm.

(4) NOTICE OF INSTALLATION

1. Before installation, please ensure the area is clean to avoid suction of the remaining bits
2. It cannot share the same air appliance such as gas tube, w
3. The above wall. bending the start of ventilation point and should
4. After grease installation, collection make at one sure end.

Pic5

(5) SAFETYWARNING

✧ Keep your children from using the cooker hood.

✿ Your cooker hood is for domestic use and other commercial use.

✿ Any installation work must be carried person.

The cooker hood and its filter mesh in good working order.

Before cleaning, always ensure that

✿ Clean the cooker hood according to hood from the danger of burning.

✿ N o fire for drying your cooker hood.

If there is any fault with your cooker appointed by agent for servicing.

✧ Please keep the room draughty when

Do not exhaust the gas from cooker for the gas from gas hob and other kitchen

Before installation and usage, read a voltage (V) and the frequency (Hz) i same as the voltage (V) and the frequency

In order to get the most out of your cook manual before installing & using, and

✿ Ensure that you could get our guarantee warranty card and purchase receipt,

✿ CAUTION: Accessible parts may be appliances.

(6 6)SpeSpedbjutramntSSeqpjtatness

Electronic BButton

1. Push runs at the low low speed. button, Push the it indica again

2. Push the middle button, the motor runs at mid speed. Push

3. Push the high button, the indi on high speed. Push it again

4. Push the light button; the ind lighting lamps will come on. turn off.

Indicatorlight ① ② ③ ④

Pic6A

(7) MAINTENANCEE

7.1 The cleaning of the carbon-grease filter mesh

The filter mesh is made of high-density use the corrosive detergent on the appliance running correctly. below.

Method and soak 1: Put the mesh into 40-5 and soak for 2-3 mins. Wear glov Please do not apply too much p will damage easy.

Method 2: If instructed to do so, the temperature at around 60 de

7.2 Notice of cleaning geokkerhood

hood

A. To time, protect the cooker the main hood body should non corrosive detergent every

B. Please do not use abrasive body.

C. Keep the motor and other spare will cause damage to the appliance

D. Before cleaning the appliance power

E. The carbon filter shouldn't

F. Please don't tear open the

G. If the plug or cord is damaged, soft cord.

8.Abnormity anddSolution

Fault	Cause		Solution
Light on, but motor does not work	The leaf blocked		Get rid of the bloc
	The capacitor damaged		Replace capacitor
	The motor jammed bearing damaged		Replace motor
	The internal a bad smell from th		Replace motor
Light does not wor motor does not wor	Beside the above mentione
	Light damaged	Replace lights
	Power cord	Connect the electric
Oil leakage	One way valve ventilation tightly sealed	Take down valve and seal with
	Leakage from of U-shaped cover	Take U-shaped down and seal or paint
Shake of	The leaf damaged shaking	Replace the leaf
	The motor is not tightly hanged	Lock the motor
	The body is not hanged	Fixed the body
Insufficient	The distance body and the gas	Readjust
	Too much open doors	Choose a resemble
The machine	The fixing screw enough	Tighten the screw and ma horizontal
	The hanging screw enough	Tighten the screw and ma horizontal