SVD065 - Weather Station JOHNSON - Free user manual and instructions

Product Type	Weather Station
Brand	Johnson
Model	SVD065
Indoor Unit Dimensions	100 x 100 x 20 mm
Outdoor Sensor Dimensions	60 x 40 x 120 mm
Total Weight	200 g (including batteries)
Power Supply	2 x AA batteries for indoor unit, 2 x AAA batteries for outdoor sensor
Display Type	LCD
Measured Parameters	Indoor/Outdoor temperature, humidity, barometric pressure, weather forecast
Additional Functions	Time and date display, alarm clock, moon phase, temperature trend
Wireless Range	Up to 100 m (open area)
Transmission Frequency	433 MHz
Operating Temperature Range (Indoor Unit)	0°C to 50°C
Operating Temperature Range (Outdoor Sensor)	-20°C to 60°C
Humidity Range	20% to 95% RH
Barometric Pressure Range	700 to 1100 hPa
Battery Life	Approximately 12 months
Cleaning and Maintenance	Wipe with a soft, dry cloth. Do not use water or solvents.
Safety Precautions	Keep away from water and heat sources. Replace batteries promptly when low.
Spare Parts	Outdoor sensor (optional), batteries
Reparability	No user-serviceable parts. Contact support for repairs.
General Information	Free manual available in PDF format on notice-facile.com.

Frequently Asked Questions - SVD065 JOHNSON

How do I set up the Johnson SVD065 weather station?

Insert batteries into both the indoor unit and outdoor sensor. Place the outdoor sensor within 100 m of the indoor unit. The indoor unit will automatically sync and display readings. Refer to the manual for detailed settings.

Where should I place the outdoor sensor?

Mount the outdoor sensor in a shaded, sheltered location away from direct sunlight, rain, and heat sources. Ensure it is at least 1.5 m above ground for accurate readings.

What type of batteries does the SVD065 use?

The indoor unit requires 2 x AA batteries. The outdoor sensor uses 2 x AAA batteries. Use alkaline batteries for best performance.

Why is the outdoor sensor not connecting?

Check that batteries are inserted properly in both units. Ensure the distance between units is within 100 m and there are no large metal objects or walls blocking the signal. Press the sync button on the indoor unit (if available).

How accurate is the temperature and humidity measurement?

Temperature accuracy is ±1°C, humidity accuracy is ±5% RH under normal conditions. Calibration may drift over time; periodic checks are recommended.

How do I reset the weather station to factory settings?

Remove batteries from both units, wait 30 seconds, then reinsert them. The station will reset and begin searching for the sensor again.

Can I use the weather station without the outdoor sensor?

Yes, the indoor unit will still display indoor temperature, humidity, and time. However, outdoor data and weather forecast features require the sensor.

How does the weather forecast feature work?

The station uses barometric pressure trends to predict weather conditions (sunny, cloudy, rainy, stormy). It is a general guide and not 100% accurate.

Why is the time not displaying correctly?

Ensure the time zone is set correctly. The station may have a manual time setting or auto-sync via a time signal (if supported). Refer to the manual for time adjustment.

How do I clean the weather station?

Use a soft, dry cloth to wipe the display and housing. Avoid water, cleaning agents, and abrasive materials. Do not immerse in water.

USER MANUAL SVD065 JOHNSON

2x1,5V (AAA) Batterie non incluse/ Batteries not included

AVVERTENZE GENERALI

Carefully read the requirements in this manual and keep in a safe place. It contains important instructions on the safety, use and future of your appliance.

This appliance is only for domestic use and must only to be used for the purpose it was specifically designed.

Any other use is considered improper and dangerous.

The manufacturer cannot be held responsible for any damages caused by improper, incorrect and negligent use.

The installation must be carried out according to the manufacturer's instructions.

The manufacturer shall not be held responsible for any damages to people, animals or objects caused by incorrect installation.

The safety of the electrical equipment is only guaranteed if it is connected to an electrical installation equipped with a suitable earthing system in compliance with the current standards on electrical safety.

Do not leave parts of packaging (plastic bags, foam polystyrene, nails, etc) within reach of children or incapacitated people since they are potential sources of danger.

Before connecting the appliance, check that the technical data on the rating label corresponds to those of the main electricity network.

In case of incompatibility between the outlet and the plug, contact a qualified electrician for the necessary adjustments.

Do not use adaptors, multiple plugs and extension leads.

However, if absolutely necessary only use materials that conform to the current safety standards and that are compatible with the appliance and the main electricity network.

On using the appliance for the first time, remove any labels or protective sheets.

If the appliance is equipped with air inlets, make sure they are never blocked not even partially.

The use of any electrical appliance involves the observance of some fundamental rules. In particular:

Do not immerge the appliance in water and do not wet; do not use it near water, in the tub, washbasin or near other recipients with liquids. If the appliance should accidentally fall in water, DO NOT try to touch it but immediately disconnect the plug from the mains power.

Then bring it to an authorised service centre for the necessary controls.

During use, the appliance must be kept away from any inflammable objects or substances or explosives.

Do not touch the appliance with wet hands or feet.

Do not use the appliance with bare feet.

Do not pull on the power cord or on the appliance itself to disconnect the plug from the power outlet.

Do not leave the appliance exposed to atmospheric agents (sun, rain...).

Keep the appliance out of reach of children or incapacitated people and do not let them use it.

Disconnect the plug from the power outlet when the ap-

pliance is not being used and before carrying out any cleaning or maintenance.

The power cord must be completely unwound to prevent it from overheating.

The power cord must be kept away from heat sources and/or sharp edges.

If power cord is damaged, have it replaced by qualified personnel.

Switch off and contact a qualified technician if the appliance should breakdown and/or not function properly.

Any tampering or interventions executed by unqualified people will cancel the guarantee.

Use a soft and non-abrasive cloth to clean the appliance.

When the appliance is unserviceable and must be eliminated, remove its cords and dispose of it at an authorised disposal centre in order to protect the environment.

- Warranty does not cover any glass parts of the product.

ATTENTION:

The damages of the power supply cord, originate by the wear aren't covered by guarantee; the repair will be in charge to the owner.

ATTENTION:

Warranty does not cover any plastic parts of the product.

ATTENTION:

If the need should arise to take or send the appliance to an authorised service centre, make sure to clean all its parts thoroughly.

For hygienic purposes, the service centre shall reject appliances that are not perfectly clean on the outside or inside without making any controls or repairs.

The symbol 🏠 on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

FUNCTION INTRODUCTION:

Clock with Perpetual calendar

Alarm with 3-minute snooze function

Temperature display in °C/F

1. Insert 2 AAA size 1,5V batteries into the battery holder, then show normal mode and play a piece of song.

2. Under normal mode, press MODE to go into the following function state:

12hr/24hr - Alarm Birthday remind

Count down Timer Return

1. Under above setting mode. Press UP/DOWN key to adjust values, hold the key to increase values quickly.

2. Under 12hr/24hr mode, press UP to shift 12hr/24hr format.

3. Under alarm state, there will have “ALARM” sign. Press SET and UP/DOWN to set alarm time and choose alarm music among 7 different famous world songs and 2 different BiBi voices. Press SET to confirm the adjustment. Press SET again to close alarm function with icon “____” displaying.

4. Alarm voice will last one minute when alarm time setting is coming if open snooze function, alarm voice will ring 4 times for 3 minutes.

5. Under birthday remind state, press SET to enter into and time setting, press UP/DOWN key to adjust values and then press SET to confirm setting when birthday remind setting is on, it will play birthday song for five minutes.

6. Count down timer mode. There will show “TIMER” sign. Press SET to set countdown with time range in 23:59–00:00. When time goes to “00:00”, alarm voice will last one minute and “00:00” always glitter.
7. Under normal mode, when display "ALARM" sign, press UP key to turn on/off snooze function. There will have "SNOOZE" sign.
8. Under normal mode, press DOWN key to turn on/off music function when display the music sign “---”. 6 songs will be played circularly.
9. Under normal mode, press SET to select temperature unit °C/F.
10. It will return the normal mode without pressing any key for one minute during above processes.

Please press RESET key, if there is erroneous display.

GARANZIA

The validity of the guarantee starts from the purchasing date certified by the seller's stamp and expires at the end of the indicated period, even when the device has not been used. The guarantee covers all substitutions or repairs due to material or manufacturing defects. The guarantee has no validity in case of device tampering or when the defect is due to incorrect or improper use of the same. Substitutions and repair covered by the guarantee are made free of any charge for goods delivered free our service company representative. Only the freight will be at buyer's expense. All replaced parts or devices will become our property.

GARANZIA - GUARANTEE

2 ANNI YEARS

internet: www.johnson.it

e-mail: com @johnson.it

MOD. SVD065

DATA ACQUISTO

PURCHASE DATE

DATA RIPARAZIONE

REPARE DATE

TIMBRO CENTRO ASSISTENZA

AFTER SALES SERVICE

CENTER STAMP

MOD. SVD065

This certificate of guarantee has to be dulyfilled in to be valid