SG50T12AVH00 - Water heater GE - Free user manual and instructions
Find the device manual for free SG50T12AVH00 GE in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Electric Water Heater |
| Brand | GE |
| Model | SG50T12AVH00 |
| Tank Capacity | 50 Gallons |
| Voltage | 240 V |
| Wattage | 4500 W |
| Dimensions (H x W x D) | 60.5 x 22.4 x 22.4 inches |
| Weight (Empty) | 150 lbs |
| Energy Factor | 0.94 |
| First Hour Rating | 62 Gallons |
| Recovery Rate | 21 GPH at 90°F rise |
| Temperature Setting Range | 90°F to 150°F (adjustable) |
| Heating Elements | Two copper elements |
| Anode Rod | Powered anode rod |
| Temperature and Pressure Relief Valve | Included (factory installed) |
| Water Connections | 3/4 inch NPT |
| Installation Type | Indoor floor or platform |
| Warranty | 6 years tank, 4 years parts |
| Maintenance | Annual flushing and anode check |
| Safety Features | Thermal cut-off, pressure relief, leak detection |
| Smart Features | None (standard electric) |
Frequently Asked Questions - SG50T12AVH00 GE
How do I set the temperature on my GE SG50T12AVH00 water heater?
Locate the temperature dial on the upper thermostat. Use a flathead screwdriver to adjust to your desired temperature, typically 120°F for energy savings and safety. Always turn off power before accessing the thermostat panel.
Why is my water heater making a popping noise?
Popping noises are usually caused by sediment buildup at the bottom of the tank. To resolve, flush the tank annually by draining a few gallons through the drain valve to remove sediment.
How often should I replace the anode rod?
GE recommends inspecting the anode rod every 2-3 years and replacing it when more than 50% depleted. A powered anode rod may last longer. Replacement helps prevent tank corrosion.
What should I do if water leaks from the pressure relief valve?
If water drips from the T&P valve, it may be due to high water pressure or thermal expansion. First, check water pressure (should be below 80 psi). If normal, the valve may need replacement. Do not plug the valve.
Can I install this water heater in a mobile home?
Yes, the SG50T12AVH00 is suitable for manufactured homes. Ensure it is installed on a non-combustible floor and meets local codes. Use earthquake straps if required.
How do I reset the high-temperature limit switch?
Turn off power to the heater. Remove the upper access panel and locate the red reset button on the limit switch. Press it firmly. If it trips again, have a professional diagnose the issue.
Is the water heater energy efficient?
Yes, with an Energy Factor of 0.94, it meets ENERGY STAR standards. The low standby heat loss insulation helps maintain water temperature efficiently.
What size breaker do I need?
For a 4500W 240V unit, use a 30-amp double-pole breaker with 10 AWG copper wire. Always consult the manual and local codes.
How do I flush the sediment from the tank?
Turn off power, then attach a hose to the drain valve. Open the valve and a hot water tap to allow flow. Drain until water runs clear. Close valve, remove hose, turn on water and power. Annual flushing extends heater life.
Where can I find replacement parts for my GE water heater?
Replacement parts like thermostats, elements, and anode rods are available at GE Appliances parts website or authorized dealers. Use your model number SG50T12AVH00 for exact fit.
User questions about SG50T12AVH00 GE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water heater in PDF format for free! Find your manual SG50T12AVH00 - GE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SG50T12AVH00 by GE.