Turbo Steam 6062 - Iron SUNBEAM - Free user manual and instructions

Type de produit	Steam Iron
Marque	Sunbeam
Modèle	Turbo Steam 6062
Puissance	1500 W
Tension	120 V
Fréquence	60 Hz
Type de semelle	Non-stick stainless steel
Capacité du réservoir	300 ml
Débit de vapeur max	30 g/min
Fonction spray	Yes
Fonction auto-nettoyage	Yes
Anti-goutte	Yes
Arrêt automatique	Yes, after 30 seconds horizontal / 8 minutes vertical
Longueur du cordon	2.4 m (8 ft)
Dimensions (L x l x H)	31 x 13.5 x 15.2 cm (12.2 x 5.3 x 6.0 in)
Poids	1.32 kg (2.9 lbs)
Matériau	Plastic and stainless steel
Couleur	White/Blue
Entretien	Descaling every 1-3 months depending on water hardness
Garantie	2 years

Frequently Asked Questions - Turbo Steam 6062 SUNBEAM

How do I refill the water tank?

Ensure the iron is unplugged and cool. Open the water tank cover and pour water using a measuring cup, avoiding overfilling. Close the cover securely before plugging in.

Can I use tap water in my Sunbeam Turbo Steam 6062?

Yes, but for optimal performance and to prevent mineral buildup, it is recommended to use distilled or demineralized water, especially in hard water areas.

What does the auto shut-off feature do?

The iron automatically turns off if left unattended: after 30 seconds when placed horizontally on the soleplate, or after 8 minutes when left upright on the heel.

Why is my iron not producing steam?

Check that the water tank is filled, the temperature dial is set to a steam-appropriate setting (above ••), and the steam button is activated. If still no steam, try the self-clean function.

How do I clean the soleplate?

Allow the iron to cool completely. Use a damp cloth with mild soap to wipe the soleplate. Avoid abrasive cleaners. For stubborn residue, use a solution of vinegar and water.

How often should I descale the iron?

Descaling frequency depends on water hardness. As a general rule, perform the self-clean function every 1-3 months to remove mineral deposits from the steam chamber.

What does the self-clean function do?

The self-clean function flushes out loose mineral deposits from the steam chamber. Fill the tank, set the temperature to high, unplug the iron, hold it over a sink, and press the self-clean button until water runs clear.

Can I iron delicate fabrics?

Yes. Use the temperature dial to select the appropriate setting for the fabric (e.g., low for synthetics, medium for wool, high for cotton/linen). Always test on a hidden area first.

How do I store the iron after use?

Unplug the iron and allow it to cool completely. Empty the water tank to prevent leaks and mineral buildup. Store upright on the heel in a dry place.

What should I do if the iron leaks water?

Leaking may occur if the temperature is too low for steam or if the tank is overfilled. Ensure the temperature dial is set correctly (above •• for steam). If leaking persists, dry the soleplate and run the self-clean cycle.

USER MANUAL Turbo Steam 6062 SUNBEAM

Black and white photo of a Sunbeam air iron with visible branding, placed on a surface (no text or symbols on the device itself)

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

READ ALL INSTRUCTIONS BEFORE USE

• Use iron only for its intended use.
• To protect against risk of electric shock, do not immerse the iron in water or other liquids
• The iron should always be set to the off position with the fabric setting button before plugging and unplugging. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
• Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing.
• Always disconnect iron from electrical outlet when filling with water or emptying and when not in use.
• Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to an authorized service center for examination and/or repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.
• Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while plugged in or turned on or on an ironing board.
• Burns can occur from touching hot metal parts, hot water or steam. Use caution you turn a steam iron upside down – there may be hot water in the reservoir.
• If the iron is not operating normally, disconnect from the power supply and have the iron serviced by an authorized service center. Or call Customer Service at 800-458-8407.
• Your SUNBEAM iron is designed to rest on the heel rest. Do not leave the iron unattended. Do not set the iron on an unprotected surface, even if it is on its heel rest.

SPECIAL INSTRUCTIONS

• This is a 1500-Watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
• If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the extension cord so that it cannot be pulled or tripped over.

FOR PRODUCTS PURCHASED IN THE UNITED STATES AND CANADA

To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wide than the other). This plug fits a polarized outlet only one way; if the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attenu to defeat this safety feature.

SAVE THESE INSTRUCTIONS

IRONING GUIDE

FABRIC	SUGGESTED FABRIC SELECTSTEAM SETTING	DIAL SETTING	IRONINGRECOMMENDATIONS
Acrylic Off (	Dry)	Synthetic	Iron garment inAcetate side out
Acetate Off (	Dry))	Synthetic	Iron garment inside out while still damp.
Polyester Off (	Dry)	Synthetic	Iron garment inside out while still damp.
Rayon Off (	Dry)	Synthetic	Iron garment inside out.
Silk Off (	Dry)	Silk	Iron garment inside out. Use an ironing cloth* to prevent shine marks.
Viscose Off (	Dry)	Silk	Mainly dry iron; steam may be used under garment manufacturer's instructions.
Nylon Off (	Dry)	Silk	Iron garment inside out while still damp.
Wool	Steam Wool		Iron garment inside out or use an ironing cloth.*
Wool Blends	Steam Wool		Iron garment inside out or use an ironing cloth.*
Cotton Blends	Steam	Cotton	Follow garment manufacturer's instructions. Use setting for the fiber requiringhe lowest setting.
Corduroy	Steam	Cotton	Iron garment inside out or use an ironing cloth* and then brush the garment with your hand to raise the texture of the fabric.
Cotton Steam	Cotton		Iron dark fabrics inside out to prevent shine marks.
Linen	Steam	Linen	Iron garment inside out or use an ironing cloth* to prevent shine marks (especially on dark fabrics).
Denim	Steam	Linen	Use the Shot of Steam® feature for deeper penetration to remove wrinkles.

*An ironing cloth is a cotton, dry-cleaned cloth that you place over the garment you are ironing to prevent fabric from looking shiny.
Note: Some fabrics may require more steam than others. Your iron will automatically adjust steam as needed.

FEATURES OF YOUR TURBO STEAM™ IRON

1. Covered Water Fill Hole
2. Wait / Ready Light
3. Electronic / Digital Display
4. Auto-Off Indicator
5. Steam On/Off Buttons
6. Fabric Select Buttons
7. Turbo Steam™ Button
8. Shot of Steam® Button / Vertical Steam Button
9. Soft Grip Handle
10. Cord Lock ^TM Feature
11. Self-Clean Button
12. Translucent Water Reservoir with Max/Refill Lines
13. Soleplate
14. Storage Strip™ Indicator

Figure A

Toggle up to desired fabric and wait for red light to turn green.

TO FILL THE WATER RESERVOIR

1. Make sure the iron is unplugged.
2. Lift the Water Fill Hole Cover.
3. Fill water cup with water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum fill level.

WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries.

SELECTING FABRIC SETTINGS

To select a fabric setting, press the Fabric Select buttons (▲▼) until the desired fabric lights up (Figure A). The Wait/Ready light will change from red to green when the iron is ready to use.

NOTE: When using the Steam Function, the iron will automatically adjust the steam to match the fabric selection.

DRY IRONING

1. Plug the cord into a 120-Volt AC outlet.
2. Select Fabric Setting.
3. Press the Steam Off button.

NOTE: While in the Steam Off (Dry) setting, you may still use the Shot of Steam® feature or Turbo Steam™ feature. Please make sure the water reservoir is at least full to the Refill line.

TIP: Refer to the Ironing Guide for the recommended setting for your fabric.

STEAM IRONING

1. Follow the instructions for "To fill the Water Reservoir".
2. Plug the cord into a 120-Volt AC outlet.
3. Select Fabric Setting.
4. When the green ready light turns on press the Steam On button.

TIP: Refer to the Ironing Guide for the recommended setting for your fabric.

The Turbo Steam™ feature allows the iron to function as a power garment steamer. It can provide continuous pulsating steam for up 10 minutes and can be used horizontally or vertically. Turbo Steam ideal for steaming wrinkles out of delicate clothing, hanging garme and draperies.

To use Turbo Steam™:

1. Fill the water reservoir to the max fill line.
2. Hold the iron, either horizontally and iron normally or Ivertically, close to but not touching the fabric or garment to be steamed.
3. Using your free hand, keep the fabric pulled tight.
4. Press the Turbo Steam™ button once to turn the Turbo Steam feature on. Press the button again to turn it off. Turbo Steam not turn on while in SYN or SILK fabric settings.
5. The Turbo Steam ^TM feature will start once the iron reaches maximum temperature.

IMPORTANT: The Turbo Steam™ pump action may cause the iron to vibrate slightly during use.

SHOT OF STEAM® / VERTICAL STEAM FEATURE

The Shot of Steam®/ Vertical Steam feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reservoir must be above the Refill line.

To use the Shot of Steam® Vertical Steam Feature:

Place the iron on top of the wrinkle and press the Shot of Steam button each time you would like an extra burst of steam. The Sho of Steam® feature may be used continuously with just a short pause between shots in both the horizontal and vertical position.

WARNING: To prevent the risk of burns, keep your hand away from the area being steamed.

WARNING: DO NOT steam garments while wearing them; this may result in injuries.

MOTION SMART® AUTO-OFF FEATURE

When the iron is plugged in, the Off Indicator will blink, indicating there is power to the iron.

If you leave the iron:

- In a horizontal position without moving it, or accidentally tip the iron over, it will automatically stop heating after 30 seconds. The Off Indicator will blink to let you know that the iron has stopped heating.

- In a vertical position (on its heel rest) without moving it, the iron will automatically turn off after 15 minutes The Off Indicator will blink to let you know that the iron has stopped heating.

To reset the iron:

- Move the iron back and forth. The Off Light will stop blinking and the iron will start heating again.

IMPORTANT: The Off Indicator will continue to blink for 5 minutes after the auto-off has activated. The iron w then turn off completely and no lights will be displayed. re-activate the iron press the ▲or ▼Fabric Select buttons.

WARNING: The Motion Smart® Auto-Off is a safety feature, not a recommended means for turning your iron off. See “Caring for Your Iron After Use” for information on turning off your iron and storing it safely between use

STORAGE STRIP™ INDICATOR

The Storage Strip™ indicator is an easy way to see when the iron is cool enough to store.

To use the Storage Strip™ Indicator:

Turn iron on. In approximately 3 minutes, the Storage Strip ^™ indicator will turn from black to red, indicating that the iron is too hot to store. When the iron is turned off, it will take the iron approximately 55-65 minutes for the Storage Strip ^™ indicator to turn from red to black, indicating that the iron is cool enough to store.

CAUTION: The Storage Strip ^™ indicator should only be used as a guideline. The iron should always be handled and stored with care.

CORD LOCK™ FEATURE

Cord Lock ^™ Feature locks in the left of right position to keep the cord out of your way and off your clothes.

ANTI-CALCIUM SYSTEM

The Anti-Calcium System is a permanent system located inside the water reservoir. This system removes calcium from the water and reduces calcium build-up on the sole-plate.

DRIP-FREE

Produces steam without any dripping, spitting, or leaking through the soleplate, even at low temperatures.

EMPTY WATER MODE

When the water in the reservoir is low, the water-level sensor will emit two short beeps then one longer beep. The iron will automatically switch to Steam OFF mode, and the Steam LED light will turn off.

1. To refill and reset the sensor, fill the water reservoir with water, then press either the Turbo Steam ^™ , Shot of Steam ^® or Steam ON button to allow the sensor to find the new water level and reset. Steam ironing can then be resumed.

2. If steam ironing is attempted, but the water reservoir NOT refilled, the sensor will detect this and emit two short beeps followed by one longer beep, and the iron will switch again to Steam OFF mode until refilled.

NOTE: If you do not refill and reset the sensor you may experience excessive noise and vibration.

CARING FOR YOUR IRON AFTER USE

1. Use Fabric Select buttons (▲▼) to scroll to Off position and unplug iron.

WARNING: NEVER yank the power cord when unplugging the iron. This can damage the cord.

Storing Your Iron

1. Allow the iron to cool.

2. If you do not use your iron on a daily basis, empty the water reservoir after each use for a longer iron life. To do so, unplug the iron, turn the iron upside down, open the fill hole cover, and allow water to flow from the fill hole. Shake the iron gently to remove trapped water drops.

3. Loosely loop the power cord around the heel rest and store the iron on its heel rest.

IMPORTANT: Wrapping the cord around the iron too tightly an damage the cord.

MAINTAINING YOUR TURBO STEAM™ IRON

CLEANING THE SOLEPLATE

Clean the soleplate if starch or other residue accumulates.

To clean the Soleplate:

1. Unplug the iron. Allow the iron to cool and then wipe it with a soft, damp cloth.

WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean the soleplate. This will damage the finish.

1. Run the iron over an all-cotton cloth to remove any residue.

USING THE SELF-CLEAN FEATURE

You should use the Self-Clean feature once a month to maintain the optimal performance of your iron.

To use the Self-Clean feature:

1. Fill the water reservoir with tap water to the MAX line.

2. Plug in the iron and press Fabric Select button to Linen. Allow the iron to heat until the Wait/Ready Light turns GREEN.

3. Unplug the iron.

4. Hold the iron over a sink in a horizontal position.

WARNING: Be careful not to touch the iron's hot surfaces.

1. Press the Self-Clean button and hold. Water will begin dripping from the steam vents. Slowly rock the iron side to side and front to back for 30 seconds. When rocking the iron, dip the nose of the iron slightly below the rear of the iron to make certain the water circulates completely.

2. Turn the iron upside down and allow the remaining water to flow out of the fill hole.

3. Dry the soleplate with a towel.

4. Plug in the iron and press Fabric Select button to Linen. Let the iron heat until the button turns GREEN and dry out the iron completely.

5. Press the Fabric Select button to Off. The light will go out, indicating that the iron has turned itself off. Unplug the iron and allow it to cool.

CLEANING THE ANTI-CALCIUM SYSTEM

The Turbo Steam ^™ iron houses an Anti-Calcium filter in the reservoir, which eliminates impurities from the water.

To prolong the efficiency of this filter:

is1. Unplug the iron and allow it to cool.

1. Locate the water cup that accompanied the iron and fill it with water. Add 1 teaspoon of salt to the water and fill the water reservoir with this solution.

2. Leave the solution in thewater reservoir for 15 minutes, then e

3. Fill the water reservoir a second time with the salt water solution and empty it again after 15 minutes.

4. Fill the tank with fresh water to rinse and empty.

The Anti-Calcium System should be cleaned approximately once a month.

IRONING TIPS

• Always read garment labels and follow the manufacturer's ironing instructions.
• Sort the articles to be ironed according to the type of fabric.
• You should first iron garments requiring low temperature (e.g., silks and synthetics) to avoid damaging them with an iron that is too hot.
• If you are unsure of the fabric content of the garment, test a small area, such as a seam or facing, before ironing a visible area. Start with a low temperature and gradually increase the heat to find the best setting.
• When changing the temperature from a high setting to a low setting, allow approximately 5 minutes for the lower temperature to be reached.
• When steam ironing, use long, slow passes over the fabric. This will allow the steam to penetrate the fabric while allowing the heat of the soleplate to dry out the moisture.
• To iron linens, turn garment inside out. Be careful not to use an iron that is too hot because the lining may melt or stick to the soleplate.
• To iron zippers, use an ironing cloth or make sure the zipper is closed and iron over the flap. Never iron directly over an unprotected zipper.
• Use the Ironing Guide to select the best setting and method for the fabric you plan to iron.

1 Year Limited Warranty

Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively "JCS") warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.

What are the limits on JCS's Liability?

JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition.

Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty.

JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.

JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.

Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction.

How to Obtain Warranty Service

In the U.S.A.

If you have any question regarding this warranty or would like to obtain warranty service, please call 1 800-458-8407 and a convenient service center address will be provided to you.

In Canada

If you have any question regarding this warranty or would like to obtain warranty service, please call 1 800-667-8623 and a convenient service center address will be provided to you.

In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please write to our Consumer Service Department.

PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.

PRECAUCIONES IMPORTANTES

For product questions: Jarden Consumer Service

USA : 1.800.458.8407

Canada:1.800.667.8623

www.sunbeam.com

©2007 Sunbeam Products, Inc. doing business as

Jarden Consumer Solutions. All rights reserved.

In the U.S., distributed by Sunbeam, Products, Inc.

doing business as Jarden Consumer Solutions, Boca Raton, FL 33431

In Canada, imported and distributed by Sunbeam Corporation (Canada) Limited, doing business as Jarden Consumer Solutions,

20 Hereford Street, Brampton, Ontario L6Y 0M1.

SPR-092507

Jarden Consumer Service