3310003 - Camera BRESSER - Free user manual and instructions

Product Type	Digital observation camera (trail camera)
Model	Bresser 3310003
Dimensions	150 x 110 x 75 mm
Weight	270 g
Power Supply	4 or 8 x AA batteries (recommended lithium) or external 6V DC adapter
Image Sensor	5 MP CMOS Colour
Lens	F=2.5, Field of view 55°
IR Illumination Range	Up to 20 m, invisible IR (no flash)
Display	2.0" LCD
Memory Card	SD card up to 32 GB (not included)
Image Resolution	16 MP (interpolated), 12 MP, 8 MP, 5 MP
Video Resolution	1080p Full HD, 720p, VGA
PIR Motion Sensor	120° detection angle, adjustable sensitivity (low/mid/high), trigger time 0.5 s
Operating Temperature	-15°C to +60°C
Storage Temperature	-30°C to +70°C
Waterproof Rating	IP54 (splash and snow resistant)
Operating Modes	Photo, Video, Photo+Video, Timelapse
Battery Life	15-30 days (depending on mode and settings)
Mounting	Belt strap for tree or post
Scope of Delivery	Camera, USB cable, belt

Frequently Asked Questions - 3310003 BRESSER

How do I insert an SD card?

Insert an SD card (8 MB to 32 GB, not included) into the SD card slot until it clicks. Ensure the write-protect switch is unlocked before inserting. Do not insert or remove the card when the power switch is in the ON position. For first use, it is recommended to format the card via the camera.

How do I power on the camera?

Install 4 or 8 AA batteries (recommended alkaline or lithium) following polarity indicators, or connect an external 6V DC adapter. Then slide the ON/TEST/OFF switch to ON to enter monitoring mode, or TEST to adjust settings. The camera screen will turn black after a few seconds in ON mode, indicating power-saving operation.

How do I set the date and time?

In TEST mode, press the MENU button, navigate to Date/Time using ▲/▼, press OK, then set values with ▲/▼ and ▶. Press OK to confirm and MENU to exit. Correct date/time ensures accurate photo stamping and timelapse scheduling.

How do I enable time-lapse mode?

Press MENU and select Mode > Timelapse. Then set the Timelapse interval (15 sec to 30 min) and optionally the Monitoring Period (start and stop time). Make sure Date/Time is set correctly. The camera will automatically create a video from the interval images.

How do I play back photos and videos?

In TEST mode, press the PLAYBACK button. Use ▶/◀ to navigate files. To view details, press MENU for options like View Date/Time, Protect, Delete One, Delete All, or Format the SD card. Press PLAYBACK again to exit.

How do I connect the camera to a computer?

Use the included USB cable to connect the camera's Mini USB port to a computer. The camera automatically switches to USB mode and the SD card appears as a removable drive. You can then transfer files. Ensure the camera is powered on (TEST or ON mode) during connection.

How do I connect to a TV?

Use an AV cable (not included) to connect the camera's TV-Out connector to a TV. After connection, the camera's interface appears on the TV screen and the camera LCD turns black. Playback and menu navigation work as usual.

How do I reset the password?

If you forget your password, use the universal password: 1111. To set or change a password, go to MENU > Password and follow prompts. Use ◀/▶ to navigate digits and OK to confirm.

How do I delete files?

In playback mode, select a file with ▶/◀, press MENU, choose Delete One (single) or Delete All (all files). Confirm with OK. Deleted files cannot be restored. To erase all data, format the SD card via Format in the settings.

How do I clean and maintain the camera?

Use a soft, dry cloth to clean the camera body and lens. Do not use solvents or abrasive cleaners. Remove batteries if not used for a long time. Store in a dry place between -30°C and +70°C. The camera is IP54 rated but avoid prolonged exposure to heavy rain.

USER MANUAL 3310003 BRESSER

Close-up of a camouflaged tactical device with visible internal components and no text or symbols

BEDIENUNGSANLEITUNG

INSTRUCTION MANUAL

BRESSER

Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.
FR Vous souhaitez un mode d'emploi détaillé pour ce produit dans une langue spécifique ? Alors consultez notre site Internet à l'aide du lien suivant (code QR) pour voir les versions disponibles.
¿Desearía recibir unas instrucciones de uso completas sobre este producto en un idioma determinado? Entonces visite nuestra página web utilizando el siguiente enlace (código QR) para ver las versiones disponibles.
DK ∅nsker du en udførlig vejledning til dette produkt på et bestemt sprog? Så besøg vores website ved hjælp af følgen-de link (QR-kode) for tilgængelige versioner.
Вам требуется подробная инструкция на это изделие на определенном языке? Проверьте наличие соответствующей версии инструкции, посетив наш сайт по этой ссылке (QR-код).

MANUAL DOWNLOAD:

Close-up of a camouflage camera module with attached cable and connector (no visible text or symbols)

Close-up of a cylindrical mechanical component with internal cavities and mounting holes (no visible text or symbols)

Standort

About this Instruction Manual

Please read the safety instructions in this manual carefully. To avoid damage to the unit and the risk of injury, only use this product as described in the manual.

Keep the instruction manual handy so that you can easily look up information on all the functions.

General Warnings

This device contains electronic components which operate via a power source (power supply and/or batteries). Only

use the device as described in the manual, or you run the risk of an electric shock.

Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Empty or damaged batteries could cause burns if they come into contact with the skin. If necessary, wear adequate gloves for protection.

! ATTENTION!

Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary. Do not expose the device to temperatures above 60°C.

Do not expose the device to high temperatures. Use only the supplied power supply or the recommended batteries. Do not short-circuit the device or batteries or throw them into a fire! Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.

Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or

with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

EC Declaration of Conformity

CE Bresser GmbH has issued a "Declaration of Conformity" in accordance with applicable guidelines and corresponding standards. The full text of the EU declaration of conformity is available at the following internet address:

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.

Do not dispose of electronic devices in the household garbage! As per Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.

In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in the normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. Disposal in domestic waste violates the Battery Directive.

Batteries that contain toxins are marked with a sign and a chemical symbol. "Cd" = cadmium, "Hg" = mercury, "Pb" = lead.

Cd^1Hg^2Pb^3

^1 battery contains cadmium
^2 battery contains mercury
^3 battery contains lead

Instructions

General Description

This digital observation camera, with invisible IR illumination, works fully automatically. The specific region of interest (ROI) is monitored by a high sensitive 120° Passive Infrared (PIR) motion sensor and can be triggered by the slightest movement of either human or animal thus leading to automatic exposure of high quality pictures (up to 16MP interpolated) or recording of video clips (Full HD) according to default settings or preset customer settings. Colour photos and videos are possible when sufficient light is available. In darkness the integrated infrared LEDs illuminate the region of interest while the camera photographs (monochrome). It's novel patented IR illumination is not visible to animals and humans and has a range of up to 20 meters.

The camera is water and snow resistant thus being ideal for outdoor use. Furthermore, it can be used as a portable digital camera.

Intended use

This surveillance camera is used for monitoring objects or places (eg rooms, door and entrance areas, driveways and wildlife, watching at feeding grounds, the feeding place or deer crossing) with photo or video.

The camera is waterproof (IP54 rating) and thus not only suitable for indoor surveillance, but also for mounting in a protected spot outside. Through motion, the integrated PIR sensor triggers a photo or video that is stored on a memory card. If the ambient light is too weak, the surveillance camera automatically turns on the built-in infrared lighting and the camera turns for better sensitivity into b / w mode. The camera is powered by batteries. For stationary surveillance the camera can also be powered by an AC adapter*. However, the network device* must be protected from moisture and humidity. The surveillance camera is designed exclusively for use in private households. Any other use or modification of the camera is considered improper use and could give rise to considerable dangers. The manufacturer is not liable for damage caused by improper use or incorrect operation.

Important Safety Instructions!

• Please install batteries according to polarity displayed.
• For camera operation an SD-card* (8 MB to 32 GB) is necessary.
• Please unlock the write-protection function before inserting the SD-card.
• Do not insert or remove the SD-card* when the power switch is at the ON position.
• When first in use it is recommended to format the SD-card via the camera.

Scope of delivery

① Digital camera ② USB cable ③ Belt

Close-up of a camouflage camera module with attached cable and connector (no visible text or symbols)

Camera I/O Interfaces

The camera has the following I/O interfaces: Mini USB connector, SD-card* slot, TV output and external DC power connector. There is a small hole in the battery compartment where one can attach a lock for theft-protection.

*not included

Power Supply

The observation camera operates on 6V DC voltage. Power can be supplied using batteries* (4 or 8 x AA batteries) or via an external power adapter*.

Battery Operation

Release the casing latch (6) and open the observation camera. Open the battery compartment door (16). Insert 4 or 8 AA batteries* into the battery compartment. Ensure that the poles of the batteries (+/-) have been correctly positioned, as indicated in the battery compartment.

Note: We recommend using high-quality alkaline or lithium batteries. The battery charge is shown by the battery icon at the bottom of the preview and navigation screen.

ATTENTION!

If you are not using the observation camera, remove the batteries from the battery compartment or disconnect the camera from the external power supply. Remove run-down batteries from the wildlife camera immediately.

Operation via a Power Adapter\*

Use only the correct adapter with a suitable jack and the

BRESSER

correct operating voltage for the external power supply (AC 100V-240V/50-60HZ). When used in outdoor areas, this should be weatherproof. When setting up the camera, take particular care with an external power supply that the connection points also do not come into contact with water while in operation. When not in use, disconnect the camera from the power supply.

ATTENTION!

The manufacturer accepts no liability or guarantee for damage caused by improperly used adapters or the use of the incorrect operating voltage.

1. Operation indicator
2. (IR) Infrared illumination
3. Camera lens
4. PIR (Passive Infrared motion sensor)
5. Buckle
6. Casing latch / hasp
7. Connection for external power supply 6V DC
8. Tripod thread 1/4"
9. LCD Display
10. Direction keys
11. On/Off switch and TEST Mode (for camera settings)
12. Menu, Mode and Playback buttons

13. SD-card slot (for SD-cards up to 32 GB)

14. TV-Out connector

15. USB connector
16. Battery compartment door
17. Eyelet for a lock*
18. Battery compartment

Using an SD memory card\*

You will require an SD memory card* (up to 32 GB), in order to be able to save images or videos. Insert the SD memory card into the SD card slot (13) until it snaps into place with a faint click. To remove the SD card, press once briefly

on the card in the slot. The card will spring out of the slot with a faint click and can be taken out.

Initial operation

○ ON ○ TEST ○ OFF

After the power supply has been established (via batteries or mains adapter) and an SD memory card* has been inserted, the observation camera is ready for operation. Switch on using the "ON/TEST/OFF" switch (11), which can be reached when the camera body is open.

*not included

OFF: To turn the camera off

TEST: Adjust settings, confirm, preview, playback

ON: To enter monitoring mode. The camera takes photos and videos according to your settings.

First, set the slide button to "TEST". The camera is now on, all functions and parameters can now be set. After you have made the settings, you can set the slide button to "ON". The camera screen turns black and the operation indicator blinks. After 5 to 10 seconds the camera starts operating in power save mode.

Menu Navigation

1. Press the "MODE" button to switch between photo and video mode.
2. Press the "MENU" button to display the settings for the currently active mode.
3. Press the ▲ ▼ and ▶ buttons to navigate through the menus.
4. Press the "OK" button to make a selection.
5. Press the "PLAYBACK" button to play back recorded photos or videos. Press the "PLAYBACK" button again to exit the playback mode.

Mode switching

Press the "MODE" button to switch between photo and video mode. With the "Menu" button you can also change the mode, here you can also select "Photo+Video" and "Timelapse".

1. Press the "Menu" button. Mode is already selected.
2. Press the "OK" button.
3. Press the ▲ keys to select a mode and press "OK" to switch to the mode.
4. Move the "ON/TEST/OFF" switch to "ON" to start regular operation of the camera.
5. Photo+Video mode records a photo first and then a video.
6. The Timelapse mode takes photos at certain intervals and creates a video from them.

Camera display icons

After you turn the camera on (power switch in the "ON" or "TEST" position), the recording information is displayed on the monitor.

1. Photo Mode
2. Image resolution
3. Number of photos to take (depending on storage space)
4. SD card display
5. Video Mode
6. White balance display
7. Video resolution
8. Remaining recording time (depending on storage space)
9. Battery level indicator

Close-up of a mechanical component with circular holes and rectangular cutouts (no visible text or symbols)

Location

1. Use the mounting strap to attach the camera to a tree, for example.
2. Before monitoring, please set functions and parameters in photo/video mode, then press the slide button to "ON". 5-10 seconds later, the camera will start normal operation in observation mode.

Note:

Please make sure that the camera is facing the target area. The maximum distance of the IR lights is 20 meters. Avoid direct backlighting. Therefore, position the camera so that you can adjust the camera direction to north or that the camera is in shadow.

Respect privacy!

The device is intended for your personal use.

Respect others privacy - do not use the device to look into other peoples homes or buildings, public spaces, along walking and hiking trails or on heavily frequented places.

Set password

Press the "MENU" button. Under "Password" you can now activate the password query and define a password. Use the □ or □keys to navigate between the numbers. If you have forgotten your password, use the Universal password: 1111.

Set date and time

a) Press the "MENU" button to enter the setting menu.
b) Press ▲ or ▼ to select the menu item "Date/Time".
c) Press OK to confirm the selection and enter the sub-menu.
d) Set the date and time with the buttons ▲/ ▼and ↗. □
e) Press "OK" to confirm.
f) Press "MENU" to exit the settings menu.

Triggering the camera manually

In Test mode it is possible to take photos or record videos

*not included

manually by pressing the "OK" button. Pressing the "OK" button again stops the video recording.

Enable Timelapse

Press the Menu button and select Mode > Timelapse. The time-lapse function is now active.

Timer setting

The "Monitoring period (Timer setting)" is only possible with the Timelapse function active.

If this function is activated, a video is automatically created from timelapse images within your specified time frame. Time-lapse interval and recording time can be set individually. Make sure that "Date/Time" is set correctly.

Connection to a computer

The camera automatically switches to USB mode when the device is connected to a computer via USB cable. In this case, the SD card* functions as a removable disk drive.

Connection to a TV screen

An AV cable* is required to connect to a TV screen. If the connection is successful, the camera's user interface is displayed on the TV screen and the camera screen turns black.

Format SD-Card

ATTENTION: Formatting deletes all images or videos stored on the SD-card*. Please ensure that you have a back-up of all important data.

a) Press the "PLAYBACK" button to enter playback mode.
b) Press the "MENU" button to enter the setting menu.
c) Press ▲ or ▼ to select the "Formatting" menu item.
d) Press OK to confirm the selection and enter the submenu.
e) Press ▲ or ▼ to select "Yes" or "No".
f) Press "OK" to confirm.
g) Press "MENU" and then select "Exit" to leave.

Deleting photos or videos

a) Press the "PLAYBACK" button to enter playback mode.
b) Press ▶ or ▶ to select an image.
c) Press the "MENU" button to enter the setting menu.
d) Press ▲ or ▼o select the menu item "Delete One".
e) Press "OK" to delete the last selected file (YES/NO).

ATTENTION: After deleting a photo or a video file, the deleted files can't be restored! Furthermore, in order to delete all images and video clips on the SD-card, it is recommended you format the SD-card*.

Settings: Photo / Video Mode

Mode Photo / Video / Photo+	Video / Timelapse
PIR delay time (interval) 2 sec	5 sec, 10 sec, 15 sec, 30 sec, 1 min
PIR Sensitivity middle/low/high
Photo Series 1 / 2 / 3
Video Length 10 sec, 20 sec,	30 sec, 1 min, 2 min, 5 min
Video Size 720P, 1080P, VGA
Photo Size 16 MP, 12 MP, 8 MP, 5 MP
Photo Stamp yes/no
Language Select your language
Date/Time Setting the date and time
Timelapse interval 15 sec, 30 sec, 1 min, 3 min
Monitoring Period Set the start and stop time of the recording.

BRESSER

Serial NO Set camera name
Passworf Set password
Version Display version number
Reset Settings Reset to default settings

Settings: Playback Mode

View Date/Time Displaying the date and time of recording

Protect Protect this file from deletion

Delete One Delete selected file

Delete All Delete all files

Format Format SD-card

Exit Exit playback settings

*not included

Technical Specifications

Image Sensor 5MP CMOS Colour
Lens F = 2.5	FOV (Field of view) = 55°
Range of IR-Illumination	20 Metres
Display 2.0" LCD, integrated
Memory card* SD-card (from	8 MB to 32 GB)
Image Resolution 16MP, 12 MP, 8 MP, 5 MP
Video Resolution 1080p, 720p, VGA
PIR Motion sensor	120°
Range of the Motion sensor	20 m
Sensitivity of the motion sensor	middle/low/high
Trigger Time	0.5 seconds
Operation Temperature	-15°C - +60°C
Storage Temperature	-30°C - +70°C
Timelapse Interval	15 seconds to 30 minutes
Video Length 10 seconds to	5 minutes
Power supply 8 × AA (recommended)*or 4 × AA batteries*
Power Consumption 15 ~ 30	days (4x / 8x AA batteries) Depending on mode and environment.
Mounting with belt
Weight 270 g
Dimensions 150x110x75 mm
Operation Humidity 5% - 90%

Warranty & Service

The regular guarantee period is 2 years and begins on the day of purchase. To benefit from an extended voluntary guarantee period as stated on the gift box, registration on our website is required. You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms. Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions. Alternatively you can also send an email to [e-mail] or leave a message on +49 (0) 28 72 - 80 74-220*. Please always state your name, precise address, a valid phone number and email address, as well as the article number and name.

*Number charged at local rates in Germany (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.