BCEZSH26 - Headphones Be Cool - Free user manual and instructions

Product Type	Bicycle Helmet
Brand	Be Cool
Model	BCEZSH26
Head Circumference	S: 53-55 cm, M: 55-58 cm
Net Weight	0.25 kg
Gross Weight	0.35 kg
Outer Shell Material	Lightweight durable plastic
Inner Padding	Removable, washable padding
Ventilation	Multiple vents with internal air channels
Adjustment System	Rear retention system with adjustable straps
Buckle Type	Quick-release buckle
Lights / Indicators	Front and rear lights with turn signals
Remote Control	Handlebar-mounted remote for indicators
Cleaning Instructions	Hand wash with mild soapy water; no solvents
Storage	Store away from heat >60°C (147°F)
Replacement Interval	Every 4-5 years or after impact
Manufacturing Date	Replace no later than 8 years from production
Warranty	2 years (Austria)
Intended Use	Cycling, e-scooters; not for motor sports
Included Accessories	Helmet, user manual

Frequently Asked Questions - BCEZSH26 Be Cool

How do I properly adjust the helmet straps?

Place the helmet firmly on your head and close the buckle. Tighten the chin strap by holding the buckle and pulling the excess strap through (diagram A). To tighten the rear strap, pull the excess from the back of strap 2, then pull side to side to equalize strap lengths (diagram B). Ensure the helmet sits flat on your head. Check tension by opening your mouth; you should feel the strap pull against your chin.

What is the correct way to clean my Be Cool helmet?

Clean the helmet shell, adjustment ring, and removable inner padding by hand using lukewarm water and a soft cloth with a solvent-free cleaner. Do not use solvents, paints, or stickers as they may damage the helmet. Also clean the sunshades similarly if applicable.

How often should I replace my helmet?

Replace the helmet every 4-5 years from the date of first use, depending on usage and conditions. Even without obvious defects, replace it no later than 8 years after the production date. Also replace immediately after a severe impact.

Can I use this helmet for skiing or snowboarding?

No, this helmet is designed specifically for cycling, e-scooters, and similar non-motorized activities. It is not suitable for climbing, skiing, snowboarding, motorcycling, or high-speed sports and does not provide sufficient protection for those activities.

What should I do if my helmet has been involved in an accident?

If your helmet has been subjected to a severe impact, replace it immediately, even if no damage is visible externally. The helmet is designed to absorb impact energy by deforming, and its protective effect may be compromised.

How do I secure the strap ends after adjustment?

Once the straps are correctly adjusted, secure the protruding ends with the provided strap clip. If the straps are too long, you can cut the ends individually and seal them with a match flame to prevent fraying.

Are the lights and indicators waterproof?

The manual does not specify waterproof ratings. However, you should avoid submerging the helmet. Clean with a damp cloth and store away from moisture. The lights are located on the front and back and are controlled by a handlebar-mounted remote.

Can I paint or apply stickers to my helmet?

No, do not paint or stick anything on the helmet. Harmful substances in paints or adhesives may impair the helmet's stability and protective effect. Use only the original parts.

What size should I choose if my head circumference is between sizes?

Try different sizes and choose the one where the helmet fits snugly yet comfortably. You can also mix and match the thickness of the removable pads to best fit the shape of your head. The available sizes are S (53-55 cm) and M (55-58 cm).

Is the helmet suitable for children?

The manual warns that children should always remove their safety helmet before entering a children's playground. It is not suitable for children when climbing or in activities where there is a risk of entanglement. However, it can be used for cycling if properly fitted.

USER MANUAL BCEZSH26 Be Cool

Black and white photo of a modern climbing helmet with adjustable straps (no text or symbols visible)

HERZLICHEN GLÜCKWUNSCH!

Current operating instructions and other languages

Download current user manuals in various languages via the link www.becool.at/downloads or scan the displayed QR code. Follow the instructions on the website.

BE COOL

Illustration showing two helmet positions: one with a crosshair and head-mounted head, the other with a crossed-out helmet and no crosshair (no text or symbols)

Black and white helmet with visible straps and cutouts, no text or symbols present

CONGRATULATIONS! THANK YOU FOR CHOOSING A PRODUCT FROM BE COOL HAVE DECIDED.

BE COOL

Current operating instructions and other languages

Download the latest operating instructions in various languages via the link www.becool.at/downloads or scan the QR code shown. Follow the instructions on the website.

Current operating instructions and other languages

Download current user manuals in various languages via the link www.becool.at/downloads or scan the displayed QR code. Follow the instructions on the website.

BE COOL

PLEASE READ THE OPERATING INSTRUCTIONS CAREFULLY BEFORE STARTING ASSEMBLY, INSTALLATION, OPERATION OR MAINTENANCE. PROTECT YOURSELF AND OTHERS BY FOLLOWING THE SAFETY INSTRUCTIONS. FAILURE TO FOLLOW INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND/OR VOID THE WARRANTY!

IMPORTANT INFORMATION ON SAFETY, POSITIONING AND ELECTRICAL CONNECTION

WARNING!

A helmet has a limited lifespan and should be replaced as soon as signs of wear are visible. To ensure reliable protection, it is important that the helmet is fitted correctly and worn correctly. Please read the information in these instructions carefully and follow them at all times. Failure to do so may result in serious injury or, in the worst case, even death.

BE COOL

BE COOL

For maximum protection, the following instructions must be observed:

Use:

This helmet is an important piece of protective equipment and is only recommended for the following activities (see Figure 1). This helmet is not suitable for other activities (see Figure 2).

Attention:

Children should always remove their safety helmet before entering a children's playground! This helmet is not suitable for children when they are climbing or taking part in other activities where there is a risk of entanglement or strangulation if the helmet gets caught.

Optimum fit:

• The helmet should not be pulled down too far so as not to impair visibility.
• It should protect the forehead area. The helmet should therefore not be pulled too far over the back of the head.
• The helmet sits correctly when it is horizontal on the head.

To ensure that your helmet offers optimum protection, it must fit correctly. Therefore, try out different sizes and choose the one where the helmet fits snugly yet comfortably (see Figure 3).

BE COOL

Adjusting the straps:

To begin with, it is important to adjust the straps so that they run tightly and comfortably under the ears without touching them. The easy-to-use strap distributors on both sides, which have an optional fixation unit, help with this.

Before first use, the straps must be firmly locked with an audible click after adjustment to prevent unintentional adjustment and to lock into place. When adjusting the chin buckle, which must be closed before each ride, make sure that it is not positioned at the level of the jawbone.

Once the straps have been adjusted, the protruding ends can be secured with the strap clip.

If the straps are too long, it is possible to cut the ends individually and seal them with a match flame to prevent fraying.

Proper handling and care:

• Check the helmet regularly for visible defects.
• Do not modify the helmet or remove any original parts, as this may impair the protective effect.
• Do not use the helmet for purposes other than those for which it is intended.
• Replace the helmet immediately if it has been subjected to a severe impact, as the protective effect can be severely impaired even without visible damage.

BE COOL

- A bicycle helmet should be replaced at least every 4-5 years from the date of first use, depending on the degree of use and operating conditions. Due to unavoidable material fatigue, the helmet should be replaced no later than 8 years after the production date, even if there are no obvious defects.

- Do not paint or stick anything on the helmet, as harmful substances may impair its stability and protective effect.

- The helmet must not be exposed to heat above 60^ C ( 147^ F), as this could impair its protective properties.

- Clean the helmet shell, the adjustment ring and the removable inner padding by hand with lukewarm water, soft cloths and a solvent-free cleaner. This also applies to sunshades.

- Do not store the helmet behind glass, e.g. in a car (glass house effect), or near sources of heat or warmth.

- Only use original spare parts.

- Please contact your waste disposal company for information on the correct disposal of the product.

BE COOL

Limited impact protection:

No helmet can fully protect the wearer from all possible collisions. Its function is to absorb impact energy by partially destroying the shell and inner padding. This damage may not be immediately visible. Therefore, a helmet that has been subjected to a significant impact should be replaced, even if no damage is visible on the outside.

When used correctly, helmets can reduce or prevent many injuries. However, even low-speed accidents can result in forces that can cause serious injury or even death. The materials used in safety helmets are designed to deform on impact and absorb much of the energy. Sometimes this can lead to complete destruction of the material, transferring some of the absorbed forces to the head. In cases where these forces are strong enough, serious injury or death can occur. Since various factors play a role in every accident, it is not possible to predict how or when such injuries might occur.

Helmets are designed to protect against head injuries during normal cycling activities, e-scooters and are not suitable for other activities such as climbing, skiing, snowboarding, motorcycling or high-speed sports such as motorcycle racing or car racing.

BE COOL

Recycling, disposal, declaration of conformity

	RECYCLINGThe packaging materials can be recycled. It is therefore recommended to dispose of them in sorted waste
	DECLARATION OF CONFORMITYWe hereby confirm that this product complies with the essential requirements, regulations and directives of the EU.You can view the detailed declaration of conformity at any time under the following link:https://www.schuss-home.at/downloads

Errors and technical changes excepted.

BE COOL

Product description

Similar to cars, we have now fitted lights and indicators for bicycle helmets, which are located on the back and front of the helmet. The indicators can be switched in the desired direction using a remote control attached to the handlebars.

SCOPE OF DELIVERY

The safety helmet is supplied with:

• 1x safety helmet
  • 1x operating instructions

COMMISSIONING

1. INSTALLATION

1. remove the helmet from the packaging and remove all packaging materials.
   2 Check the safety helmet for possible damage.
2. read the "Operation" section to adjust the helmet correctly.

Operation

1. ADJUST HELMET

The safety helmet you have just purchased will provide protection whether on or off the road. To ensure proper use of this helmet, familiarize yourself with its features, fit and care by reading this manual carefully before wearing your new helmet.

Protection and ventilation:

The outer shell allows the helmet to be rated as one of the lightest helmets while providing excellent durability and integrity. The numerous vents with internal air channels channel air through the helmet and across the forehead for maximum cooling.

Upholstery adjustment:

The helmet must fit correctly to be effective. With a proper fit, the helmet should not slide back and forth or side to side while it is fastened. If the helmet does not fit

BE COOL

with the pads installed, simply remove them and install a different size pad. To ensure the correct fit, you can mix and match the thickness of the pads to best fit the shape of your head.

fastening system:

Rear

A.

Retaining

Front

This safety helmet uses a quick-release buckle that is easy to operate and can be closed and opened without changing the setting. The straps must be tight and evenly tensioned. Place the helmet firmly on your head and close the buckle.

Note which strap is loose. Tighten the loose strap after removing the helmet.

To tighten the chin strap, hold the buckle firmly with one hand. Then pull the excess strap through. (See diagram A).

To tighten the rear strap, pull out the excess strap from the back of strap 2. Hold the helmet firmly with one hand. With the other hand, hold the strap where it runs under your chin. Then pull from side to side to equalize the length of all four straps. (See diagram B)

Pull to equalize the belt lengths

Front

B.

The helmet must sit firmly and flat on your head. (See diagram C). To lower the front of the helmet and cover your forehead, tighten the chin strap and loosen the rear strap. To raise the front, loosen the chin strap and tighten the rear strap.

Illustration showing a person wearing a helmet and another figure with a crossed-out circle (no text or symbols)

To check the correct tension, put the helmet on and close the buckle. Open your mouth. You should feel the strap pull against your chin.

Then try to pull the helmet forwards or backwards. If the helmet slips off, increase the strap tension and check whether thick pads are being used. The helmet should not be able to roll forwards or backwards excessively. It should not be possible to remove the helmet without undoing the buckle.

NOTE: Please check the setting every time this helmet is worn.

BE COOL

Final review

The most important thing is that the helmet sits firmly. If you can move it forwards or backwards, you must tighten the strap adjustment.

The straps should be positioned so that they do not cover the ears and the buckle is not on the chin when correctly fitted.

Buyers should always try different sizes and choose the size that feels secure and comfortable on the head.

It is important that the helmet sits firmly on your head and is put on to provide maximum protection.

All adjustments should be checked each time the helmet is worn to ensure that it is securely fitted at all times.

Caring for your helmet

Only clean the head protection with mild soapy water. The use of solvents, paints or stickers can damage the helmet and render it ineffective in the event of an accident.

Protect your helmet from extreme heat

The helmet will be damaged if it is exposed to temperatures above 150^ . Dark vehicles and storage bags can exceed this temperature on very hot days. Heat damaged helmets will have random deformed areas where the texture appears bubbled and uneven. Damaged helmets should be destroyed and replaced immediately.

Important information

This safety helmet is designed to absorb the energy of an impact through partial destruction or damage. Even if such damage is not visible, the helmet must be replaced if it is involved in an accidental fall.

Unfortunately, some accidents lead to head injuries that cannot be prevented by a helmet. Depending on the type of impact, even very low speeds can lead to serious head injuries or death. Always ride with extreme caution and read this manual thoroughly.

BE COOL

The safety helmet is designed and intended exclusively for use when cycling and other non-motorized sports. It is not intended for use in motor sports or moped riding and does not offer sufficient protection in these cases. No helmet can protect the wearer from all unpredictable impacts. Nevertheless, the helmet must fit well and all straps must be securely fastened to ensure maximum protection.

It is dangerous to modify or remove any original parts of the helmet.

The helmet should not be adapted for the installation of accessories in a way that is not recommended by the manufacturer.

The helmet should be replaced after 3 years from the date of manufacture.

For the disposal of used helmets, please observe the local regulations for the disposal of waste products.

BE COOL

TECHNICAL DATA

Technical information
Dimensions
Product dimensions	S: 53-55 cmM: 55-58 cm
Weight net/gross:	0.25 / 0.35 kg
Contact addresses for further information and service line:	Schuss Home Electronic GmbHScheringgasse 3, A-1140 Vienna Tel:[phone] - 0www.becool.atFB-No.: 23697 4 t / FB-Court: Vienna

BE COOL

WARRANTY

With this quality product from BE COOL, you have made a decision for innovation, durability and reliability.

For this BECOOL appliance we grant a warranty period of 2 years from the date of purchase valid in Austria! If, contrary to expectations, service work is required on your appliance during this period, we hereby guarantee to repair it free of charge (spare parts and labor) or (at Schuss's discretion) to replace the product. If neither repair nor replacement is possible for economic reasons, we reserve the right to issue a current value credit note.

In the case of air conditioners, please always contact the customer hotline as a first step (see sticker on the appliance or the front page of the operating instructions); in the case of fans, please contact your specialist dealer or us directly. Please note that repair work not carried out by an authorized workshop in Austria will immediately invalidate this warranty.

This guarantee does not cover

• We do not accept any liability for consequential damage in the event of improper use
• Repair or replacement of parts due to normal wear and tear
• Damage due to non-compliance with the operating instructions
• Devices that are used - even partially - for commercial purposes
• devices mechanically damaged by external influences (fall, impact, breakage, improper use, etc.) as well as signs of wear and tear of an aesthetic nature.
• Devices that have been handled improperly
• Devices that have not been opened by our authorized service workshop.
• Unfulfilled consumer expectations.
• Damage caused by force majeure, water, lightning, overvoltage.
• Devices where the type designation and/or serial number on the device has been changed, deleted, made illegible or removed.
• services outside our authorized workshops, the transport costs to an authorized workshop or to us and back, as well as the associated risks.

We would like to emphasize that within the warranty period, a lump sum of € 60,- (indexed based on CPI 2010, June 2015) will be charged for operating errors or if no error was detected.

The provision of a warranty service (repair or replacement of the device) does not extend the absolute warranty period of 2 years from the date of purchase.

The 2-year guarantee is only valid on presentation of the proof of purchase (must include the name and address of the dealer and the full name of the appliance) and the corresponding guarantee certificate, on which the appliance type and the serial number (visible on the box and on the back or bottom of the appliance) must be noted! Without the warranty certificate, only the statutory warranty applies!

We expressly point out that the statutory warranty rights are not affected by this guarantee and remain unaffected.

Schuss Home Electronic GmbH and its vicarious agents shall only be liable for damages in the event of gross negligence or intent. Liability for loss of profit, expected but unrealized savings, consequential damages and damages from third party claims is excluded. Damage to or for recorded data is always excluded from the liability for damages.

Congratulations on your choice. We hope you enjoy using your BE COOL appliance!

ADDRESS

Schuss Home Electronic GmbH

A-1140 Vienna, Scheringgasse 3

Tel.: [phone]

This warranty certificate must be handed over to the authorized service workshop together with the appliance in the event of a warranty claim.