IB-1825M-C31 - External hard drive Icy Box - Free user manual and instructions

Product Type	External M.2 NVMe SSD Enclosure
Interface	USB 3.1 (Gen 2) Type-C™ / Type-A (via included adapter)
Supported SSDs	M.2 NVMe PCIe (M-Key) in sizes 2230, 2242, 2260, 2280
Maximum Capacity	Up to 2 TB
Data Transfer Rate	Up to 1000 MB/s (10 Gbit/s)
Material	High-grade aluminum alloy
Write Protection	Yes, hardware switch for read-only mode
LED Indicator	Power (blue) and write protection status
Cooling	Included heatsink and thermal pad
Compatibility	Windows® and macOS®
Power Source	Bus-powered via USB (no external power adapter needed)
Package Contents	Enclosure, USB Type-C to Type-A cable, Type-A to Type-C adapter, thermal pad, heatsink, screwdriver, screws, manual
Supported Host Interfaces	USB 3.1/3.0/2.0 Type-A, USB Type-C, Thunderbolt™ 3 (at USB 3.1 Gen 2 speeds)

Frequently Asked Questions - IB-1825M-C31 Icy Box

What type of SSD is supported by the IB-1825M-C31?

The enclosure supports M.2 NVMe PCIe SSDs with an M-Key only. It does not support SATA or B-Key SSDs.

How do I install an M.2 SSD into the enclosure?

First, remove the PCB and place the M.2 SSD into the socket at a 30° angle, then press down and secure with the included screw. Apply the thermal pad and attach the heatsink. Reinstall the PCB into the housing and close the cover.

Does the IB-1825M-C31 support USB 3.0 or 2.0?

Yes, it is backward compatible with USB 3.0/2.0 ports, but data transfer speeds will be limited to the host interface's maximum (e.g., 5 Gbit/s for USB 3.0).

How do I activate write protection?

Slide the hardware switch on the enclosure to the desired position. The change takes effect after disconnecting and reconnecting the device to the computer.

What does the LED indicator mean?

The LED lights up blue when the device is connected and powered. It remains blue when write protection is active, but data cannot be written to the drive.

Can I use this enclosure with a Thunderbolt 3 port?

Yes, the IB-1825M-C31 works with Thunderbolt™ 3 ports, but the transfer speed will be limited to USB 3.1 Gen 2 speeds (10 Gbit/s).

What operating systems are compatible?

The enclosure supports Windows® and macOS®. Drivers are built-in for both systems.

Why is my SSD not recognized by the computer?

Ensure the SSD is properly installed and the USB cable is connected. New SSDs must be initialized, partitioned, and formatted using disk management tools in Windows or Disk Utility on macOS.

Does the enclosure require an external power supply?

No, it is bus-powered via the USB connection. No external power adapter is needed.

What is the maximum SSD capacity supported?

The IB-1825M-C31 supports M.2 NVMe SSDs up to 2 TB capacity.

USER MANUAL IB-1825M-C31 Icy Box

Exterior view of a gray rectangular electronic device with perforated top and internal ports (no readable text or symbols)

Sicherheitshinweise

Please read carefully the following information to prevent injuries, damage to material and device as well as data loss:

Warning levels

Signal words and safety codes indicate the warning level and provide immediate information in terms of the probability of occurrence as well as the type and severity of the consequences if the measures to prevent hazards are not complied with.

DANGER

Warns of a directly hazardous situation causing death or serious injury.

WARNING

Warns of a potentially hazardous situation that may cause death or serious injury.

CAUTION

Warns of a potentially hazardous situation that may cause minor injury.

IMPORTANT

Warns of a potential situation that may cause material or environmental damage and disrupt operative processes.

1. Risk of electrical shock

WARNING

Contact with parts conducting electricity

Risk of death by electrical shock

• Read the operating instructions prior to use
  • Make sure the device has been de-energised prior to working on it
• Do not remove contact protection panels
• Avoid contact with conducting parts
• Do not bring plug contacts in contact with pointed and metal objects
  • Use in intended environments only
• Operate the device using a power unit meeting the specifications of the type plate only!
• Keep the device/power unit away from humidity, liquid, vapour and dust
• Do not modify the device
• Do not connect the device during thunderstorms
• Approach specialist retailers if you require repairs

2. Hazards during assembly (if intended)

CAUTION

Sharp components

Potential injuries to fingers or hands during assembly (if intended)

• Read the operating instructions prior to assembly
• Avoid coming into contact with sharp edges or pointed components
  • Do not force components together
• Use suitable tools
  • Use potentially enclosed accessories and tools only

3. Hazards caused by a development of heat

IMPORTANT

Insufficient device/power unit ventilation

Overheating and failure of the device/power unit

Safety Information

• Prevent externally heating up components and ensure an exchange of air
• Do not cover the fan outlet and passive cooling elements
• Avoid direct sunlight on the device/power unit
  • Guarantee sufficient ambient air for the device/power unit
• Do not place objects on the device/power unit

4. Hazards caused by very small parts and packaging

WARNING

Risk of suffocation

Risk of death by suffocation or swallowing

• Keep small parts and accessories away from children
• Store/dispose of plastic bags and packaging in an area that is inaccessible to children
• Do not hand over small parts and packaging to children

5. Potential data loss

IMPORTANT

Data lost during commissioning

Potentially irreversible data loss

• Always comply with the information in the operating instructions/quick installation guide
- Exclusively use the product once the specifications have been met
• Back up data prior to commissioning
• Back up data prior to connecting new hardware
• Use accessories enclosed with the product

6. Cleaning the device

IMPORTANT

Harmful cleaning agents

Scratches, discolouration, damage caused by moisture or short circuit in the device

• Disconnect the device prior to cleaning
• Aggressive or intense cleaning agents and solvents are unsuitable
  • Make sure there is no residual moisture after cleaning
  • We recommend cleaning devices using a dry, anti-static cloth

7. Disposing of the device

IMPORTANT

Environmental pollution, unsuitable for recycling

Potential environmental pollution caused by components, recycling circle interrupted

This icon on product and packaging indicates that this product must not be disposed of as part of domestic waste. In compliance with the Waste Electrical and Electronic Equipment Directive (WEEE) this electrical device and potentially included batteries must not be disposed of in conventional, domestic waste or recycling waste. If you would like to dispose of this product and potentially included batteries, please return it to the retailer or your local waste disposal and recycling point.

If you have any questions, please do not hesitate to contact our support at [e-mail] or visit our website at www.raidsonic.de.

Manual IB-1825M-C31

1. Packing content

• 1x IB-1825M-C31 (drive not included)
- 1x Type-C ^TM to Type-A cable
- 1x Type-A to Type-C ^TM adapter
- 1x Silicon thermal pad
- 1x Heat sink
- 1x Screw driver
- 1x Set of screws
- 1x Manual

2. Product overview

123

1. Switch for write protection activation
2. LED for power and write protection status
3. USB 3.1 (Gen2) Type-C ^TM interface to host connection

Please note the following information about the compatibility of USB Type-C ^™ enclosures and adapters, including this device!

• Your host computer must have a USB Type C ^TM or Type-A interface.
• The IB-1825M-C31 also works with computers and notebooks with USB 3.0/2.0/1.1 Type-A interfaces by using the enclosed USB-Type-C™ to type-A cable.
• The enclosure also works on devices with a Thunderbolt ^TM 3 interface with the transfer rate of up to 10 Gbit/s specified by USB 3.1 (Gen 2).
• The Type-C ^TM or Type-A plug can be connected with USB 3.0 or 2.0 standard in some notebooks and computers. The enclosure only supplies the full data transfer rate of up to 10 Gbit/s to USB 3.1 (Gen 2) interfaces.
• The following operating systems are supported: Windows ^ , macOS ^

Manual IB-1825M-C31

Attention: This device supports only M.2 PCIe NVMe SSDs with M.2 M-Key!

External USB Type-C ^™ Enclosure for M.2 NVMe SSD

With the help of the external USB 3.1 Type-C™ enclosure IB-1825M-C31 you can take one NVMe SSD with you quickly and easily. It allows access to M.2 SSDs of up to 2 TB no matter to which host you connect it. The IB-1825M-C31 is compatible with M.2 cards of 30, 42, 60 and 80mm length, suitable for a variety of applications such as high-speed storage, cloning a drive or running a mobile operating system.

With the IB-1825M-C31, sensitive data can now be protected against changes and released again via a switch. The switch on the IB-1825M-C31 can be moved to the desired position. Click - Safe.

3. Key features

• High-grade aluminium enclosure with Mac Pro look
- Interface to host computer: USB 3.1 (Gen 2) Type-C™ and Type-A
• Data transfer rates of up to 1000 MB/s
• M-Key socket for NVMe SSDs, 22 x 30/42/60/80 mm
- Thermal pad
• Supports Windows ^® and macOS ^®

Manual IB-1825M-C31

4. Installation

Attention: During the drive assembly all cabling has to be disconnected from the computer.

1. Take out the PCB.

Technical line drawing of an electronic device housing with internal components and mounting holes (no text or symbols)

1. Combine the circular notch of the round M.2 holder with the semi-circular notch of the M.2 SSD and hold it with one finger (the thinner side upwards). Insert your SSD carefully with the connection side into the M.2 socket at an angle of about 30^ so it fits in smoothly.
2. Then push the SSD card down and fix the M.2 nut with screw as displayed.
3. Place the delivered thermal pad directly to the M.2 NVMe SSD.
4. Put the heat sink on the thermal pad and align the notch to the screw nut.

Manual IB-1825M-C31

1. Install the PCB back into the track inside the housing. Pay attention to the correct alignment!
2. Install the cover and fasten two screws. Please make sure the write protection switch is placed in the square hole when installing the cover.

Technical line drawing of a device housing with multiple circular components and a separate panel (no text or symbols)

Note! Change the write-protect mode before connecting to computer*

5. Usage

- Connect the IB-1825M-C31 via the delivered cable to the corresponding port of your host computer.

Manual IB-1825M-C31

• When the IB-1825M-C31 has been plugged correctly the LED will turn on blue!
• As soon as the write protection has been activated by switch, the status LED continues to light up blue, but no more data can be copied or changed onto the medium*

*Attention! Changing of the write-protect mode will only be activated when the device has been disconnected and then reconnected to the host computer.

6. Application

• The external SSD can be connected or disconnected from the computer without shutting down the computer.
• Please await the end of read/write operations before disconnecting the SSD to avoid data lost.
• A new SSD must first be initialized, partitioned and formatted by the operation system to be displayed by the system.
• If the drive isn't recognized instantly by the operating system please check: if the driver software is installed (USB) if the SSD is initialized, partitioned and formatted.

Hint: Drives must be initialized and have active partitions to be immediately recognized as volumes in the operating system. If this is not the case, initialize the drives in the volume management of your operating system. The full USB 3.1 (Gen2) transfer rate can only be achieved with a compatible USB 3.1 (Gen2) host computer. Furthermore, the USB 3.1 drivers must be installed by the operating system. If this is not the case, install the appropriate drivers for your operating system (Windows ^® , macOS ^® ).

Handbuch IB-1825M-C31

Technical line drawing of an electronic device casing with internal components and mounting holes (no text or symbols)

Technical line drawing of a device housing with multiple circular components and a separate internal component (no text or symbols)

Handbuch IB-1825M-C31

© Copyright 2020 by RaidSonic Technology GmbH. All Rights Reserved

The information contained in this manual is believed to be accurate and reliable. RaidSonic Technology GmbH assumes no responsibility for any errors contained in this manual. RaidSonic Technology GmbH reserves the right to make changes in the specifications and/or design of the above mentioned product without prior notice. The diagrams contained in this manual may also not fully represent the product that you are using and are there for illustration purposes only. RaidSonic Technology GmbH assumes no responsibility for any differences between the product mentioned in this manual and the product you may have. Apple and macOS, MAC, iTunes and Macintosh are registered trademarks of Apple Computer Inc. Microsoft, Windows and the Windows logo are registered trademarks of Microsoft Corporation.